User Manual

ManualsBrandsRIGOL ManualsLaboratory Test EquipmentDigital 100 MHz 18-channel 1 null 7 null 8 Bit Digital storage (DSO), Mixed signal (MSO), Logic analyz

Table Of Contents

Guaranty and Declaration
Safety Requirement
- General Safety Summary
- Safety Terms and Symbols
- Allgemeine Sicherheits Informationen
- Sicherheits Begriffe und Symbole
- Measurement Category
- Ventilation Requirement
- Working Environment
- General Care and Cleaning
- Environmental Considerations
MSO2000A/DS2000A Series Overview
Document Overview
Chapter 1 Quick Start
- General Inspection
- Appearance and Dimensions
- To Prepare the Oscilloscope for Use
- Front Panel Overview
- Rear Panel Overview
- Front Panel Function Overview
- User Interface
- To Use the Security Lock
- To Use the Built-in Help System
Chapter 2 To Set the Vertical System
- To Enable the Analog Channel
- Channel Coupling
- Bandwidth Limit
- Probe Ratio
- Input Impedance
- Waveform Invert
- Vertical Scale
- Vertical Expansion
- Amplitude Unit
- Channel Label
- Delay Calibration of the Analog Channel
Chapter 3 To Set the Horizontal System
- Delayed Sweep
- Time Base Mode
- Horizontal Scale
- Horizontal Reference
Chapter 4 To Set the Sample System
- Acquisition Mode
- Sample Mode
- Sample Rate
- LA Sample Rate
- Memory Depth
- LA Memory Depth
- Anti-Aliasing
Chapter 5 To Trigger the Oscilloscope
- Trigger Source
- Trigger Mode
- Trigger Coupling
- Trigger Holdoff
- Noise Rejection
- Trigger Type
- Trigger Output Connector
Chapter 6 MATH and Measurements
- Math Operation
- Auto Measurement
- Cursor Measurement
Chapter 7 Digital Channel
- To Select the Digital Channel
- To Move the Digital Channel
- To Turn on/off the Digital Channel
- Group Set
- To Set the Waveform Display Size
- Reorder Setting
- To Set the Threshold
- To Use the Digital Bus
- To Set the Label
- Digital Channel Delay Calibration
Chapter 8 Protocol Decoding
- Parallel Decoding
- RS232 Decoding (Option)
- I2C Decoding (Option)
- SPI Decoding (Option)
- CAN Decoding (Option)
Chapter 9 Reference Waveform
- To Enable REF Function
- To Set the Color
- To Select REF Source
- To Save REF Waveform
- To Adjust REF Waveform Display
- To Export to Internal or External Memory
- To Import from Internal or External Memory
Chapter 10 Pass/Fail Test
- To Enable Pass/Fail Test
- To Select Source
- Mask Range
- To Set Test Results Output Type
- To Save the Test Mask
- To Load the Test Mask
Chapter 11 Waveform Record
- Waveform Record
- Record Constant On
- Waveform Playback
- Waveform Analysis
  - Analysis Based on Trace
  - Analysis Based on Pass/Fail Mask
Chapter 12 Display Control
- To Select the Display Type
- To Set the Persistence Time
- To Set the Waveform Intensity
- To Set the Screen Grid
- To Set the Grid Brightness
- To Set the Menu Display
Chapter 13 Signal Source
- Parameter Setting Method
- To Output Basic Waveform
- To Output Built-in Waveform
- To Output Arbitrary Waveform
- Modulation
  - AM
  - FM
Chapter 14 Store and Recall
- Storage System
- Storage Type
- Internal Storage and Recall
- External Storage and Recall
- Disk Management
- Factory
Chapter 15 System Function Setting
- Remote Interface Configuration
- System-related
Chapter 16 Remote Control
- Remote Control via USB
- Remote Control via LAN
- Remote Control via GPIB
Chapter 17 Troubleshooting
Chapter 18 Specifications
Chapter 19 Appendix
- Appendix A: Accessories and Options
- Appendix B: Warranty
Index

RIGOL Contents

XXIV MSO2000A/DS2000A User’s Guide

Multiplication ................................................................................... 6-3

Division .......................................................................................... 6-3

FFT ................................................................................................ 6-5

Digital Filter .................................................................................... 6-8

Logic Operation ............................................................................. 6-10

Advanced Operation ....................................................................... 6-12

MATH Label................................................................................... 6-14

Auto Measurement ............................................................................... 6-15

Quick Measurement after AUTO ...................................................... 6-15

One-key Measurement of 29 Parameters .......................................... 6-17

Frequency Counter Measurement .................................................... 6-23

Measurement Setting ..................................................................... 6-24

To Clear the Measurement .............................................................. 6-26

All Measurement ............................................................................ 6-27

Statistic Function ........................................................................... 6-28

Measurement History ..................................................................... 6-28

Cursor Measurement ............................................................................ 6-29

Manual Mode ................................................................................ 6-30

Track Mode ................................................................................... 6-35

Auto Mode .................................................................................... 6-38

X-Y Mode ...................................................................................... 6-39

Chapter 7 Digital Channel ..................................................................... 7-1

To Select the Digital Channel ................................................................... 7-2

To Move the Digital Channel .................................................................... 7-2

To Turn on/off the Digital Channel ........................................................... 7-3

Group Set .............................................................................................. 7-4

To Set the Waveform Display Size ............................................................ 7-5

Reorder Setting ...................................................................................... 7-5

To Set the Threshold .............................................................................. 7-5

To Use the Digital Bus ............................................................................ 7-6

To Set the Label ..................................................................................... 7-7

Digital Channel Delay Calibration ............................................................. 7-8

Chapter 8 Protocol Decoding ................................................................ 8-1

Parallel Decoding ................................................................................... 8-2

RS232 Decoding (Option) ....................................................................... 8-5

I2C Decoding (Option) .......................................................................... 8-10