Manual

ManualsBrandsRidetech ManualsCar11330199

350 S. St. Charles St. Jasper, In. 47546

Ph. 812.482.2932 Fax 812.634.6632

www.ridetech.com

Part # 11330199

63-72 C-10 Level 1 Air Suspension System

Front Components:

1 11331099 Front CoolRide Kit for Stock Lower Arms

1 11330509 RQ Series Front Shock Kit w/ Mounts

Rear Components:

1 11334099 Rear CoolRide Kit

1 11330709 RQ Series Rear Shocks

Compressor System:

1 30154000 3 gallon RidePro Compressor Kit (Analog Gauges)

Summary of content (11 pages)

PAGE 1
350 S. St. Charles St. Jasper, In. 47546 Ph. 812.482.2932 Fax 812.634.6632 www.ridetech.
PAGE 2
350 S. St. Charles St. Jasper, In. 47546 Ph. 812.482.2932 Fax 812.634.6632 www.ridetech.com Part # 11331099 63-87 Chevy C10 Front CoolRide Kit For Use w/ Stock Lower Arms Components: 2 90006873 Front air springs – 224C 2 90000060 Upper air spring plate 2 90000057 Lower air spring cup bracket 2 90001083 Medium bump stops – 1.
PAGE 3
Installation Instructions 1. Raise and support truck at a safe, comfortable working height. Let the front suspension hang freely. 2. Remove coil spring, shock absorber and bump stop. Refer to factory service manual for proper disassembly procedure. 3. Hold the upper plate to the cross member as shown in the picture to the left and clamp to frame. Using the plate as a template drill 4 holes in the cross member. 4. Apply thread sealant to the air fitting and thread into the air spring.
PAGE 4
350 S. St. Charles St. Jasper, In. 47546 Ph. 812.482.2932 Fax 812.634.6632 www.ridetech.com Part # 11330509 63-72 C-10 RQ Series Front Shock Kit For Use w/ Stock Lower Arms Shock: 2 22539999 RQ Smooth Body Shock Cartridge 4 70011138 ¾” ID Shock Bushing 2 90002102 1/2” ID Inner Sleeve 2 90002103 5/8” ID Inner Sleeve Components: 2 90001619 Shock Stud Hardware: 2 99501003 ½”-13 x 2 ½” Hex Head Bolt 2 99502001 ½”-13 Nylok Nut Installation Instructions 1.
PAGE 5
350 S. St. Charles St. Jasper, In. 47546 Ph. 812.482.2932 Fax 812.634.6632 www.ridetech.
PAGE 6
Installation Instructions 1. Raise the vehicle to a safe and comfortable working height with the suspension hanging freely. 2. Remove the coil spring and shock absorbers. 3. Apply thread sealant to a 90 degree air fitting and screw it into the top of the air spring. Note: When using larger fittings you may need to trim the bracket and/or frame rail. 4. Place the upper mount over the studs on the air spring. Secure with two 3/8” Nylok nuts and flat washers. 5.
PAGE 7
350 S. St. Charles St. Jasper, In. 47546 Ph. 812.482.2932 Fax 812.634.6632 www.ridetech.
PAGE 8
350 S. St. Charles St. Jasper, In. 47546 Ph. 812.482.2932 Fax 812.634.6632 www.ridetech.com ARC4000 Compressor System Instructions These are some general guidelines to follow when installing your new RidePro air control system. Depending on the vehicle there are many different ways to plumb the system. Start out by planning a lay out of where you want everything to be mounted.
PAGE 9
Mounting the RidePro Air Valves       The valves, like the compressor, are sealed and can be mounted in the same locations. Although if the vehicle will be exposed to freezing temperatures it is a good idea to mount them in the engine bay if possible to reduce the possibility of freezing. They can be mounted in any position. Mount the valves higher than the tank to avoid moisture build up. This could cause the air pressure sensors to give a faulty reading.
PAGE 10
ARC4000 Wiring at control panel: Gray connects to gauge light Red connects to “key on” power at fuse box
PAGE 11
Relay Wiring Diagram