Data Sheet

Display
Display Type
Display Resolution
Display Color
Persistence Time
Display Type
Real-time Clock
I/O
Standard Ports
Printer Compatibility
10.1 inches (257 mm) TFT LCD display
800 Horizontal ×RGB×480 Vertical Pixel
160,000 Color
Minimum, 1 s, 2 s, 5 s, 10 s, 20 s, Innite
Dots, Vectors
Time and Date (user adjustable)
USB device, two USB host ports, LAN, VGA
Output, 10 MHz Input/Output, Aux output
(TrigOut, Quick Edge, PassFail, Calibration, GND)
PictBridge
Video Trigger
Signal Standard
Line Frequency
Range
Pattern Trigger
Pattern Setting
RS232/UART Trigger
Trigger Condition
Baud Rate
Data Bits
I2C Trigger
Trigger Condition
Address Bits
Address Range
Data Range
Data Qualier
SPI Trigger
Trigger Condition
Timeout Value
Data Bits
Data Line Setting
Clock Edge
Signal Type
CAN Trigger
Trigger Condition
Baud Rate
Sample Point
Frame Type
USB Trigger
Signal Speed
Trigger condition
Measure
Cursor
Auto Measurement
Number of
Measurements
Measurement Range
Measurement
Statistic
Frequency Counter
Support standard NTSC, PAL and SECAM
broadcasting standards, the range of the
number of lines is from 1 to 525 (NTSC)
and 1 to 625 (PAL/SECAM)
H, L, X, Rising Edge, Falling Edge
Start, Error, Check Error, Data
2400bps, 4800bps, 9600bps, 19200bps,
38400bps, 57600bps, 115200bps, User
5 bit, 6 bit, 7 bit, 8 bit
Start, Restart, Stop, Missing ACK, Address,
Data, A&D
7 bit, 10 bit
1 to 127
0 to 255
Equal to, Greater than, Less than
CS, Timeout
100 ns to 999 ns
4 bit to 32 bit
H, L, X
Rising Edge, Falling Edge
Rx, Tx, CAN_H, CAN_L, Differential
SOF, EOF, Frame Type
10kbps, 20kbps, 33.3kbps, 50kbps,
62.5kbps, 83.3kbps, 100kbps, 125kbps,
250kbps, 500kbps, 800kbps, 1Mbps, User
5% to 95%
Data, Remote, Error, OverLoad
Low Speed, Full Speed
SOP, EOP, RC, Suspended, Exit Suspended
Manual Mode
Track Mode
Auto Mode
Measurements of Maximum, Minimum,
Peak-Peak Value, Top Value, Bottom Value,
Amplitude, Average, Mean Square Root,
Overshoot, Pre-shoot, Frequency, Period,
Rise Time, Fall Time, Positive Pulse Width,
Negative Pulse Width, Positive Duty Cycle,
Negative Duty Cycle, Delay A~B
, Delay
A~B
, Phase A~B , Phase A~B
Display 5 measurements at the same time.
Screen or cursor.
Average, Max, Min, Standard Deviation,
Number of Measurements
Hardware 6 bits frequency counter
(channels available: DS606x, CH1/CH2;
DS610x, CH1/CH2/CH3/CH4)
Voltage Deviation between
Cursors (
△
V)
Time Deviation between
Cursors (
△
T)
Reciprocal of
△
T (Hz) (1/
△
T)
Voltage and Time Values of
the Waveform Point
Allow to display cursors
during auto measurement
General Specications
Probe Compensation Output
Output Voltage
2
Frequency
2
Power
Power Voltage
Power
Fuse
Environment
Temperature Range
Cooling Method
Humidity Range
Altitude
Size
3
Weight
4
1. Maximum value. In single-channel mode, sine signal with 10 ns horizontal scale,
4 div input amplitude and 10 MHz frequency, edge trigger.
2. Typical.
3. Tilt tabs and handle folded, knob height included, front panel cover excluded.
4. DS1064 model, standard conguration.
About 3 V, peak-peak
1 kHz
100-120 V/45-440 Hz
100-240 V/45-65 Hz
Maximum 150W
3 A, T Degree, 250 V
Operation: 0
℃
to +50
℃
Non-Operation: -20
℃
to +70
℃
fan cooling
Under +35
℃
: ≤90% Relative Humidity
+35
℃
to +50
℃
: ≤60% Relative Humidity
Operation: under 3,000 meters
Non-Operation: under 15,000 meters
Width×Height×Depth =
399.0 mm×255.3 mm×123.8 mm
Package Excluded
Package Included
5.345 ± 0.2 kg
10.8 ± 1 kg
Math Operation
Waveform Operation
FFT Window Function
FFT Display
FFT Vertical Scale
Logic Operation
Math Function
Number of Buses for
Decoding
Decoding Type
A+B, A-B, A×B, A/B, FFT, Editable Advanced
Operation, Logic Operation
Rectangle, Hanning, Blackman, Hamming
Split, Full Screen
Linear RMS, dBV RMS
AND, OR, NOT, XOR
Intg, Diff, Log, Exp, Sqrt, Sine, Cosine, Tangent
2
Parallel(standard),RS232/UART(option),
I2C/SPI(option)
Physical Characteristics
Calibration Interval
The recommended calibration interval period is one year.
Regulatory Information
Electromagnetic
Compatibility
Safety
2004/108/EC
Execution standard EN 61326-1:2006 EN
61326-2-1:2006
UL 61010-1:2004 ; CAN/CSA-C22.2 NO.
61010-1-2004 ;
EN 61010-1:2001 ; IEC 61010-1:2001