User manual
270416 9
SAFE 2
NOT-
STOP
AUS/
E-
S
ext.
ext.
U
24V AC/DC
START
K1 ext.
K2 ext.
S33 S34
A1(+)
S11
A2(-)
S21 S22
23
ext.
K2
24
K1
ext.
S12
13
1414
33 41
bis Kategorie 4; SIL3; PLe erreichbar
up to category 4; SIL3; PLe reachable
bis Kategorie 4; SIL3; PLe erreichbar
up to category 4; SIL3; PLe reachable
bis Kategorie 4; SIL3; PLe erreichbar
up to category 4; SIL3; PLe reachable
Beispiel 4: Zweikanalige Not-Halt-
Schaltung mit externer Kontak-
terweiterung (2Schütze), Kontakt-
überwachung und Querschlußsi-
cherheit. Safe 2/2.1
In diesem Beispiel werden zwei
externe Schütze mit Kon-
taktzwangsführung verwendet. Je
ein Öffnerkontakt dieser beiden
Schütze muß in Reihe zum START-
Taster an die Klemmen S33 und
S34 angeschlossen werden. Über
einen Schalter S ext. können die
externen Schütze zu einem beliebi-
gen Zeitpunkt dazugeschalten bzw.
abgeschalten werden, wenn das
SAFE 2... aktiviert ist. Die Anschluß-
leitungen für die Schütze sollten zur
Vermeidung von Querschlüssen
getrennt verdrahtet werden.
Beispiel 5: Zweikanalige Schutz-
türüberwachung (mit Querschluß-
sicherheit). Safe 2/2.1
Werden die Schutztürschalter S1
und S2 geschlossen, bleiben die
Ausgangskontakte unverändert. Erst
mit Freigabe wird das Gerät akti-
viert. Die Kontakte13-14,23-24
schließen. Beim Öffnen des Schutz-
türtasters fallen die Kontakte unver-
zögert in ihre Grundstellung zurück.
Beispiel 6: Zweikanalige Schutz-
türüberwachung mit automati-
scher Aktivierung und Quer-
schlußsicherheit. Safe 2.1
In diesem Beispiel erfolgt die Akti-
vierung des Gerätes automatisch,
da S33 und S34 überbrückt sind.
Wird der Schutztürtaster geschlos-
sen, schließen die Kontakte 13-14
und 23-24. Beim Öffnen des Schutz-
türtasters fallen die Kontakte unver-
zögert in ihre Grundstellung zurück.
Dieses Anwendungsbeispiel ist nur
mit der Gerätevariante SAFE 2.1
ohne Überwachung der START-
Taste möglich.
Example 4: Dual-channel emer-
gency stop with external contact
extension (2 contactors), contact
monitoring and opposite polarity
between channels. Safe 2/2.1
This application uses two external
contactors with positive guidance.
One normally closed contact of each
external contactors must be con-
nected in series to the START-
button to the terminals S33 and
S34. Through the switch S ext. the
external contactors can be operated
or turned off at any time if the SAFE
2... is activated.
Example 5: Dual-channel protec-
tion door monitoring with oppo-
site polarity between channels.
Safe 2/2.1
If the safety gate switches are
closed, the output contacts remain
unchanged. After the release of the
unit, the contacts 13-14 and 23-24
close. After opening the protection
door switches the contacts return to
their normal position without delay.
Example 6: Dual-channel protec-
tion door monitoring with auto-
matic activation and with oppo-
site polarity between channels.
Safe 2.1
For this application the unit SAFE
2.1 has to be used. The activation
works automatically, since the ter-
minals S33/S34 are bridged. If the
protection door switches close, the
contacts 13-14, 23-24 close. After
the opening of the protection door
switches the contacts return to their
normal position without delay.
24V AC/DC
A2(-)
S34 S33
A1(+)
Freigabe/
release
S22 S21S12 S11
23
13
S2S1
24V AC/DC
A2(-)
S34 S33
A1(+)
S22 S21S12 S11
23
13
S2S1