Information

ManualsBrandsRIGOL ManualsLaboratory & Bench PSUsBench PSU (adjustable voltage) 0.01 - 30 V 0.01 - 5 A

Chapter 5 Specifications RIGOL

DP700 User’s Guide 5-1

Chapter 5 Specifications

All the technical specifications are guaranteed when the instrument has been

working for more than 30 minutes under the specified operating temperature.

DC Output (0°C to 40°C)

Model Voltage/Current Rating OVP/OCP

DP711 0 V to 30 V/0 A to 5 A 0.01 V to 33 V/0.01 A to 5.5 A

DP712 0 V to 50 V/0 A to 3 A 0.01 V to 55 V/0.01 A to 3.3 A

Load Regulation, ±(% of Output + Offset)

Voltage <0.01% + 2 mV

Current <0.01% + 2 mA

Line Regulation, ±(% of Output + Offset)

Voltage <0.01% + 2 mV

Current <0.01% + 2 mA

Ripple and Noise (20 Hz to 20 MHz)

Model Normal Mode Voltage Normal Mode Current

DP711 <500 μVrms/3 mVpp

<2 mArms

DP712 <500 μVrms/4 mVpp

Annual Accuracy

[1]

(25°C ± 5°C), ±(% of Output + Offset)

Programming

Voltage 0.05% + 20 mV

Current 0.2% + 10 mA

Readback

Voltage 0.05% + 20 mV

Current 0.2% + 20 mA

Resolution

Programming

Voltage

Standard: 10 mV

High resolution option installed: 1 mV

Current

Standard: 10 mA

High resolution option installed: 1 mA

Readback

Voltage

Standard: 10 mV

High resolution option installed: 1 mV

Current

Standard: 10 mA

High resolution option installed: 1 mA

Display

Voltage

Standard: 10 mV

High resolution option installed: 1 mV

Current

Standard: 10 mA

High resolution option installed: 1 mA

Summary of content (3 pages)

PAGE 1
RIGOL Chapter 5 Specifications Chapter 5 Specifications All the technical specifications are guaranteed when the instrument has been working for more than 30 minutes under the specified operating temperature. DC Output (0°C to 40°C) Model Voltage/Current Rating DP711 0 V to 30 V/0 A to 5 A DP712 0 V to 50 V/0 A to 3 A OVP/OCP 0.01 V to 33 V/0.01 A to 5.5 A 0.01 V to 55 V/0.01 A to 3.3 A Load Regulation, ±(% of Output + Offset) Voltage <0.01% + 2 mV Current <0.
PAGE 2
RIGOL Chapter 5 Specifications Transient Response Time Less than 50 μs for output voltage to recover to within 15 mV following a change in output current from full load to half load or from half load to full load. Command Processing Time[2] <100 ms OVP/OCP Accuracy, ±(% of Output + Offset) OVP Activation Time 0.5% + 0.5 V/0.5% + 0.
PAGE 3
RIGOL Chapter 5 Specifications Maximum Output Floating Voltage to Ground Storage Temperature Humidity ±240 Vdc -40°C to 70°C 5% to 80% RH Altitude Below 2,000 m Note[1]: The accuracy parameters are acquired through calibration under 25°C after 1-hour warm-up. Note[2]: The maximum time required for the output to begin to change after receiving the APPLy and SOURce commands. Note[3]: Exclude the command processing time. Note[4]: Maximum change in output/readback per °C after a 30-minute warm-up.