Instructions
Table Of Contents
- Guaranty and Declaration
- Safety Requirement
- MSO5000-E Series Overview
- Document Overview
- Quick Start
- General Inspection
- Appearance and Dimensions
- To Prepare for Use
- Front Panel Overview
- Rear Panel Overview
- Front Panel Function Overview
- User Interface
- Touch Screen Controls
- Parameter Setting Method
- To Use the Kensington Security Lock
- To Use the Built-in Help System
- To View the Option Information and the Option Installation
- To Set the Vertical System
- To Set the Horizontal System
- To Set the Sample System
- To Trigger the Oscilloscope
- Trigger Source
- Trigger LEVEL/Threshold Level
- Trigger Mode
- Trigger Coupling
- Trigger Holdoff
- Noise Rejection
- Trigger Type
- Edge Trigger
- Pulse Trigger
- Slope Trigger
- Video Trigger
- Pattern Trigger
- Duration Trigger
- Timeout Trigger
- Runt Trigger
- Window Trigger
- Delay Trigger
- Setup/Hold Trigger
- Nth Edge Trigger
- RS232 Trigger (Option)
- I2C Trigger (Option)
- SPI Trigger (Option)
- CAN Trigger (Option)
- FlexRay Trigger (Option)
- LIN Trigger (Option)
- I2S Trigger (Option)
- MIL-STD-1553 Trigger (Option)
- Zone Trigger
- Trigger Output Connector
- Operations and Measurements
- Digital Voltmeter (DVM) and Frequency Counter
- Power Analysis (Option)
- Histogram Analysis
- Digital Channel
- Protocol Decoding
- Reference Waveform
- To Enable Ref Function
- To Select the Reference Channel
- To Select the Ref Source
- To Adjust the Ref Waveform Display
- To Save to Internal Memory
- To Clear the Display of the Reference Waveform
- To View Details of the Reference Waveform
- To Reset the Reference Waveform
- Color Setting
- Label Setting
- To Export to Internal or External Memory
- To Import from Internal or External Memory
- Pass/Fail Test
- Waveform Recording & Playing
- Search and Navigation Function
- Display Control
- Function/Arbitrary Waveform Generator (Option)
- Store and Load
- System Utility Function Setting
- Remote Control
- Troubleshooting
- Appendix
- Index
Chapter 6 Operations and Measurements RIGOL
MSO5000-E User Guide 6-27
Auto Measurement
MSO5000-E series provides auto measurements for 41 waveform parameters, as well
as the statistics and analysis of the measurement results.
Quick Measurement after AUTO
When the oscilloscope is correctly connected and has detected a valid input signal,
press AUTO to enable the waveform auto setting function and open the auto setting
function menu.
: Press this key, and then the complete single period of the signal is
displayed automatically on the screen. Meanwhile, the system will make
measurements for the "frequency" of the currently displayed waveforms in a
complete single period. The measurement results are displayed at the bottom of
the screen.
: Press this key, and then multiple periods of the signal are displayed
automatically on the screen. Meanwhile, the system will make measurements
for the "frequency" of the currently displayed waveforms in a multiple periods.
The measurement results are displayed at the bottom of the screen.
: Press this key, and then one rising edge of the signal is displayed
automatically on the screen. Meanwhile, the system will make measurements
for the "rise time" of the currently displayed rising edge. The measurement
results are displayed at the bottom of the screen. By default, it is intended for
the fast edge signal.
: Press this key, and then one falling edge of the signal is displayed
automatically on the screen. Meanwhile, the system will make measurements
for the "fall time" of the currently displayed falling edge. The measurement
results are displayed at the bottom of the screen. By default, it is intended for
the fast edge signal.
: press this key, and the system returns to the last set menu.
Press Option to enter the auto setting function menu.
Press Lock to lock the AUTO function. To unlock the AUTO function, use the
following two methods:
Method 1: Send the remote command :SYSTem:AUTOscale ON to unlock
the AUTO function.
Method 2: Press Lock again, then a password input dialog box is displayed.
Input the password. By default, there is no password, and pressing OK
directly can unlock the function.