Instructions

ManualsBrandsRigol ManualsLaboratory EquipmentRigol MSO5152-E Digital 150 MHz 2-channel 4 GS/s 100 KP 8 Bit

Table Of Contents

Guaranty and Declaration
Safety Requirement
- General Safety Summary
- Safety Notices and Symbols
- Measurement Category
- Ventilation Requirement
- Working Environment
- Care and Cleaning
- Environmental Considerations
MSO5000-E Series Overview
Document Overview
Quick Start
- General Inspection
- Appearance and Dimensions
- To Prepare for Use
- Front Panel Overview
- Rear Panel Overview
- Front Panel Function Overview
- User Interface
- Touch Screen Controls
- Parameter Setting Method
- To Use the Kensington Security Lock
- To Use the Built-in Help System
- To View the Option Information and the Option Installation
To Set the Vertical System
- To Enable or Disable the Analog Channel
- To Adjust the Vertical Scale
- Vertical Expansion
- To Adjust the Vertical Offset
- Channel Coupling
- Bandwidth Limit
- Probe Ratio
- Input Impedance
- Waveform Invert
- Amplitude Unit
- Channel Delay
- Offset Cal
- Channel Label
To Set the Horizontal System
- To Adjust the Horizontal Timebase
- To Adjust the Horizontal Position
- Delayed Sweep
To Set the Sample System
- Timebase Mode
- Acquisition Mode
- Sampling Mode
- Sample Rate
- LA Sample Rate
- Memory Depth
- LA Memory Depth
- Anti-Aliasing
- Horizontal Expansion
To Trigger the Oscilloscope
- Trigger Source
- Trigger LEVEL/Threshold Level
- Trigger Mode
- Trigger Coupling
- Trigger Holdoff
- Noise Rejection
- Trigger Type
- Zone Trigger
- Trigger Output Connector
Operations and Measurements
- Math Operation
- Auto Measurement
- Cursor Measurement
Digital Voltmeter (DVM) and Frequency Counter
- Digital Voltmeter (DVM)
- Frequency Counter
Power Analysis (Option)
- Power Quality
- Ripple
Histogram Analysis
- To Enable or Disable the Histogram Function
- To Select the Histogram Type
- To Select the Histogram Source
- To Set the Histogram Height
- To Set the Histogram Range
- To Enable or Disable the Statistical Function
- To Reset
Digital Channel
- To Select the Digital Channel
- To Enable/Disable the Digital Channel
- To Set the Threshold and Calibrate Probe
- Auto Arrangement Setting
- To Set the Waveform Display Size
- To Set the Label
- Group Setting
- Waveform Color of the Digital Channel
Protocol Decoding
- Parallel Decoding
- RS232 Decoding (Option)
- I2C Decoding (Option)
- SPI Decoding (Option)
- LIN Decoding (Option)
- CAN Decoding (Option)
- FlexRay Decoding (Option)
- I2S Decoding (Option)
- 1553B Decoding (Option)
Reference Waveform
- To Enable Ref Function
- To Select the Reference Channel
- To Select the Ref Source
- To Adjust the Ref Waveform Display
- To Save to Internal Memory
- To Clear the Display of the Reference Waveform
- To View Details of the Reference Waveform
- To Reset the Reference Waveform
- Color Setting
- Label Setting
- To Export to Internal or External Memory
- To Import from Internal or External Memory
Pass/Fail Test
- To Enable or Disable the Pass/Fail Test Function
- To Start or Stop the Pass/Fail Test Operation
- To Select the Source
- To Create a Mask
- To Save the Mask
- To Load a Mask
- To Set the Output Form of the Test Results
- To Enable or Disable the Display of the Statistics of the Test Results
- Statistics Reset
Waveform Recording & Playing
- Common Settings
- Record Options
- Play Options
Search and Navigation Function
- Search Function
- Navigation Function
Display Control
- To Select the Display Type
- To Set the Persistence Time
- To Set the Waveform Intensity
- To Set the Screen Grid
- To Set the Grid Brightness
- Scale
- Color Grade
- Waveform Freeze
Function/Arbitrary Waveform Generator (Option)
- To Output Basic Waveforms
- To Output the Arbitrary Waveform
- Modulation
  - AM
  - FM
  - FSK
- Sweep
- Burst
Store and Load
- Storage System
- Storage Type
- Load Type
- Internal Storage and Load
- External Storage and Load
- Disk Management
- Factory Settings
System Utility Function Setting
- Remote Interface Configuration
- System-related
Remote Control
- Remote Control via USB
- Remote Control via LAN
- Remote Control via GPIB
Troubleshooting
Appendix
- Appendix A: Accessories and Options
- Appendix B: Warranty
Index

RIGOL Contents

XVI MSO5000-E User Guide

Abs .............................................................................................. 6-20

Low Pass ...................................................................................... 6-21

High Pass ...................................................................................... 6-22

Band Pass ..................................................................................... 6-23

Band Stop ..................................................................................... 6-24

AX+B ........................................................................................... 6-25

Math Operation Label ..................................................................... 6-26

Auto Measurement ............................................................................... 6-27

Quick Measurement after AUTO ...................................................... 6-27

Measurement Parameter ................................................................ 6-29

Measurement Settings .................................................................... 6-35

Remove the Measurement Result .................................................... 6-38

Statistical Function ......................................................................... 6-38

All Measurement ............................................................................ 6-39

Cursor Measurement ............................................................................ 6-39

Manual Mode ................................................................................ 6-41

Track Mode ................................................................................... 6-45

XY Mode ....................................................................................... 6-47

Measure Mode ............................................................................... 6-49

Chapter 7 Digital Voltmeter (DVM) and Frequency Counter ............. 7-1

Digital Voltmeter (DVM) .......................................................................... 7-2

To Enable or Disable DVM Measurement ............................................ 7-2

To Select the Measurement Source .................................................... 7-2

To Select Measurement Mode ........................................................... 7-3

To Set the Limits ............................................................................. 7-3

Frequency Counter ................................................................................. 7-4

To Enable or Disable the Frequency Counter ....................................... 7-4

To Select the Measurement Source .................................................... 7-4

To Select the Measurement Item ....................................................... 7-4

To Set Resolution ............................................................................. 7-5

To Clear Count ................................................................................ 7-5

To Enable or Disable the Statistical Function ....................................... 7-5

Chapter 8 Power Analysis (Option) .................................................. 8-1

Power Quality ........................................................................................ 8-2

Ripple ................................................................................................... 8-4

Chapter 9 Histogram Analysis .......................................................... 9-1

To Enable or Disable the Histogram Function ............................................ 9-2

To Select the Histogram Type .................................................................. 9-2

To Select the Histogram Source ............................................................... 9-3

To Set the Histogram Height ................................................................... 9-3

To Set the Histogram Range .................................................................... 9-3

To Enable or Disable the Statistical Function ............................................. 9-3

To Reset ................................................................................................ 9-4

Chapter 10 Digital Channel............................................................... 10-1