User Manual

ManualsBrandsRIGOL ManualsLaboratory Test EquipmentDigital 100 MHz 18-channel 1 null 7 null 8 Bit Digital storage (DSO), Mixed signal (MSO), Logic analyz

326

327

328

329

330

331

332

333

334

335

Table Of Contents

Guaranty and Declaration
Safety Requirement
- General Safety Summary
- Safety Terms and Symbols
- Allgemeine Sicherheits Informationen
- Sicherheits Begriffe und Symbole
- Measurement Category
- Ventilation Requirement
- Working Environment
- General Care and Cleaning
- Environmental Considerations
MSO2000A/DS2000A Series Overview
Document Overview
Chapter 1 Quick Start
- General Inspection
- Appearance and Dimensions
- To Prepare the Oscilloscope for Use
- Front Panel Overview
- Rear Panel Overview
- Front Panel Function Overview
- User Interface
- To Use the Security Lock
- To Use the Built-in Help System
Chapter 2 To Set the Vertical System
- To Enable the Analog Channel
- Channel Coupling
- Bandwidth Limit
- Probe Ratio
- Input Impedance
- Waveform Invert
- Vertical Scale
- Vertical Expansion
- Amplitude Unit
- Channel Label
- Delay Calibration of the Analog Channel
Chapter 3 To Set the Horizontal System
- Delayed Sweep
- Time Base Mode
- Horizontal Scale
- Horizontal Reference
Chapter 4 To Set the Sample System
- Acquisition Mode
- Sample Mode
- Sample Rate
- LA Sample Rate
- Memory Depth
- LA Memory Depth
- Anti-Aliasing
Chapter 5 To Trigger the Oscilloscope
- Trigger Source
- Trigger Mode
- Trigger Coupling
- Trigger Holdoff
- Noise Rejection
- Trigger Type
- Trigger Output Connector
Chapter 6 MATH and Measurements
- Math Operation
- Auto Measurement
- Cursor Measurement
Chapter 7 Digital Channel
- To Select the Digital Channel
- To Move the Digital Channel
- To Turn on/off the Digital Channel
- Group Set
- To Set the Waveform Display Size
- Reorder Setting
- To Set the Threshold
- To Use the Digital Bus
- To Set the Label
- Digital Channel Delay Calibration
Chapter 8 Protocol Decoding
- Parallel Decoding
- RS232 Decoding (Option)
- I2C Decoding (Option)
- SPI Decoding (Option)
- CAN Decoding (Option)
Chapter 9 Reference Waveform
- To Enable REF Function
- To Set the Color
- To Select REF Source
- To Save REF Waveform
- To Adjust REF Waveform Display
- To Export to Internal or External Memory
- To Import from Internal or External Memory
Chapter 10 Pass/Fail Test
- To Enable Pass/Fail Test
- To Select Source
- Mask Range
- To Set Test Results Output Type
- To Save the Test Mask
- To Load the Test Mask
Chapter 11 Waveform Record
- Waveform Record
- Record Constant On
- Waveform Playback
- Waveform Analysis
  - Analysis Based on Trace
  - Analysis Based on Pass/Fail Mask
Chapter 12 Display Control
- To Select the Display Type
- To Set the Persistence Time
- To Set the Waveform Intensity
- To Set the Screen Grid
- To Set the Grid Brightness
- To Set the Menu Display
Chapter 13 Signal Source
- Parameter Setting Method
- To Output Basic Waveform
- To Output Built-in Waveform
- To Output Arbitrary Waveform
- Modulation
  - AM
  - FM
Chapter 14 Store and Recall
- Storage System
- Storage Type
- Internal Storage and Recall
- External Storage and Recall
- Disk Management
- Factory
Chapter 15 System Function Setting
- Remote Interface Configuration
- System-related
Chapter 16 Remote Control
- Remote Control via USB
- Remote Control via LAN
- Remote Control via GPIB
Chapter 17 Troubleshooting
Chapter 18 Specifications
Chapter 19 Appendix
- Appendix A: Accessories and Options
- Appendix B: Warranty
Index

RIGOL Index

MSO2000A/DS2000A User’s Guide

Noise rejection ........................... 5-7

Normal ...................................... 4-2

NOT ........................................ 6-10

Nth Edge Trigger ...................... 5-19

Operator .................................. 6-14

Option Management ................ 15-17

OR .......................................... 6-10

Overshoot ................................ 6-22

Parallel Decoding ........................ 8-2

Pass/Fail Test ........................... 10-1

Pattern Setting ................. 5-27, 5-34

Pattern Trigger ......................... 5-27

Peak Detect ............................... 4-4

Period ..................................... 6-18

Period Area .............................. 6-22

Persistence Time ...................... 12-2

Phase ...................................... 6-19

Picture ..................................... 14-3

Preshoot .................................. 6-22

Pulse ....................................... 13-6

Pulse Condition ........................ 5-11

Pulse Polarity ........................... 5-14

Pulse Trigger ............................ 5-11

Pulse Width Setting................... 5-12

Qualifier .................................. 5-15

Ramp ...................................... 13-5

Record Constant On .................. 11-4

Rectangle .................................. 6-6

Reference Waveform ................... 9-1

Rise Time ................................ 6-18

Roll ........................................... 3-7

RS232 Decoding ......................... 8-5

RS232 Trigger .......................... 5-38

Runt Trigger ............................. 5-14

Sample Rate .............................. 4-6

Setup/Hold Trigger ................... 5-36

Setups ..................................... 14-3

Signal Source ............................ 13-1

Sine ......................................... 13-3

Slope Condition ......................... 5-21

Slope Trigger ............................ 5-21

SPI Decoding ............................ 8-14

SPI Trigger ............................... 5-44

Square ..................................... 13-4

Static IP ................................... 15-3

Subnet Mask ............................. 15-4

Symmetry................................. 13-5

Sync

........................................ 5-24

Threshold ........................ 6-18, 6-25

Time Setting ............................. 5-22

TimeOut Trigger ........................ 5-32

Traces ...................................... 14-3

Track Mode ............................... 6-35

Trigger Coupling .......................... 5-5

Trigger Holdoff ............................ 5-6

Trigger Level ............................. 5-10

Trigger Mode .............................. 5-3

Trigger Position ......................... 5-17

Trigger Source ............................ 5-2

USB ......................................... 15-7

USB Trigger .............................. 5-47

Vamp ....................................... 6-21

Variable .................................... 6-13

Vavg ........................................ 6-21

Vbase ...................................... 6-21

Vectors .................................... 12-2

Vertical Expansion ....................... 2-7

Vertical Scale .............................. 2-6

Vertical Window ............... 5-15, 5-22

Video Polarity ........................... 5-24

Video Standard ......................... 5-25

Video Trigger ............................ 5-24

VISA ........................................ 15-6

Vmax ....................................... 6-21