76 2:1(5·6 0$18$/ ,1&+ &2175$&725 6(5,(6 %(/7 '5,9( 6$: $VVHPEO\ 2SHUDWLRQ 5HSDLU 3DUWV )RU
Table of Contents Section Page Safety Instructions For Table Saw ................................. 3 Safety Signal Words ................................................... 3 Before Using The Saw ................................................ 3 When Installing Or Moving The Saw ........................... 3 Before Each Use ......................................................... 4 To Reduce the Risk of Injury From Jams, Slips Or Thrown Pieces (Kickbacks Or Throwbacks) ..............
Safety Instructions For Table Saw Safety is a combination of common sense, staying alert and knowing how your table saw works. Read this manual to understand this table saw. Safety Signal Words WARNING: means if the safety information is not followed someone could be seriously injured or killed. CAUTION: means if the safety information is not followed someone may be injured. DANGER: means if the safety information is not followed someone will be seriously injured or killed.
Safety Instructions For Table Saw (continued) Before Each Use Inspect your saw. • To reduce the risk of injury from accidental starting, turn the switch off, unplug the saw, and remove the switch key before raising or removing the guard, changing the cutting tool, changing the setup, or adjusting anything. Make sure switch is in OFF position before plugging in.
Plan Ahead To Protect Your Eyes, Hands, Face and Ears Dress for safety • Do not wear loose clothing, gloves, neckties or jewelry (rings, wrist watches). They can get caught and draw you into moving parts. • Wear nonslip footwear. • Tie back long hair. • Roll long sleeves above the elbow. • Noise levels vary widely. To reduce the risk of possible hearing damage, wear ear plugs or muffs when using table saw for hours at a time. • Any power saw can throw foreign objects into the eyes.
Safety Instructions For Table Saws (continued) Additional Safety Instructions For: Rip Type Cuts. • Never use the miter gauge when ripping. • Use a push stick whenever the fence is 2 or more inches from the blade. • When thru-sawing, use an auxiliary fence and push block whenever the fence must be between 1/2 and 2 inches of the blade. • Never thru-saw rip cuts narrower than 1/2 inch. (See “Basic Saw Operations-Ripping and Bevel Ripping” sections.) • Never rip anything shorter than 10” long.
Glossary of Terms for Woodworking Anti-Kickback Pawls Device which, when properly maintained, is designed to stop the workpiece from being thrown towards the front of the saw at the operator during ripping operation. Arbor The shaft on which a cutting tool is mounted. Bevel Cut An angle cutting operation made through the face of the workpiece. Compound Cut A simultaneous bevel and miter crosscutting operation. Crosscut A cutting operation made across the width of the workpiece.
Motor Specifications and Electrical Requirements Power Supply and Motor Specifications 60 Hz. service. Wired for 120V WARNING: To reduce the risk of electrical hazards, fire hazards or damage to the tool, use proper circuit protection. Your tool is wired at the factory for operation using the voltage shown. Connect tool to a power line with the appropriate voltage and a 15-amp branch circuit. Use a 15-amp time delay type fuse or circuit breaker.
Changing Motor Voltage WARNING: Electric shock can kill. To reduce the risk of shock, never connect plug to power source outlet until all assembly steps are completed. Unplug saw before making or changing any connections. Power Cord NOTE: Power cord lead connections for 110/120 volt and 220/240 volt applications are the same. This will show how to change the internal motor wiring to convert saw from a 120V to a 240V application. 1.
Motor Specifications and Electrical Requirements (continued) Motor Thermal Overload Protector CAUTION: To reduce the risk of motor damage, this motor should be blown out or vacuumed frequently to prevent sawdust buildup which will interfere with normal motor ventilation.
Unpacking and Checking Contents Tools Needed Hex “L” Wrenches 3/32 In., 2.5mm, 1/8 In., 5/32 In., 3/16 In. Combination Square must be true. Check it’s accuracy as shown below. Hammer Draw light line on board along edge Select the straight edge of 3/4” thick board. This edge must be perfectly straight. Utility Knife Pliers NOTE: The square and straight edge are used to align the saw. They must be accurate if the saw is to be aligned properly.
Unpacking and Checking Contents (continued) List of Loose Parts Item Part Name Qty. Fence Guide Bar Carton Containing: R Front Fence Guide Bar ......................................... 1 S Rear Fence Guide Bar ......................................... 1 T Guide Bar Parts Bag ............................................ 1 Rip Fence Carton Containing: U Rip Fence ............................................................. 1 Motor Carton Containing: V Motor/Switch Assembly ...................................
List of Loose Parts (Caster) Item A B C D Description Qty. Center Frame ...................................................... 1 Center Frame w/Actuator ..................................... 1 End Frame without Wheel.................................... 2 End Frame with Fixed Wheel ............................... 2 Item E F G H Description Qty. Handle ..................................................................1 Hinge Plate ...........................................................1 Swivel Caster .
Assembly (continued) Assembling Leg Stand 1. Locate the carton containing the leg stand. Remove all parts from packing material. 2. From the bag labeled “Legs” remove the following hardware: 20 Truss Head Screws, 1/4-20 x 1/2” long 20 Lockwashers, 1/4” External Type 20 Hex Nuts, 1/4-20 From leg stand carton find the following: 4 Legs 2 End Stringers 2 Side Stringers 2 Leg Braces 3. From among the loose parts find the following: 2 Miter Gauge Storage Hooks 2 Rip Fence Storage Hooks 1/4 In.
Assembling Universal Caster System Frame Assembly Locating Parts 1. From the bag labeled "Caster" remove only the following hardware: 24 Truss Head Screws, 1/4-20 x 1/2" Long 24 Lockwashers, 1/4" External Type 24 Hex Nuts, 1/4-20 2. From the caster carton find the following: 2 End Frames Without Wheel 2 End Frames With Wheel 1 Center Frame with Actuator 1 Center Frame Truss Hd.
Assembling Universal Caster System (continued) Swivel Caster Assembly Locating Parts 1. From the bag labeled "Caster" remove the following hardware: 4 Hex Head Bolts, 5/16-18 x 5/8" Long 4 Lockwashers, 5/16" External Type 5 Hex Nuts, 5/16-18 1 Hex Lock Nut 5/16-18 1 Button Head Bolt 5/16-18 x 1" 1 Hex Head Bolt 5/16-18 x 4-1/4 2. From the caster carton find the following: 1 Swivel Caster 1 Hinge Plate 1 Center Frame w/Actuator Hex Hd.
3. Hold the hinge plate with the caster in the center of the frame as shown. Slide the 5/16-18 x 4-1/4 bolt through frame and hinge plate. Finger tighten lock nut. Tighten nut with a 1/2" and adjustable wrench but do not over tighten. The hinge plate should freely pivot inside the frame. NOTE: The hinge plate can be mounted in either set of holes as shown. 5/16-18 Lock Nut Alternate Mounting Location 5/16-18 x 4-1/4 Bolt 4.
Assembling Universal Caster System To Saw Locating Parts 1. From the bag labeled "Caster" remove only the following hardware: 8 Hex Jam Nut, 3/8-16 4 3/8 Spring Lockwasher 8 Washer, 3/8 x 7/8 x 5/64 4 Foot Leveling Leveling Foot WARNING: If your saw has damaged or missing parts, they must be repaired or replaced before this assembly can be completed. Reference your saw owner’s manual or Authorized Service Department if necessary.
Leveling Feet Adjustment 1. Adjust fixed wheel caster frame leveling feet so that the saw is resting on two wheels. The leveling feet should not touch the floor and should be adjusted about 3/4" from the bottom of the end frame to the bottom of the foot as shown. Tighten all nuts using 9/16" wrench. 3/4" Fixed Wheel Frame 2. Adjust the swivel caster frame leveling feet so that the saw does not rock when the swivel caster is disengaged and the saw is resting on these two feet and the two fixed wheels.
Assembly Mounting Your Saw 1. From the bag labeled “Legs” remove the following hardware: 4 Hex Head Screws, 5/16-18 x 1-1/4" Long 4 Hex Nuts, 5/16-18 4 Lockwashers, 5/16" External Type 8 Flat Washers, 11/32 x 11/16 x 1/16 2. Place the saw upside down onto a smooth piece of cardboard or heavy paper, on the floor, so the saw is resting on the table top. 5/16-18 x 1-1/4 In Hex Head Screw 5/16-18 Hex Nut 5/16 In External Lockwasher WARNING: The saw is heavy.
Assembling Table Extensions 1. From the bag labeled “Table Extensions” remove the following hardware: (Quantity indicated is for two extensions) 8 Hex Head Screws, 5/16-18 x 1-1/4" Long 8 Flat Washers, 11/32 x 11/16 x 1/16 8 Lockwashers, 5/16" External Type 8 Hex Nuts, 5/16-18 NOTE: Assemble with saw upside down. 5/16-18 x 1-1/4 In Hex Head Screw WARNING: Stock table extensions must be installed. They help support the fence guide bars. An unsupported guide bar can twist.
Assembly (continued) Checking Table Insert WARNING: To reduce the risk of injury from accidental start, make sure switch is “OFF” and plug is not connected to power source outlet. Table Insert 1. Insert should be flush with table top. Check as shown. Loosen flat head screw that holds insert and adjust the four set screws as necessary. Tighten flat head screw. Do not tighten screw to the point where it bends the insert. CAUTION: Insert must be even with the table surface.
Checking Heeling Adjustment or Parallelism of Sawblade to Miter Gauge Groove While cutting, the material must move in a straight line parallel to the sawblade. Therefore, both the miter gauge groove and the rip fence must be parallel to the sawblade. Sawblade WARNING: The blade must be parallel to the miter gauge groove. Misaligned blades could bind on workpiece. Workpiece could suddenly kickback. You could be cut or hit.
Assembly (continued) Checking Blade Tilt, or Squareness of Blade to Table Tilt Lock Handle When the bevel pointer is pointing directly to the “0” mark on the bevel scale, the sawblade should make a square cut 90° to the table. WARNING: For your own safety, turn switch “OFF” and remove plug from power source outlet. To check for squareness, 90° position. 1. Raise blade to 3" depth of cut. 2. Operate the tilt lock handle (counterclockwise) to loosen the tilt clamp screw.
B. If blade is not square to table...the 90° stop screw must be adjusted. 1. Unscrew 90° stop screw three to four turns using 3/16 inch hex “L” wrench. 2. Turn tilt handwheel clockwise one turn, then turn handwheel counterclockwise until blade is square with table. 3. Screw 90° stop screw in until it stops. Check once again for squareness and readjust screw, if necessary. 4. Check pointer as described in step A. 90° Stopscrew To check for alignment, 45° Position 1. Tilt blade to left as far as it will go.
Assembly (continued) Installing Front Rip Fence Guide Bar 1. From the bag labeled “Guide Bars” remove only the following hardware: 5 Square Head Bolts, 5/16-18 x 1" Long 5 Lockwashers, 5/16 External Type 5 Flat Washers, 21/64 x 5/8 x 1/16 5 Hex Nuts, 5/16-18 2. From the fence guide bar carton find the following: 1 Front Guide Bar (Long) 3. Insert five 5/16-18 x 1” long square head bolts into the holes as shown. 4.
Installing Rear Fence Guide Bar 1. From the bag labeled “Guide Bars” remove only the following hardware: 5 Square Head Bolts, 5/16-18 x 1" Long 5 Lockwashers, 5/16 External Type 5 Flat Washers, 21/64 x 5/8 x 1/16 5 Hex Nuts, 5/16-18 2. From the fence guide bar carton find the following: 1 Rear Guide Bar (Short) 3. Insert five 5/16-18 x 1” long square head bolts into the holes as shown. 4.
Assembly (continued) Adjusting Rip Fence Guide Bars WARNING: Front and rear guide bars must be aligned with blade. Misaligned guide bars could twist. Twisted guide bars could misalign fence. A misaligned fence could cause binding or kickback. You could be hit or cut. Very Thin Shim Washer Installing Shims 1. From the bag labeled “Guide Bars” remove the following hardware: *10 Very thin shim washers. 2. Loosen the 5 nuts holding the rear guide bar in place. 3.
Rip Fence Alignment Adjustment WARNING: A misaligned fence can cause kickbacks and jams. To reduce the risk of injury, follow these instructions until the fence is properly aligned. 1. The rip fence must be PARALLEL with the sawblade and miter gauge grooves. Clean any debris off the fence guide bars. Move fence until it is along side the miter gauge groove and lock it. It should be parallel to groove. If it is not: a. Unlock fence. b.
Assembly (continued) Installing Blade Guard 1. From the bag labeled “Blade Guard” remove the following parts: 2 Hex Head Screws, 1/4-20 x 5/8" Long 2 Hex Nuts, 1/4-20 2 Lockwashers, 1/4 External Type 1 Thumb Screw 1 Spreader Support From the blade guard carton find the following: 1 Blade Guard 1/4-20 x 5/8 In Hex Hd Screw 1/4 In. External 1/4-20 Hex Nut Lockwasher Thumb Screw Spreader Support 2. Slide spreader support onto spreader rod until notches engage pin.
Aligning Blade Guard 1. Lay blade of square or other straightedge alongside of blade. 2. Loosen socket set screw in guard support and move spreader left or right so that it touches blade of square. Tighten screw. Socket set screw must tighten against the spreader rod flat. NOTE: The spreader is now square with the table and approximately in line with the sawblade. The spreader requires further adjustment to align it parallel to the blade and in the middle of the cut (kerf) made by the sawblade.
Assembly (continued) Mounting the Motor 1. Remove Motor Assembly from motor carton. 2. Loosen the two hex head screws that lock the pins in the cradle. 3. Lift motor and insert the two pins on motor support assembly into holes in cradle. Push motor in as far as it will go. Do not tighten screws at this time. Motor Pins Hex Head Screws Motor Support Assembly Cradle Installing Belt 1. Locate the motor belt 2. Lower the blade all the way down and set bevel to 0°. 3.
7. Put your hand around the belt half way between the two pulleys and squeeze belt until two sides of belt touch. The motor should move freely as you squeeze the belt. If motor does not move freely, belt tension must be readjusted. Installing Belt Guard 1. From the bag labeled “Miscellaneous” remove the following hardware: 4 Hex Nuts, 10-32 8 Flat Washers, 13/64 x 3/8 x 1/32. From among the loose parts find the following: 1 Belt Guard Press Down on Tab Lock To Open 13/64 I.D.
Assembly (continued) Mounting Switch and End Caps 1. From the bag labeled “Miscellaneous” remove only the following hardware: 2 Pan Head Screws, 10-32 x 3/8" Long 2 Lockwashers, #10 External Type 2 Square Nuts, 10-32 4 Pan Head Screws, Type “AB” 8 x 1/2" Long 2 Rear Stop Washers From the bag labeled “Trim” remove the following: 4 Plastic End Caps 1 Key Switch 2. Insert the 2 10-32 x 3/8" pan head screws with lockwashers through the outermost holes in switch assembly. 3.
Getting to Know Your Table Saw 6 Miter Gauge 7 Blade Guard 9 Sawblade 5 Rip Fence 10 Ind-I-Cut 8 Table Insert 2 Elevation Wheel 11 Micro-Adjust Rip Fence 1 On-Off Switch 12 Casters 13 Miter Gauge and Rip Fence Storage Hooks 1. On-Off Switch. CAUTION: Before turning switch “ON”, make sure the blade guard is correctly installed and operating properly. The On-Off Switch has a locking feature. This feature is intended to help prevent unauthorized and possible hazardous use by children and others. A.
Getting to Know Your Table Saw (continued) 2. Elevation Handwheel...elevates or lowers the 6. Miter Gauge...head is locked in position for cross blade. Turn clockwise to elevate, counterclockwise to lower. Tilt Handwheel...tilts the blade for bevel cutting. Turn clockwise to tilt toward left, counterclockwise to tilt toward right. When the blade is tilted to the left as far as it will go, it should be at 45° to the table and the bevel pointer should point 45°.
9. Removing and Installing Sawblade Lo os en WARNING: To reduce the risk of injury from accidental start, turn switch “OFF” and remove plug from power source outlet before removing or installing sawblade. A. Raise blade guard, remove insert. B. To remove blade, place a block of wood against front of blade, pull arbor wrench toward you to loosen arbor nut. C. To tighten arbor nut, place a block of wood against rear of blade, push wrench away from you.
Getting to Know Your Table Saw (continued) 11. Micro-Adjust Rip Fence...allows the operator to accurately adjust the rip fence using only one hand. To move the fence push in on the micro-adjust knob and rotate. Micro Adjust Knob 12. Universal Caster System The caster system is activated by rotating the handle 180° to engage the swivel caster, lifting the one side of the saw off the floor. The handle can be operated by hand or foot.
Safety Instructions for Basic Saw Operations Before Each Use • Replace damaged or missing parts before using the saw again. • Use the sawblade guard, spreader and anti-kickback pawls for any thru-sawing (whenever the blade comes through the top of the workpiece). Make sure the antikickback pawls work properly. Make sure the spreader is in line with sawblade. • Remove adjusting keys and wrenches. Form a habit of checking for and removing keys and wrenches from table top before turning saw on.
Safety Instructions for Basic Saw Operations (continued) Plan Ahead To Protect Your Eyes, Hands, Face and Ears Dress for safety • Do not wear loose clothing, gloves, neckties or jewelry (rings, wrist watches). They can get caught and draw you into moving parts. • Wear nonslip footwear. • Tie back long hair. • Roll long sleeves above the elbow. • Noise levels vary widely. To reduce the risk of possible hearing damage, wear ear plugs or muffs when using table saw for hours at a time.
Work Feed Devices Before cutting any wood on your saw, study all of the “Basic Saw Operations”. As you learn new table saw woodworking techniques, you’ll see that many types of cuts need different support and feeding devices, known as jigs or fixtures. They can help you make cuts more accurately. By helping to steady the workpiece and keep you away from the blade, they can help you safely use your saw for certain cuts. Many people custom build their own jigs and fixtures.
Work Feed Devices (continued) Making the handle: • Miter crosscut a piece of 3/4 inch thick plywood to shape and size shown: NOTE: The mitered corners can be any size that looks like the drawing (about 1-1/2" by 1-1/2"). Putting it Together • Using good quality woodworking glue, glue the 3/8" x 3/8" x 2-1/2" piece strip saved earlier to the base as shown. IMPORTANT: Do not use nails or screws. This is to prevent dulling of the sawblade in the event you cut into the push block.
Basic Saw Operations • An auxiliary wood facing attached to the miter gauge can help prevent workpiece twisting and throwbacks. Attach it to the slots provided. Make the facing long enough and big enough to support your work. Make sure, however, it will not interfere with the sawblade guard. • Use jigs or fixtures to help hold any piece too small to extend across the full length of the miter gauge face during the cut.
Basic Saw Operations (continued) Crosscutting (continued) Lock Knob Slots are provided in the miter gauge for attaching an auxiliary facing to make it easier to cut very long or short pieces. Select a suitable piece of smooth wood, drill two holes through it and attach with screws. Make sure the facing does not interfere with the proper operation of the sawblade guard. When cutting long workpieces, you can make a simple support by clamping a piece of plywood to a sawhorse. (As seen on previous page.
Miter Crosscutting Miter cutting is known as cutting wood at an angle other than 90° with the edge of the wood. Follow the same procedure as you would for crosscutting. • Adjust the miter gauge to the desired angle, and lock it. • The miter gauge may be used in either of the grooves in the table. Make sure it is locked. • When using the miter gauge in the left hand groove, hold the workpiece firmly against the miter gauge head with your left hand, and grip the lock knob with your right hand.
Basic Saw Operations (continued) Using the Rip Fence • A featherboard can help guide the workpiece. (See “Basic Saw Operation-Using Featherboards for ThruSawing” section.) • Always use featherboards for any non thru-sawing rip type cuts. (See “Basic Saw Operations-Using Featherboards for Non Thru-sawing” section) Before Starting: • To reduce the risk of kickbacks and slips into the blade, make sure the rip fence is parallel to the sawblade. • Before thru-sawing, check the anti-kickback pawls.
Once the trailing end is on the table: Push Stick When “width of rip” is 2” or wider, use the push stick to finish the work all the way past the blade. When “width of rip” is narrower than 2” the push stick cannot be used because the guard will interfere...use the auxiliary fence and push block. Attach auxiliary fence to rip fence with two “C” clamps. Auxiliary Fence Feed the workpiece by hand along the auxiliary fence until the end is approximately 1” past the front edge of the table.
Basic Saw Operations (continued) WARNING: To reduce the risk of injury from blade contact never thru-saw cuts narrower than 1/2” wide. Baffle Narrow strips thicker than the auxiliary fence/work support may enter the guard and strike the baffle. Carefully raise guard only enough to clear the workpiece. Use push block to complete cut. Bevel Ripping Narrow Work When bevel ripping material 6” or narrower, use fence on the right side of the blade only.
Using Featherboards for Non Thru-Sawing Work Support Featherboards are not employed during non thru-sawing operations when using the miter gauge. Use featherboards for all other non thru-sawing operations (when sawblade guard must be removed). Featherboards are used to keep the work in contact with the fence and table as shown and to stop kickbacks. Add a 7-1/2” high flat facing board to the fence, the full length of the fence.
Basic Saw Operations (continued) Using Carbide Tipped Blades Before using a carbide tipped blade, always examine the blade and tips for damage. Look for bent teeth, a bent blade, cracks, broken, missing or loose carbide tips. Do not use a carbide tipped blade if damage is found or suspected. Do not use a carbide tipped blade without all appropriate guards in place. Mount blade securely in proper rotation direction. Never rotate a carbide tipped blade faster than its maximum recommended speed.
Rabbeting Second Cut Rabbeting is known as cutting out a section of the corner of a piece of material, across an end or along an edge. To make a rabbet requires cuts which do not go all the way through the material. Therefore, the blade guard must be removed. 1. Remove blade guard. 2. For rabbeting along an edge (long way of workpiece) as shown add facing to rip fence approximately as high as the workpiece is wide.
Basic Saw Operations (continued) Molding Molding is cutting a shape on the edge or face of the workpiece. With a molding head and a selection of different knife shapes it is possible for almost any kind of molding (base, cove, bead, etc.) to be produced. There are a wide variety of molding heads available as well as many different shapes of knives. Be sure and consult the specific instructions included with your molding head.
Adjustments WARNING: For your own safety, turn switch “OFF” and remove plug from power source outlet before making any adjustments. Knob Miter Gauge Head Miter Gauge NOTE: The graduations are manufactured to very close tolerances which provide ample accuracy for fine woodworking. In some cases where extreme accuracy is required, when making angle cuts, for example, make a trial cut and then recheck it.
Maintaining Your Table Saw Maintenance Anti-Kickback Pawl WARNING: For your own safety, turn switch “OFF” and remove plug from power source outlet before maintaining or lubricating your saw. Spreader • Do not allow sawdust to accumulate inside the saw. Frequently blow out any dust that may accumulate inside the saw cabinet and the motor. • Clean your cutting tools with a gum and pitch remover. • The cord and the tool should be wiped with a dry clean cloth to prevent deterioration from oil and grease.
RIDGID Recommends the Following Accessories Item SKU No. Molding/Dado Insert for 7 In. Dia. Molding or Dado Head......................................................AC1025 Dust Collector .....................................................AC1098 Caster System ....................................................AC1050 Miter Gauge ........................................................AC1021 Do not use any accessory unless you have received and read complete instructions for its use.
Troubleshooting (continued) Motor NOTE: Motors used on wood working tools are particularly susceptible to the accumulation of sawdust and wood chips and should be blown out or “Vacuumed” frequently to prevent interference with normal motor ventilation. Trouble Probable Cause Remedy Excessive Noise 1. Motor 1. Have motor checked by qualified service technician. Repair service is available at your nearest Authorized Service Center. Motor fails to develop full power.
Repair Parts Parts List for RIDGID 10 Inch Table Saw Model TS24240 Figure 1 - ON-OFF Power Outlet 10 9 7 1 2 3 9 4 8 11 5 6 7 Always Order by Part Number - not by Key Number Key No. 1 2 3 4 5 6 7 8 9 10 11 Part No. 822150-1 * * 826121 826123 826122 * 826452 826450 826451 63467 Description Bracket, Switch Housing Lockwasher #10 Nut Hex 10-32 Box Switch Switch Locking Key Switch Screw, Pan Hd.
35 36 34 30 Repair Parts Parts List for RIDGID 10 Inch Table Saw Model No.
Repair Parts Parts List for RIDGID 10 Inch Table Saw Model No. TS24240 Figure 2 Always Order by Part Number - not by Key Number Key No. 59 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Part No.
Repair Parts Parts list for RIDGID 10 Inch Table Saw Model No.
Always Order by Part Number - not by Key Number Key No. 61 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Part No.
Repair Parts Parts List for RIDGID 10 Inch Table Saw Model No. TS24240 Figure 4 - Fence Assembly 1 10 2 3 9 4 6 7 11 5 12 8 13 14 37 39 15 13 16 38 34 36 17 18 19 33 35 32 20 21 31 30 29 28 27 22 23 24 25 26 Always Order by Part Number - not by Key Number Key No. Part No. Key No. Description 1 809492-7 Screw Pan Hd. Ty “T” 8-32 x 1 2 824350-1 Cap Channel Rear 3 Nut Lock 5/16-18 * 4 Washer 21/64 x 5/8 x 1/16 * 5 Screw Pan Hd.
Repair Parts Parts List for RIDGID 10 Inch Table Saw Model No. TS24240 Figure 5 - Miter Gauge Assembly 1 2 14 3 4 13 12 5 6 7 11 10 8 9 Always Order by Part Number - not by Key Number Key No. — 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Part No. 826661 826506 * 826663 * 123069-1 824573-1 824570 * * 818470-4 826662 * * 818471-6 Description Miter Gauge, Complete Knob Washer 8 x 23 x 1.8 Gauge, Miter Screw, Pan Hd.
Repair Parts Parts List for RIDGID 10 Inch Table Saw Model No. TS24240 Figure 6 - Guard Assembly 1 4 5 3 2 1 12 7 11 1 6 7 1 6 8 10 9 8 Always Order by Part Number - not by Key Number Key No. — 1 2 3 4 5 6 7 8 9 10 11 12 Part No. 826519 60208 62391 803528-1 826466 62390 * 62520 813146-1 804845-1 62410 * 62519 Description Guard Asm.
Repair Parts Parts List for RIDGID 10 Inch Table Saw Model No. TS24240 Figure 7 - Leg Set 3 11 2 2 4 12 1 7 6 6 12 13 14 7 3 5 2 1 9 8 6 1 7 8 6 7 1 10 Key No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Part No. Description 805589-5 826113 826116 826115 509511 Screw, Serrated Truss Head.
Repair Parts Parts List for RIDGID Universal Caster System Model No.
Repair Parts Parts List for RIDGID Universal Caster System Model No. TS24240 Always order by part number - Not by key number Key No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Part No. 825899 * * 826824 * 825904-1 805589-5 826594 805466-13 60484 * 806481-1 * * 825898 825905-1 803835-2 * * * * * * * 825910 825902 825901 * 825903-1 Description Actuator Caster Nut Hex 1/4-20 Lockwashers 1/4 Handle Caster Screw Hex Hd. 1/4-20 x 3/4 Frame Caster End Screw Truss Hd.
Lifetime Warranty On RIDGID Tools The RIDGID REPUTATION is the result of the consistent product quality and years of pride in workmanship. Rigorous checks and controls from raw materials to packaged products insure product confidence widely accepted as the mark of the professional trades. Therefore, RIDGID covers its products with a LIFETIME WARRANTY against defects in material or workmanship.
