Manual

350 S. St. Charles St. Jasper, In. 47546

Ph. 812.482.2932 Fax 812.634.6632

www.ridetech.com

11329100 78-88 GM “G” Body

Front MuscleBar

Components:

1 90001825 Front sway bar (37.125”)

1 90001821 Driver side arm

1 90001822 Passenger side arm

2 90001819 Frame plate

2 90001820 Frame bracket

2 90000926 10 mm 90 degree PosiLink

2 90000924 10 mm Straight PosiLink

2 90001823 PosiLink Spacer (2.5”)

4 90000717 T-bushing (PosiLink to lower arm)

2 90001099 Polyurethane frame bushing

2 99250001 ¼” - 28 straight grease zerk

1 90001092 Tube of Lithium grease

2 99115009 10mm x 1.5 x 90mm stud (use Loctite) In PosiLink

Hardware Kit: 99010049

2 99111001 10 x 1.5 x 30mm Flat head Allen bolt Frame plate to frame

2 99111002 10 x 1.5 x 30mm bolt Frame bracket

4 99373003 3/8” SAE flat washer Frame bracket

4 99373005 3/8” lock washer Frame bracket

2 99373007 3/8” x 1” Self-tapping screws Frame bracket

6 99371017 3/8” x 1” Button head Allen bolt Sway bar arm to bar

6 99373003 3/8” SAE flat washer Sway bar arm to bar

6 99373005 3/8” lock washer Sway bar arm to bar

4 99112002 10mm Nylok nut PosiLink

4 99373003 3/8” flat washers PosiLink

PDF created with pdfFactory trial version www.pdffactory.com

PAGE 1
350 S. St. Charles St. Jasper, In. 47546 Ph. 812.482.2932 Fax 812.634.6632 www.ridetech.com 11329100 78-88 GM “G” Body Front MuscleBar Components: 1 1 1 2 2 2 2 2 4 2 2 1 2 90001825 90001821 90001822 90001819 90001820 90000926 90000924 90001823 90000717 90001099 99250001 90001092 99115009 Front sway bar (37.125”) Driver side arm Passenger side arm Frame plate Frame bracket 10 mm 90 degree PosiLink 10 mm Straight PosiLink PosiLink Spacer (2.
PAGE 2
11329100 Installation Instructions 1. This sway bar was designed for use with our lower StrongArms. Installation with other control arms may require modification. 2. Remove the end links from the factory sway bar. Then remove the bolts attaching the sway bar to the frame. 3. Bolt the frame plate to the frame using the factory sway bar holes. The front hole will use a 10mm x 30mm flat head Allen screw. The rear hole will use a standard 10mm x 30mm hex bolt. 4.
PAGE 3
7. Bolt the sway bar arm to the bar using 3/8” x 1” Button head screws with flat washers and lock washers. 8. Fasten the 90 degree end of the PosiLink to the sway bar arm using a 10mm Nylok nut and flat washers Note: There are two holes in the sway bar arm. For Shockwave and CoolRide arms use the front hole. For coils spring arms use the rear hole. 9. Two T-bushing will be used on each side to attach the straight end of the PosLink to the lower control arm. Secure with a 10mm Nylok nut. 10.