Instructions
Table Of Contents
- Guaranty and Declaration
- Safety Requirement
- MSO5000-E Series Overview
- Document Overview
- Quick Start
- General Inspection
- Appearance and Dimensions
- To Prepare for Use
- Front Panel Overview
- Rear Panel Overview
- Front Panel Function Overview
- User Interface
- Touch Screen Controls
- Parameter Setting Method
- To Use the Kensington Security Lock
- To Use the Built-in Help System
- To View the Option Information and the Option Installation
- To Set the Vertical System
- To Set the Horizontal System
- To Set the Sample System
- To Trigger the Oscilloscope
- Trigger Source
- Trigger LEVEL/Threshold Level
- Trigger Mode
- Trigger Coupling
- Trigger Holdoff
- Noise Rejection
- Trigger Type
- Edge Trigger
- Pulse Trigger
- Slope Trigger
- Video Trigger
- Pattern Trigger
- Duration Trigger
- Timeout Trigger
- Runt Trigger
- Window Trigger
- Delay Trigger
- Setup/Hold Trigger
- Nth Edge Trigger
- RS232 Trigger (Option)
- I2C Trigger (Option)
- SPI Trigger (Option)
- CAN Trigger (Option)
- FlexRay Trigger (Option)
- LIN Trigger (Option)
- I2S Trigger (Option)
- MIL-STD-1553 Trigger (Option)
- Zone Trigger
- Trigger Output Connector
- Operations and Measurements
- Digital Voltmeter (DVM) and Frequency Counter
- Power Analysis (Option)
- Histogram Analysis
- Digital Channel
- Protocol Decoding
- Reference Waveform
- To Enable Ref Function
- To Select the Reference Channel
- To Select the Ref Source
- To Adjust the Ref Waveform Display
- To Save to Internal Memory
- To Clear the Display of the Reference Waveform
- To View Details of the Reference Waveform
- To Reset the Reference Waveform
- Color Setting
- Label Setting
- To Export to Internal or External Memory
- To Import from Internal or External Memory
- Pass/Fail Test
- Waveform Recording & Playing
- Search and Navigation Function
- Display Control
- Function/Arbitrary Waveform Generator (Option)
- Store and Load
- System Utility Function Setting
- Remote Control
- Troubleshooting
- Appendix
- Index
RIGOL Chapter 7 Digital Voltmeter (DVM) and Frequency Counter
7-2 MSO5000-E User Guide
Digital Voltmeter (DVM)
The built-in DVM of this oscilloscope provides 3-digit voltage measurements on any
analog channel. DVM measurements are asynchronous from the oscilloscope’s
acquisition system and are always acquiring.
Press Measure Analyze DVM to open the DVM setting menu, or enable the
touch screen and then tap the function navigation icon at the lower-left corner of
the screen to open the function navigation. Then, tap the "DVM" icon to open the
DVM setting menu. You can also press Measure Add, then in the displayed
measurement category area, rotate the multifunction knob to select "Analyze",
and then select "DVM" to open the DVM setting menu.
To Enable or Disable DVM Measurement
In the "DVM" setting menu, press DVM continuously to enable or disable DVM
measurement. When enabled, the following figure is displayed. The DVM display also
has a scale that is determined by the channel's vertical scale and vertical offset. The
scale range is the range of the screen. The scale's yellow triangle pointer shows the
most recent measurement result. The specific value above the pointer shows the
measurement extrema over the last 3 seconds.
Note: DVM measurement and the oscilloscope share the same probe, so the unit for
the DVM measurement is consistent with that of the channel.
To Select the Measurement Source
Press Source in the "DVM" setting menu, then rotate the multifunction knob to
select the desired source. Press down the knob to select it. You can also press
Source continuously or enable the touch screen to select it. The analog channel
(CH1 or CH2) can be selected to be the measurement source.
Scale Pointer
Source Mode Voltage Value