Instructions
Table Of Contents
- Guaranty and Declaration
- Safety Requirement
- MSO5000-E Series Overview
- Document Overview
- Quick Start
- General Inspection
- Appearance and Dimensions
- To Prepare for Use
- Front Panel Overview
- Rear Panel Overview
- Front Panel Function Overview
- User Interface
- Touch Screen Controls
- Parameter Setting Method
- To Use the Kensington Security Lock
- To Use the Built-in Help System
- To View the Option Information and the Option Installation
- To Set the Vertical System
- To Set the Horizontal System
- To Set the Sample System
- To Trigger the Oscilloscope
- Trigger Source
- Trigger LEVEL/Threshold Level
- Trigger Mode
- Trigger Coupling
- Trigger Holdoff
- Noise Rejection
- Trigger Type
- Edge Trigger
- Pulse Trigger
- Slope Trigger
- Video Trigger
- Pattern Trigger
- Duration Trigger
- Timeout Trigger
- Runt Trigger
- Window Trigger
- Delay Trigger
- Setup/Hold Trigger
- Nth Edge Trigger
- RS232 Trigger (Option)
- I2C Trigger (Option)
- SPI Trigger (Option)
- CAN Trigger (Option)
- FlexRay Trigger (Option)
- LIN Trigger (Option)
- I2S Trigger (Option)
- MIL-STD-1553 Trigger (Option)
- Zone Trigger
- Trigger Output Connector
- Operations and Measurements
- Digital Voltmeter (DVM) and Frequency Counter
- Power Analysis (Option)
- Histogram Analysis
- Digital Channel
- Protocol Decoding
- Reference Waveform
- To Enable Ref Function
- To Select the Reference Channel
- To Select the Ref Source
- To Adjust the Ref Waveform Display
- To Save to Internal Memory
- To Clear the Display of the Reference Waveform
- To View Details of the Reference Waveform
- To Reset the Reference Waveform
- Color Setting
- Label Setting
- To Export to Internal or External Memory
- To Import from Internal or External Memory
- Pass/Fail Test
- Waveform Recording & Playing
- Search and Navigation Function
- Display Control
- Function/Arbitrary Waveform Generator (Option)
- Store and Load
- System Utility Function Setting
- Remote Control
- Troubleshooting
- Appendix
- Index
RIGOL Chapter 6 Operations and Measurements
6-2 MSO5000-E User Guide
Math Operation
Press Math in the vertical control area (Vertical) on the front panel to open the math
operation menu. You can also tap the function navigation icon at the lower-left
corner of the screen to open the function navigation. Then tap the "Math" icon to
open the math operation menu. This oscilloscope supports four math operations:
Math1, Math2, Math3, and Math4. The following section takes Math1 as an example
to introduce the math operation in detail.
Press Math Math1 Operator to select the desired math function. Press
Operation continuously to enable or disable the operation. When enabled, the
results of math operation are displayed with purple waveforms on the screen, and
the math operation formula, vertical scale, and other parameters (the displayed data
parameters are different for different math operations) are displayed at the bottom
of the screen. The results of the math operation can be further measured. This
oscilloscope supports enabling the four math operations at the same time, as shown
in the figure below.
MSO5000-E series can realize multiple math operations between waveforms of
different channels, including
arithmetic operations (A+B, A-B, A×B, and A/B)
FFT operation
logic operation: A&&B, A||B, A^B, and !A
function operation: Intg, Diff, Sqrt, Lg, Ln, Exp, Abs, and AX+B (linear function)
math filter: low-pass filter, high-pass filter, band-pass filter, and band-stop filter
Note: When you select the source, only the enabled channel is available.
Addition
Adds the waveform voltage values of signal source A and B point by point and
displays the results.
Press MATH Math1 Operator to select "A+B":
Press Operation continuously to enable or disable the addition operation
function.
Press SourceA and SourceB respectively, and rotate the multifunction knob
to select the channel for Source A and Source B. Then press down the knob