User Manual

ManualsBrandsRidetech ManualsCar41160000

350 S. St. Charles St. Jasper, In. 47546

Ph. 812.482.2932 Fax 812.634.6632

www.ridetech.com

Part # 41160000

67-69 Camaro TigerCage

Basic Cage

1 41160904 (T046-1) Main hoop assembly

2 41160909 (T025-1) Main hoop mount

2 41160908 (T029) Main hoop reinforcement plate (inside car)

2 41260910 (T013) Main hoop reinforcement plate (under car)

2 49990002 (MISC1011) 1 ¼” plastic plug for rocker panel

1 41160903 (T047-1) Driver side package tray bar

1 41160902 (T048-1) Passenger side package tray bar

2 41160905 (T044) Package tray reinforcement plate

1 41160901 (T049-1) Passenger side trunk bar

1 41160900 (T050-1) Driver side trunk bar

2 41160906 (T032) Trunk bar reinforcement plate (under car- outer)

2 41160907 (T031) Trunk bar reinforcement plate (under car- inner)

2 49990005 (T002) Clamp tab

1 49990003 (T037P) TigerClamp P (threaded)

1 49990000 (T038P) TigerClamp P

1 49990004 (T037D) TigerClamp D (threaded)

1 49990001 (T038D) TigerClamp D

1 Tube of Anti-Seize

Hardware:

16 3/8” x 1” USS Gr. 8 SHCS Clamps / Main hoop to mount

4 3/8” x 1” USS Gr.8 bolt Main hoop mount reinforcement plate to pinch weld

12 3/8” Lock washer Hoop to lower mount mount/ lower mount to plate

32 3/8” x 1 ¼” USS Gr. 8bolt Main hoop mount to reinforcement plates/ trunk bars

32 3/8” USS Gr.8 Nylok nut Main hoop mount reinforcement plates

68 3/8” SAE flat washer Main hoop mount / trunk bars

2 ½” x 1 ½” 12 point Gr. 8 bolt Bar to clamp tab

2 ½” Flange nut Bar to clamp tab

T025-1 Main Hoop Mount T044 Package Tray Plate T031 Trunk Bar Plate-Inner T032 Trunk Bar Plate- Outer

T013 Hoop Plate- Under T029 Hoop Plate- Inside T002 TigerClamp Tab MISC1011 1 ¼” Plug

Summary of content (8 pages)

PAGE 1
350 S. St. Charles St. Jasper, In. 47546 Ph. 812.482.2932 Fax 812.634.6632 www.ridetech.
PAGE 2
TGR10000 Installation Instructions • • • • • • • Initial fitment of the floor mount brackets must be done under the carpet. Final installation can be done under or over the carpet. Use Anti-Seize on all fasteners that are threaded into stainless clamps or brackets. Install all bars before final tightening. Always tighten the tab side of the clamp first. Torque all 3/8” fasteners to 45 ft-lbs and all 1/2” fasteners to 75 ft-lbs.
PAGE 3
. The upper portion of the bracket will fasten to the wire trough with a reinforcement plate inside the trough. A 1 ¼” access hole must be drilled (¾” in front of the bracket and 7/8” from the top of the trough) to slide the reinforcement plate through. Use 3/8” x 1 ¼” bolts, flat washers and lock washers to secure the bracket. A plastic plug is supplied to cover the access hole. 4. Fasten the main hoop to the mounts using 3/8” x 1” Socket Head Cap Screws and nd lock washers. washers 5.
PAGE 4
7. In order to keep the “T” in the casting facing up, and the bolts facing the correct direction, there are two different direction clamps. Be very careful as to which clamp halves you are bolting together. Refer to the image on page 6 for clamp locations. 8. A correctly assembled clamp should look like the one in the picture shown to the left; there should be a gap on one side for the tab to slide into. 9. The next bar to be installed is the package tray bar. 10.
PAGE 5
13. The long opening next to the drilled holes has a lip that will interfere with the trunk bar mount. The lip must be flattened; this can be done with a pair of pliers. 14. Bolt the trunk bar mount up to the package tray, use 3/8” Nylok nut and flat washers to secure the assembly. 15. Two 3/8” holes must be drilled through the vertical plane of the package tray to install the reinforcement plate. These holes must be drilled from the trunk.
PAGE 6
16. The other end of the trunk bar will attach to the trunk floor, straddling the frame rail. 17. Two more reinforcement plates will be installed under the car, one on each side of the frame rail. Six 3/8” x 1 ¼” bolts, flat washers and Nylok nuts will be used.
PAGE 7
TigerClamp Location Chart
PAGE 8
Package Tray Bar Template