User guide

ManualsBrandsRidetech ManualsCar11406799

350 S. St. Charles St. Jasper, In. 47546

Ph. 812.482.2932 Fax 812.634.6632

www.ridetech.com

Part # 11406799

92-99 Tahoe / Yukon Rear AirBar

4 Door Only

Components:

2 90009000 Tapered sleeve air spring

2 90000002 Upper air spring frame bracket

1 90000062 Air spring frame plate assembly

1 90000063 Air spring frame plate

2 90000064 Frame bracket assembly

2 90000989 Lower bar – TW24.75” (C-C 26.50”)

2 90000990 Upper bar – TW26.50” (C-C 28.25”)

1 90000943 Panhard bar – TT30.25” (C-C 34.25”)

4 90001584 Threaded rod end – 3/4" thread x 5/8” I.D.

8 90001942 Rubber bushing – Pressed into bars & rod ends

2 90001589 Kevlar rod end – panhard bar

1 90000067 Panhard bar axle bracket assembly

2 90000042 Upper axle bracket assembly

2 90000037 Lower axle bracket assembly

2 90001082 Short bump stop

1 99010031 Hardware kit

Summary of content (5 pages)

PAGE 1
350 S. St. Charles St. Jasper, In. 47546 Ph. 812.482.2932 Fax 812.634.6632 www.ridetech.com Part # 11406799 92-99 Tahoe / Yukon Rear AirBar 4 Door Only Components: 2 90009000 Tapered sleeve air spring 2 90000002 Upper air spring frame bracket 1 90000062 Air spring frame plate assembly 1 90000063 Air spring frame plate 2 90000064 Frame bracket assembly 2 90000989 Lower bar – TW24.75” (C-C 26.50”) 2 90000990 Upper bar – TW26.50” (C-C 28.25”) 1 90000943 Panhard bar – TT30.25” (C-C 34.
PAGE 2
350 S. St. Charles St. Jasper, In. 47546 Ph. 812.482.2932 Fax 812.634.6632 www.ridetech.com Tahoe Fastener kit = 6 3/8 x 3/4 uss bolt 2 3/8 uss nyloc nut 8 3/8 sae flatwasher 8 3/8 lockwasher 8 7/16 x 1 1/4 uss bolt 16 7/16 flatwasher 8 7/16 uss nyloc nut 10 1/2 x 1 3/4 uss bolt 2 1/2 x 2 1/2 uss bolt 10 1/2 flatwasher 12 1/2 uss nyloc nut 2 1/2 x 4” sae Gr. 8 bolt 2 1/2 sae Gr. 8 nyloc nut 4 1/2 sae Gr. 8 flatwasher 8 5/8 x 7” sae Gr. 8 bolt 8 5/8 sae Gr. 8 nyloc nut 16 5/8 sae Gr.
PAGE 3
50 S. St. Charles St. Jasper, In. 47546 Ph. 812.482.2932 Fax 812.634.6632 www.ridetech.com 92 to 99 4 Dr. Tahoe /Yukon 1. Support truck at comfortable working height using jackstands under the frame. 2. Support the rear axle with a floor jack. 3. Remove 1 leafspring assembly. [Removing 1 at a time will prevent having to chase the rearend across the shop!] 4. Remove the front leafspring frame hangar by drilling or grinding the attaching rivits. 5. Install the AirBar frame bracket.
PAGE 4
9. The next step is to install the passenger side airspring frame plate. This plate also locates the frame end of the panhard bar. It is indexed by the tailpipe hangar holes in the framerail. 10. The additional upper airspring bracket holes are then marked and drilled to 7/16” 11. Attach the upper airspring bracket using [4] 7/16” x 1 1/4 bolts and nyloc nuts. If you ARE NOT installing a C notch, the legs of the bracket will point up. If you ARE installing a C notch, the legs will point down.
PAGE 5
This a view of the passenger side airspring mounting. The upper mount is approx 1” below the top of the frame. Also note that the bed support that is directly above the axle must be notched for clearance. This is a view of the drivers side airspring mount and panhard bar mount. Note that the panhard bar mount may be welded if desired. Also note that the airspring mounts will come into alignment when the axle is raised into ride height position.