User guide

ManualsBrandsRidetech ManualsCar41162000

350 S. St. Charles St. Jasper, In. 47546

Ph. 812.482.2932 Fax 812.634.6632

www.ridetech.com

Part #41162000

67-69 Camaro TigerCageRoad Race Door Bar Kit

Door Bars

1 41162901 (T052-1) Driver side road race style door bar assembly

1 41162900 (T053-1) Passenger side road race style door bar assembly

1 41162904 (T028D) Driver side door bar floor mount

1 41162903 (T028P) Passenger side door bar floor mount

2 41160910 (T024) Door bar floor mount reinforcement plate (under car)

2 41162902 (T043) Door bar floor mount reinforcement plate (kick panel)

4 49990005 (T002) Clamp tab

2 49990003 (T037P) TigerClamp P (threaded)

2 49990001 (T038P) TigerClamp P

2 49990004 (T037D) TigerClamp D (threaded)

2 49990000 (T038D) TigerClamp D

1 Tube of Anti-Seize

Hardware:

16 3/8” x 1” USS SHCS Clamps

12 3/8” x 1” USS Gr. 8 bolt Door bar to mount / Door bar mount to kick panel

8 3/8” x 1 ¼” USS Gr. 8 bolt Door bar mount through floor

8 3/8” lock washer Door bar to mount

24 3/8” SAE flat washer Door bar mount

12 3/8” USS Gr. Nylok nut Door bar mount

4 ½” x 1 ½” 12 point Gr. 8 bolt Bar to clamp tab

4 ½” Flange nut Bar to clamp tab

T028D/P Door Bar Floor Mount T002 TigerClamp Tab T043 Kick Panel Plate T024 Under Car Plate

Summary of content (4 pages)

PAGE 1
350 S. St. Charles St. Jasper, In. 47546 Ph. 812.482.2932 Fax 812.634.6632 www.ridetech.com Part #41162000 67-69 Camaro TigerCageRoad Race Door Bar Kit Door Bars 1 1 1 1 2 2 4 2 2 2 2 1 41162901 41162900 41162904 41162903 41160910 41162902 49990005 49990003 49990001 49990004 49990000 Tube of Anti-Seize Hardware: 16 12 8 8 24 12 4 4 3/8” x 1” USS SHCS 3/8” x 1” USS Gr. 8 bolt 3/8” x 1 ¼” USS Gr. 8 bolt 3/8” lock washer 3/8” SAE flat washer 3/8” USS Gr. Nylok nut ½” x 1 ½” 12 point Gr.
PAGE 2
TGR10002 Installation Instructions • • • • • • • Initial fitment of the floor mount brackets must be done under the carpet. Final installation can be done under or over the carpet. Use Anti-Seize on all fasteners that are threaded into stainless clamps or brackets. Install all bars before final tightening. Always tighten the tab side of the clamp first. Torque all 3/8” fasteners to 45 ft-lbs and all 1/2” fasteners to 75 ft-lbs.
PAGE 3
. Assemble the clamps to the main hoop. Use clamp P on the driver side and clamp D on the passenger side. Tighten the clamp enough to be able to position it. 4. Use the ½” x 1 ½” 12 point bolt & flange nut to fasten the door bars to the clamps. 5. Temporarily bolt the floor mount to the door bar using 3/8” x 1” bolts, lock washers and flat washers. 6. Slide the door bar down the main hoop until the floor mount contacts the floor. The lower bar should also be parallel to the floor pan. Tighten the clamps.
PAGE 4
10. Two more 3/8” holes must be drilled into the kick panel. Install the reinforcement plate and secure the bracket with 3/8” x 1” bolts, flat washers and Nylok nuts. 11. Reinstall the door bars.