User Manual

ManualsBrandsRidetech ManualsCar41240000

350 S. St. Charles St. Jasper, In. 47546

Ph. 812.482.2932 Fax 812.634.6632

www.ridetech.com

TGR14000 68-72 GM “A” Body TigerCage

Basic Cage

1 T129-1 Main Hoop

1 T101D-1 Driver side hoop mount

1 T101P-1 Passenger side hoop floor mount

2 T105 Hoop to frame mount (inner, front)

1 T097D Driver side hoop to frame mount (inner, rear)

1 T097P Passenger side hoop to frame mount (inner, rear)

1 T092D Driver side hoop to frame mount (outer)

1 T092P Passenger side hoop to frame mount (outer)

1 T130-1 Driver side package tray bar

1 T131-1 Passenger side package tray bar

2 T095 Package tray reinforcement plate

1 T132-1 Driver side trunk bar

1 T133-1 Passenger side trunk bar

2 T103 Trunk bar to frame mount

2 T002 Clamp tabs

1 T037P TigerClamp P (threaded)

1 T038P TigerClamp P

1 T037D TigerClamp D (threaded)

1 T038D TigerClamp D

1 Tube of Anti-Seize

1 ENG34115 Polyurethane body mount kit

Hardware:

16 3/8” x 1” USS Gr. 8 SHCS Clamps / Main hoop to mount

46 3/8” x 1 ¼” USS Gr. 8 bolt Mounting brackets

12 3/8” x 1” self-tapping screws Mounting brackets

46 3/8” USS Gr.8 Nylok nut Mounting brackets

12 3/8” Lock washer Mounting brackets

104 3/8” SAE flat washer Mounting brackets

2 ½” x 1 ½” 12 point Gr. 8 bolt Bar to clamp tab

2 ½” Flange nut Bar to clamp tab

T101 T097 T092 T105 T095 T103

Summary of content (6 pages)

PAGE 1
350 S. St. Charles St. Jasper, In. 47546 Ph. 812.482.2932 Fax 812.634.6632 www.ridetech.com TGR14000 68-72 GM “A” Body TigerCage Basic Cage 1 1 1 2 1 1 1 1 1 1 2 1 1 2 2 1 1 1 1 1 1 T129-1 T101D-1 T101P-1 T105 T097D T097P T092D T092P T130-1 T131-1 T095 T132-1 T133-1 T103 T002 T037P T038P T037D T038D Tube of Anti-Seize ENG34115 Hardware: 16 46 12 46 12 104 2 2 3/8” x 1” USS Gr. 8 SHCS 3/8” x 1 ¼” USS Gr. 8 bolt 3/8” x 1” self-tapping screws 3/8” USS Gr.
PAGE 2
TGR14000 Installation Instructions • • • • • • • Initial fitment of the floor mount brackets must be done under the carpet. Final installation can be done under or over the carpet. Use Anti-Seize on all fasteners that are threaded into stainless clamps or brackets. Install all bars before final tightening. Always tighten the tab side of the clamp first. Torque all 3/8” fasteners to 45 ft-lbs and all 1/2” fasteners to 75 ft-lbs.
PAGE 3
7. The hoop mount ties into the outside of the frame rail with this bracket. Two 3/8” Nylok nuts with flat washers will fasten it to the floor and four 3/8” x 1” self-tapping screws will secure it to the frame rail. Use a 5/16”’ bit to pre-drill the holes. 8. Bolt the main hoop to the floor mounts using four 3/8” x 1” socket head cap screws. 9. In order to keep the “T” in the casting facing up, and the bolts facing the correct direction, there are two different direction clamps.
PAGE 4
14. Drop four 3/8” x 1 ¼” bolts with flat washers down through the bar mount and the holes in the package tray. 15. Fasten the trunk bar to the package tray bar with four 3/8” Nylok nuts and flat washers. 16. Using the trunk bar as a template drill two 3/8” holes through the vertical surface of the package tray. 17. Place the reinforcement plate on the inside of the package tray and secure with assembly with two 3/8” x 1 ¼” bolts, flat washers and Nylok nuts. Nuts should face the trunk. 18.
PAGE 5
20. Secure the frame bracket to the floor pan with four 3/8” Nylok nuts and flat washers. 21. Using the bracket as a template; drill four 3/8” holes through the frame rail. Fasten the bracket to the frame with four 3/8” x 1 ¼” bolt, Nylok nuts and flat washers. 22. You may now tighten all clamps and bolts.
PAGE 6