User Manual

ManualsBrandsRIGOL ManualsLaboratory Test EquipmentDigital 100 MHz 18-channel 1 null 7 null 8 Bit Digital storage (DSO), Mixed signal (MSO), Logic analyz

Table Of Contents

Guaranty and Declaration
Safety Requirement
- General Safety Summary
- Safety Terms and Symbols
- Allgemeine Sicherheits Informationen
- Sicherheits Begriffe und Symbole
- Measurement Category
- Ventilation Requirement
- Working Environment
- General Care and Cleaning
- Environmental Considerations
MSO2000A/DS2000A Series Overview
Document Overview
Chapter 1 Quick Start
- General Inspection
- Appearance and Dimensions
- To Prepare the Oscilloscope for Use
- Front Panel Overview
- Rear Panel Overview
- Front Panel Function Overview
- User Interface
- To Use the Security Lock
- To Use the Built-in Help System
Chapter 2 To Set the Vertical System
- To Enable the Analog Channel
- Channel Coupling
- Bandwidth Limit
- Probe Ratio
- Input Impedance
- Waveform Invert
- Vertical Scale
- Vertical Expansion
- Amplitude Unit
- Channel Label
- Delay Calibration of the Analog Channel
Chapter 3 To Set the Horizontal System
- Delayed Sweep
- Time Base Mode
- Horizontal Scale
- Horizontal Reference
Chapter 4 To Set the Sample System
- Acquisition Mode
- Sample Mode
- Sample Rate
- LA Sample Rate
- Memory Depth
- LA Memory Depth
- Anti-Aliasing
Chapter 5 To Trigger the Oscilloscope
- Trigger Source
- Trigger Mode
- Trigger Coupling
- Trigger Holdoff
- Noise Rejection
- Trigger Type
- Trigger Output Connector
Chapter 6 MATH and Measurements
- Math Operation
- Auto Measurement
- Cursor Measurement
Chapter 7 Digital Channel
- To Select the Digital Channel
- To Move the Digital Channel
- To Turn on/off the Digital Channel
- Group Set
- To Set the Waveform Display Size
- Reorder Setting
- To Set the Threshold
- To Use the Digital Bus
- To Set the Label
- Digital Channel Delay Calibration
Chapter 8 Protocol Decoding
- Parallel Decoding
- RS232 Decoding (Option)
- I2C Decoding (Option)
- SPI Decoding (Option)
- CAN Decoding (Option)
Chapter 9 Reference Waveform
- To Enable REF Function
- To Set the Color
- To Select REF Source
- To Save REF Waveform
- To Adjust REF Waveform Display
- To Export to Internal or External Memory
- To Import from Internal or External Memory
Chapter 10 Pass/Fail Test
- To Enable Pass/Fail Test
- To Select Source
- Mask Range
- To Set Test Results Output Type
- To Save the Test Mask
- To Load the Test Mask
Chapter 11 Waveform Record
- Waveform Record
- Record Constant On
- Waveform Playback
- Waveform Analysis
  - Analysis Based on Trace
  - Analysis Based on Pass/Fail Mask
Chapter 12 Display Control
- To Select the Display Type
- To Set the Persistence Time
- To Set the Waveform Intensity
- To Set the Screen Grid
- To Set the Grid Brightness
- To Set the Menu Display
Chapter 13 Signal Source
- Parameter Setting Method
- To Output Basic Waveform
- To Output Built-in Waveform
- To Output Arbitrary Waveform
- Modulation
  - AM
  - FM
Chapter 14 Store and Recall
- Storage System
- Storage Type
- Internal Storage and Recall
- External Storage and Recall
- Disk Management
- Factory
Chapter 15 System Function Setting
- Remote Interface Configuration
- System-related
Chapter 16 Remote Control
- Remote Control via USB
- Remote Control via LAN
- Remote Control via GPIB
Chapter 17 Troubleshooting
Chapter 18 Specifications
Chapter 19 Appendix
- Appendix A: Accessories and Options
- Appendix B: Warranty
Index

RIGOL

X MSO2000A/DS2000A User’s Guide

Measurement Category

MSO2000A/DS2000A series digital oscilloscopes can make measurements in

Measurement Category I.

WARNING

This oscilloscope can only be used for measurements within its specified

measurement categories.

Measurement Category Definitions

Measurement category I is for measurements performed on circuits not directly

connected to MAINS. Examples are measurements on circuits not derived from

MAINS, and specially protected (internal) MAINS derived circuits. In the latter case,

transient stresses are variable; for that reason, the transient withstand capability of

the equipment is made known to the user.

Measurement category II is for measurements performed on circuits directly

connected to the low voltage installation. Examples are measurements on household

appliances, portable tools and similar equipment.

Measurement category III is for measurements performed in the building installation.

Examples are measurements on distribution boards, circuit-breakers, wiring,

including cables, bus-bars, junction boxes, switches, socket-outlets in the fixed

installation, and equipment for industrial use and some other equipment, for

example. Stationary motors with permanent connection to the fixed installation.

Measurement category IV is for measurements performed at the source of the

low-voltage installation. Examples are electricity meters and measurements on

primary overcurrent protection devices and ripple control units.