INDEX sensibleness Easter area sass area sees 2 2. Film wind up screensavers Hl 3. Sprocket reverse stop. 4. 45° micro ...canniness 5. Focusing of finder. 6. F stop indication .. 7. Meter switch ON, OFF Shutter scale needle 9. Electric equipment 10. Body back 1. DISASSEMBLING OF MAJOR COMPONENT PARTS... 1 Finder Cover 2. Sodom tssrsansrernestersateranraatss 1. 8. conciseness 14 oversensitiveness saris 15 Shh Aww www ® 5. WIRING 19 2, advertisements 6. ASA 20 7. SCHEMATIC DIAGRAM 8.
CAMERA TYPE FILM FORMAT STANDARD LENSES LENS MOUNT SHUTTER VIEWFINDER FOCUSING EXPOSURE METER SPECIFICATIONS Rico X-1 35 mm SLR with metal focal plane shooter. 24 x36 Nondrinker {/1.4 (Multi-coated), & groups 7 elements 50 mm XR Nondrinker {71.7 (Multi-coated), $ groups 6 elements 50 mm XR Nondrinker 5 groups 6 elements Filter size: $2 mm screw-in type “K™ type bayonet with 65° rotating angle. Vertically moving Opal CF-523 metal focal plane shutter with speeds from 1 to 1/1000 sec. plus B.
Following tool sets are recommended for dis-reassembling. 1) For the ME-BUTTON HOLDER (sketch N3. 13 on page 22). 2} For the FILM WIND UP LEVER NUT (sketch No. 2 on page 22). 3} For the FINDER COVER NUT (sketch No. 6 on page 22). 4) For the SHUTTER SPEED DIAL SCREW (sketch No. 7 on page 22). 5) For the ASA PLATE NUT (sketch No. 23 on page 22). 6) For the ASA BUTTON NUT (sketch No. 20 on page 22). 7 For the SYNCHRONY SOCKET (sketch No. 26 on page 22). 1.
Detach the soldered portions of the LEAD WIRES (blue, pink) coming from the resistor plate. Take off four SCREWS (sketch No. 49 and 50 on page 24) as well as the EYEPIECE FRAME (sketch No. 48) on page 24. Take off three SCREWS (sketch No. 1) as well as ASA BASE PLATE ASS'Y (sketch No. 2) and ASA CONTACT ASS’Y (sketch No. 3). Take off the SCREW (sketch No. 5) Detach the soldered portion of ASA RESISTOR PLATE ASS'Y (sketch No, 6). Take off two SCREWS (sketch No. 3 on page 24).
2. ASSEMBLING Mirror box (sketch No, 1 on page 32) Set the SELF-TIMER to its regular position. Carefully set the micro box in the main body. Set it so that the RELEASE LEVER becomes as indicated by a circle in Fig. 13. After ascertaining that the mirror box has been completely mounted, fasten it to the main body with five SCREWS {sketch Nao. 21 and 22 on page 24). Wind the FILM WIND UP LEVER, and confirm that the shutter works properly.
NOTE: 1} In case the difference of the shutter dial bulb position and that of the SPEED INDICATOR CAM bulb is one pitch or more, follow the instructions of NOTE {page 5), and re-engage them. 2) In case there is a slight difference in the position of the shutter dial bulb and that of the speed indicator cam blab, adjust by loosening the screw of A in Fig. 1, turn the eccentric screw of B. {Do not forget to tighten screw A after this adjustment.) 3) Fig.
3. GENERAL MECHANISM * §. Quick returns mechanism (see Fig. 7, Sand 9) 1) When the wind up lever is wound, the shutter is set. 3) The rear blade lever of the shutter kicks No. 13 when the At the same time, No, | moves in the arrow direction and vanes are closed. catches interlocked with No. 13 actuates No. 6 which then Then, No. 2 is set in No. 4 while No. 3 is set in No. 5. (Fig. 7) releases No. 1. 2) When the release button is depressed, No. 7 acts, pushing No. No. 2 and No. 3 operate simultaneously. No.
2. Multi exposure mechanism (Fig. 10 and 11) Fig. 10 shows the condition when ME button has not been depressed. When the film wind up lever is wound under such condition, the winding clutch lever catches the part of gear A (5) marked with an arrow, and turns the gear. At the same time, the sprocket interlocked with the gear turns and advances the film. & Gear A @ Winding clutch button Fig. 10 @ ME lever J Winding clutch lever 2) Fig. 11 indicates the condition in which the ME button has been depressed.
3. Light measuring mechanism (Fig. 12) The camera has a built-in TTL system interlocking exposure meter with three CdS cells instated on both sides and on top of the eye lens. The applicable film sensitivity is ASA 12 ~ 3200, the interlocking function range of the exposure meter (ASA 100) and the power source is a sitter-oxide battery which is contained in the battery box on the bottom of the body. ! lens Pena prism CdS Meter eT" Condenser fens Fg.
4. ADJUSTMENT n 2) Release stroke When exchanging the mirror box or when it is necessary to adjust the release stroke, proceed as follows: Adjust by changing the width of the release lever of Fig. 13. The scope of adjustment of the release stroke is indicated in Fig. 14. Film wind up (sce Fig. 15) When changing the film wind up shaft ass’y or related parts, check and make necessary adjustments. Release button SNe Foe —-02 Fig. 13 Fig.
3. Sprocket reverse stop (see Fig. 16) In case the relative position between the film perforation and sprocket teeth becomes uneven, or when related pairs have been exchanged, check and make necessary adjustments. How 10 adjust: When the film wind up lever is wound and sel, turn the ECCENTRIC SHAFT so that the STOPPER of the lever A enters the bottom of the GEAR B. C, regardless of the minimum and maximum winding. After finishing adjustment, tighten the SCREW.
Accusing of finder When finder is-out of focus. Remove the BOTTOM COVER and adjust with SCREW shown by an arrow in Fig. 19. How io adjust. When finder focus is too long, turn clockwise. (Tightening direction) When finder focus is too short, turn counter-clockwise, {Loosening direction) Sequence of checking when finder is owt of focus. Check whether the lens unit correctly focuses or not.
Meter switch ON, OFF When the film wind up lever is set ta locking position, power is turned to OFF. (Fig. 22} When power is OFF, the CONTACT PIECE A must be between the CONTACT PIECE B and the CONTACT PIECE C. ’ If the CONTACT PIECE A touches some part, bend and insulate it. When power is ON, the CONTACT PIECE A touches the CONTACT PIECE 8B. When there is no contact, bend the CONTACT PIECE A and adjust properly. (Fig. 23) 8.
9. 2) Electric equipment When changing electric parts and when adjustment is necessary, do as follows. Adjustment of CdS (use the Digital Multi Meter) (Fig. 25) When adjusting CdS, use the light sources of LVS and LVOV. 1} Adjust to 27.30 ki? 10.7 at VR4 with LV9. 2) Adjust to 15.58 k2 $0.06 at VR3 with LVOV, NOTE: 1) When not changing electric parts, absolutely refrain from touching or moving VR3 and VR4 for adjusting Cds.
3) Checker adjustment (Fig. 25) a) Checker is adjusted at VR1. 1) Adjust checker with VRI, turning the release holder clockwise, so that the Meier needle enters the battery checker of Fig. 27. NOTE: 1) The point where the upper tip of the meter needle and the lower tip of the battery checker mark touch is 3.03v. 2) The indication of the battery used is 15V x but as the actual capacity is 3.1V, checker adjustment is 3.
S. WIRING DIAGRAM Resistor plate Synchrony contact Green C$ circuit board Shutter dial cam © (® B, Exposure meter ed Light blue.
8. SKETCH INDEX AND PARTS LIST A. Top and front parts Ln Parts represented by the encircled consecutive numbers arc also deliverable as assembly pasts.
Sketch No. Part No.
B. Mirror box and viewfinder parts C3 33 34 Parts represented by the encircled consecutive numbers are also deliverable as assembly parts.
Sketch No. Part No. Description i 31161862 Adhesive tape 2 31161310 Shield 3 02517035W Screw 31161306 Prism cover 5 3161311 F stop prism holder 6 31161312 F stop prism 7 31161347 Prism 8 31161309 Shield : prism 9 02417020W Screw M1.
C. Prism frame and shutter dial parts Parts represented by the encircled consecutive numbers are also deliverable as “assembly parts.
Sketch No. Part No. Description 1 624170702 Screw MLT x 7.0 2 31161015 ASA base plate ass’y 3 31161040 ASA contact says 4 31161680 Screw 5 025140302 Screw M1.4x 30 é 31161072 ASA resistor plate says 1 024140252 Screw ML4 x 2.5 8 024170302 Screw M17 x 3.
Sketch No. Part No. Description 1 02520070Z Screw M2.0 x 7.0 2 31161016 Strap metal 3 31161101 Body 4 31161464 Latch ; back cover 5 31161466 Clip cover 6 02414030W Screw M1.4 x 3.0 7 31161465 Shari : back cover latch 8 31161469 Screw : film guide 9 31163008 Screw 10 3it61488 Shield "n 62517045E Screw M17 x 4.5 12 31161128 Shaft 13 361127 Slipper : reverse rotation " 31161129 Spring 15 31161426 Washer 1% 31161416 Rewinding shaft 17 02470302 Screw M1.
® Part No, Sketch No. Description 1 31161701 Shutter says 2 020200302 Screw M2.0 x 3.0 3 31163005 Shield 4 31161186 $ stopper 5 31161187 Shield plate 6 31164586 Front leather : left 7 02417020W Screw M17 x 2.0 8 31161490 Plate 9 31161928 Orange wire 0 31161687 Screw i 31161483 Contact : battery case 12 02417035W Screw M1.7x 2.
Sketch No. Part No.
9. PARTS INDEX Pant Nov Description Sketch No. 31161001 Film wind up fever SSS AS 3161004 Battery cover cuss's FE 19~21 31161006 Pressie plate ass’y D560 31161010 ASA contact says ca 3161015 ASA base plate ass'y C2 311610th Strap metal D2 31161017 Sp oat 036 31161018 Mail fever E3§ 3161019 Gears B.C.
Part No. Description Sketch No.
Part No. Description Sheikh No. 31161907 Power contact cn 31161908 Checker contact C18 31161929 Strange wire E$ 31162801 Body cap A32 31163003 Screw A-10 31163004 Screw AT, BH 31163005 Shield E3 ET¥ 4 Sean Dy 31021201 Synergy rocket A-26 31121503 Accessory shoe A-19 31131026 Self ever ass’y F4 31131159 Screw E29 31131202 Shoe spring A117 3snn Screw : sell lever E3 02017022W Screw MI1.7 x22 F4l 02017030W Screw M1.7x 30 8-40, D-27, E-27 020170352 Screw M1.7x3.5 E-23 02017055W Screw M17 x 5.
