R3111x Series Low Voltage Detector Product Manual

ManualsBrandsRicoh ManualsRadar DetectorR3111x Series

R3111x SERIES

LOW VOLTAGE DETECTOR

NO.EA-056-080131

OUTLINE

The R3111x series are CMOS-based voltage detector ICs with high detector threshold accuracy and ultra-low

supply current, which can be operated at an extremely low voltage and is used for system reset as an example.

Each of these ICs consists of a voltage reference unit, a comparator, resistors for detector threshold setting,

an output driver and a hysteresis circuit. The detector threshold is fixed with high accuracy internally and does

not require any adjustment.

Three output types, Nch open drain “L” type, Nch open drain “H” type and CMOS type are available.

The R3111x Series are operable at a lower voltage than that for the Rx5VL series, and can be driven by a

single battery.

Six types of packages, TO-92, SOT-89, SOT-23-3, SOT-23-5, SC-82AB, and SON1612-6 are available.

FEATURES

• Supply Current ......................................................................Typ. 0.8µA (−VDET=1.5V, VDD=−VDET−0.1V)

• Range of Operating Voltage Range......................................0.7V to 10.0V (T

opt=25°C)

• Detector Threshold Range....................................................0.9V to 6.0V

• Accuracy Detector Threshold................................................±2.0%

• Temperature-Drift Coefficient of Detector Threshold ............Typ. ±100ppm/°C

• Output Types.........................................................................Nch Open Drain “L”, Nch Open Drain “H”, and

CMOS

• Packages ..............................................................................TO-92, SOT-89, SOT-23-3, SOT-23-5,

SC-82AB, SON1612-6

APPLICATIONS

• CPU and Logic Circuit Reset

• Battery Checker

• Window Comparator

• Wave Shaping Circuit

• Battery Back-up Circuit

• Power Failure Detector

Summary of content (44 pages)

PAGE 1
R3111x SERIES LOW VOLTAGE DETECTOR NO.EA-056-080131 OUTLINE The R3111x series are CMOS-based voltage detector ICs with high detector threshold accuracy and ultra-low supply current, which can be operated at an extremely low voltage and is used for system reset as an example. Each of these ICs consists of a voltage reference unit, a comparator, resistors for detector threshold setting, an output driver and a hysteresis circuit.
PAGE 2
R3111x BLOCK DIAGRAMS R3111xxxxA VDD R3111xxxxB OUT Vref OUT Vref GND R3111xxxxC VDD OUT Vref GND 2 VDD GND
PAGE 3
R3111x SELECTION GUIDE The package type, the detector threshold, the output type and the taping type for the ICs can be selected at the users’ request. The selection can be made with designating the part number as shown below; R3111xxxxx-xx-x ← Part Number ↑ ↑↑↑ ↑ ↑ a b cd e f Code a b c d e f Contents Designation of Package Type; D: SON1612-6 E: TO-92 H: SOT-89 N: SOT-23-5, SOT-23-3 Q: SC-82AB Setting Detector Threshold (−VDET); Stepwise setting with a step of 0.1V in the range of 0.9V to 6.
PAGE 4
R3111x PIN CONFIGURATIONS TO-92 SOT-89 SOT-23-3 3 (mark side) (mark side) 1 1 2 2 3 SOT-23-5 5 4 (mark side) (mark side) 1 1 2 2 3 SC-82AB 4 3 SON1612-6 6 2 1 2 3 PIN DESCRIPTIONS TO-92 SOT-89 4 SOT-23-3 Pin No. Symbol Pin No. Symbol Pin No. Symbol 1 VDD 1 OUT 1 OUT 2 GND 2 VDD 2 GND 3 OUT 3 GND 3 VDD SOT-23-5 SC-82AB 4 (mark side) (mark side) 1 5 SON1612-6 Pin No. Symbol Pin No. Symbol Pin No.
PAGE 5
R3111x ABSOLUTE MAXIMUM RATINGS Symbol VDD Item Rating Unit 12 V VSS−0.3 to VDD+0.3 V VSS−0.
PAGE 6
R3111x ELECTRICAL CHARACTERISTICS • Symbol Item Conditions Min. Typ. Max. Unit −VDET Detector Threshold 0.882 0.900 0.918 V VHYS Detector Threshold Hysteresis 0.027 0.045 0.063 V 0.8 0.9 2.4 2.7 µA 10 V ISS Supply Current VDDH Maximum Operating Voltage VDDL Minimum Operating Voltage∗Note1 IOUT Output Current (Driver Output Pin) tPLH ∆−VDET/ ∆Topt • Topt=25°C R3111x09xA/C VDD=0.80V VDD=2.90V Topt=25°C < = < = −40°C Topt 85°C Nch VDS=0.05V,VDD=0.70V VDS=0.50V,VDD=0.
PAGE 7
R3111x • Symbol Item Conditions Min. Typ. Max. Unit −VDET Detector Threshold 2.646 2.700 2.754 V VHYS Detector Threshold Hysteresis 0.081 0.135 0.189 V 0.9 1.1 2.7 3.3 µA 10 V ISS Supply Current VDDH Maximum Operating Voltage VDDL Minimum Operating Voltage∗Note1 IOUT tPLH ∆−VDET/ ∆Topt • Topt=25°C R3111x27xA/C Output Current (Driver Output Pin) VDD=2.60V VDD=4.70V Topt=25°C −40°C < = Topt < = 85°C Nch VDS=0.05V,VDD=0.70V VDS=0.50V,VDD=1.50V Pch VDS=−2.1V,VDD=4.
PAGE 8
R3111x • Symbol Item Conditions Min. Typ. Max. Unit −VDET Detector Threshold 4.410 4.500 4.590 V VHYS Detector Threshold Hysteresis 0.135 0.225 0.315 V 1.1 1.3 3.3 3.9 µA 10 V ISS Supply Current VDDH Maximum Operating Voltage VDDL Minimum Operating Voltage∗Note1 IOUT tPLH ∆−VDET/ ∆Topt • Topt=25°C R3111x45xA/C Output Current (Driver Output Pin) VDD=4.34V VDD=6.50V Topt=25°C −40°C < = Topt < = 85°C Nch VDS=0.05V, VDD=0.70V VDS=0.50V, VDD=1.50V Pch VDS=−2.1V,VDD=8.
PAGE 9
R3111x • Symbol Item Conditions Min. Typ. Max. Unit −VDET Detector Threshold 2.254 2.300 2.346 V VHYS Detector Threshold Hysteresis 0.069 0.115 0.161 V 0.9 1.1 2.7 3.3 µA 10 V ISS Supply Current VDDH Maximum Operating Voltage VDDL Minimum Operating Voltage∗Note1 IOUT Output Current (Driver Output Pin) tPLH Output Delay Time∗Note2 ∆−VDET/ ∆Topt • Topt=25°C R3111Q231B Detector Threshold Temperature Coefficient VDD=2.2V VDD=4.
PAGE 10
R3111x TIMING CHART Supply Released Voltage +VDET Voltage Detector Threshold -VDET (VDD) Detector Threshold Hysteresis Detector Threshold Hysteresis Detector Threshold Hysteresis Minimum Operating Voltage VDDL GND Pull-up Voltage Output Voltage (VOUT) GND tPLH tPLH R3111xxxxA tPLH R3111xxxxB R3111xxxxC DEFINITION OF OUTPUT DELAY TIME Output Delay Time (tPLH) is defined as follows: 1.
PAGE 11
R3111x 11
PAGE 12
R3111x ELECTRICAL CHARACTERISTICS BY DETECTOR THRESHOLD • R3111x09x to R3111x60x Part Number R3111x09xx R3111x10xx R3111x11xx R3111x12xx R3111x13xx R3111x14xx R3111x15xx R3111x16xx R3111x17xx R3111x18xx R3111x19xx R3111x20xx R3111x21xx R3111x22xx R3111x23xx R3111x24xx R3111x25xx R3111x26xx R3111x27xx R3111x28xx R3111x29xx R3111x30xx R3111x31xx R3111x32xx R3111x33xx R3111x34xx R3111x35xx R3111x36xx R3111x37xx R3111x38xx R3111x39xx R3111x40xx R3111x41xx R3111x42xx R3111x43xx R3111x44xx R3111x45xx R3111x46x
PAGE 13
R3111x Output Current 1 *3 IOUT1[mA] Condition Min. Output Current 2 *3 Typ. IOUT2[mA] Condition Min. VDD= 0.05 0.85V VDD= 1.0V Nch VDS=0.05V VDD=0.7V 0.01 0.05 0.2 Typ. Output Delay Time tPLH[µs] Max. Typ. Max. *2 *2 1.0 100 *1 Condition 1 Condition 1 0.55 0.70 Condition 2 Condition 2 0.65 0.80 1.0 Detector Threshold Temperature Coefficient ∆−VDET/∆Topt[ppm/°C] Condition Typ. 0.5 Nch VDS= 0.5V VDD= 1.5V Minimum Operating Voltage VDDL[V] −40°C < = Topt < = 85°C ±100 2.
PAGE 14
R3111x OPERATION • Operation of R3111xxxxA VDD Ra Comparator OUT OUT pin should be pulled-up to VDD or an external voltage level. Rb Vref Nch Tr.1 Rc GND Block Diagram (R3111xxxxA) 1 2 3 4 5 Step Released Voltage +VDET Detector Threshold -VDET A Detector Threshold Hysteresis B Comparator (+) Pin Input Voltage Supply Voltage (VDD) Comparator Output Minimum Operating Voltage VDDL GND Tr.1 Output Tr.
PAGE 15
R3111x • Operation of R3111xxxxB VDD Ra Comparator OUT OUT pin should be pulled-up to VDD or an external voltage level. Rb Vref Nch Tr.1 Rc GND Block Diagram (R3111xxxxB) 1 2 3 Step 1 2 3 Comparator (−) Pin Input Voltage I II I Comparator Output L H L Tr.1 OFF ON OFF ON OFF ON Released Voltage +VDET Detector Threshold -VDET A Detector Threshold Hysteresis B Supply Voltage (VDD) Minimum Operating Voltage VDDL GND Output Tr.
PAGE 16
R3111x • Operation of R3111xxxxC VDD Comparator Ra Pch OUT Rb Vref Nch Tr.1 Rc GND Block Diagram (R3111xxxxC) 1 2 3 4 5 Step 1 2 3 4 5 I II II II I H L Indefinite L H Released Voltage +VDET Detector Threshold -VDET A Detector Threshold Hysteresis B Comparator (+) Pin Input Voltage Supply Voltage (VDD) Comparator Output Minimum Operating Voltage VDDL GND Tr.1 Output Tr.
PAGE 17
R3111x TEST CIRCUITS ISS 5V VDD 470kΩ VDD VIN R3111x Series VIN R3111x Series OUT VOUT OUT GND GND Supply Current Test Circuit Detector Threshold Test Circuit (Pull-up circuit is not necessary for CMOS Output type.) VDD VDD VIN R3111x Series IOUT VIN OUT R3111x Series VDS GND VDS IOUT OUT VDD−VDS GND Nch Driver Output Current Test Circuit Pch Driver Output Current Test Circuit ∗Apply to CMOS Output type only +VDET+2.0V 0.7V GND 5V VDD R3111x Series P.G. ROUT 470kΩ +VDET+2.0V 0.
PAGE 18
R3111x TYPICAL CHARACTERISTICS 1) Supply Current vs. Input Voltage R3111x09xC R3111x27xC 2.0 Topt=85°C Supply Current ISS(µA) Supply Current ISS(µA) 2.5 2.0 1.5 25°C 1.0 -40°C 0.5 Topt=85°C 1.5 25°C 1.0 -40°C 0.5 0.0 0.0 0 2 4 6 Input Voltage VIN(V) 8 0 10 2 4 6 Input Voltage VIN(V) 8 10 R3111x45xC Supply Current ISS(µA) 2.0 Topt=85°C 1.5 25°C 1.0 -40°C 0.5 0.0 0 2 4 6 Input Voltage VIN(V) 8 10 2) Detector Threshold Hysteresis vs. Temperature R3111x09xC R3111x27xC 0.98 0.
PAGE 19
R3111x R3111x45xC Detector Threshold -VDET(V) 4.8 4.7 +VDET 4.6 4.5 -VDET 4.4 -60 -40 -20 0 20 40 60 Temperature Topt(°C) 80 100 3) Output Voltage vs. Input Voltage R3111x09xC R3111x09xA 5V Pull-up 470kΩ 6 1.4 Output Voltage VOUT(V) Output Voltage VOUT(V) 1.6 1.2 1.0 0.8 85°C 0.6 25°C Topt=-40°C 0.4 0.2 0.0 Topt=-40°C 5 4 25°C 3 2 85°C 1 0 0 0.2 0.4 0.6 0.8 1 1.2 Input Voltage VIN(V) 1.4 1.6 0 0.2 R3111x27xC Output Voltage VOUT(V) 3.5 3.0 2.5 2.0 85°C 1.0 25°C 0.5 1.
PAGE 20
R3111x R3111x45xC R3111x45xA 5V Pull-up 470kΩ 6 5 Output Voltage VOUT(V) Output Voltage VOUT(V) 6 4 3 2 85°C 25°C 1 Topt=-40°C 0 0 1 2 3 4 Input Voltage VIN(V) Topt=-40°C 5 25°C 4 85°C 3 2 1 0 5 6 0 1 2 3 4 Input Voltage VIN(V) 5 6 4) Nch Driver Output Current vs. VDS R3111x09xC R3111x09xC Topt=25°C 600 VDD=0.85V 500 400 300 200 0.7V 100 Topt=25°C 300 Output Current IOUT(µA) Output Current IOUT(µA) 700 0 250 VDD=0.8V 200 150 100 0.7V 50 0 0 0.2 0.4 VDS(V) 0.6 0.8 0 0.
PAGE 21
R3111x R3111x45xC R3111x45xC Topt=25°C VDD=4.5V 50 4.0V 40 3.5V 30 3.0V 20 2.5V 2.0V 10 Topt=25°C 300 Output Current IOUT(µA) Output Current IOUT(mA) 60 250 VDD=0.8V 200 150 0.7V 100 50 1.5V 0 0 0 0.5 1 1.5 2 2.5 VDS(V) 3 3.5 4 4.5 0 0.02 0.04 0.06 VDS(V) 0.08 0.1 5) Nch Driver Output Current vs. Input Voltage R3111x27xC 14 800 12 Output Current IOUT(mA) Output Current IOUT(µA) R3111x09xC 900 700 600 500 Topt=-85°C 400 300 25°C 200 100 0 -40°C 0 0.2 0.4 0.
PAGE 22
R3111x 6) Pch Driver Output Current vs. Input Voltage R3111x09xC 1.2 VDS=0.7V 1.0 0.8 0.6 0.5V 0.4 0.2 Topt=25°C 3.5 Output Current IOUT(mA) 1.4 Output Current IOUT(mA) R3111x27xC Topt=25°C 0.0 3.0 VDS=2.1V 2.5 2.0 1.5V 1.5 1.0V 1.0 0.5V 0.5 0.0 0 2 4 6 Input Voltage VIN(V) 8 0 1 2 3 4 5 Input Voltage VIN(V) 6 7 R3111x45xC Topt=25°C Output Current IOUT(mA) 4.5 4.0 3.5 VDS=2.1V 3.0 1.5V 2.5 2.0 1.0V 1.5 1.0 0.5V 0.5 0.
PAGE 23
R3111x R3111x45xA Output Delay Time tP(ms) 100 10 1 tPLH 0.1 0.01 0.001 0.0001 tPHL 0.001 0.01 Load Capacitance COUT(µF) 0.1 8) Output Delay Time vs. Input Pin Capacitance R3111x09xA R3111x27xA 100 Output Delay Time tP(ms) Output Delay Time tP(ms) 100 10 1 tPHL 0.1 0.01 0.001 0.0001 tPLH 0.001 0.01 Input Pin Capacitance CIN(µF) 0.1 10 1 tPLH 0.1 tPHL 0.01 0.001 0.0001 0.001 0.01 Input Pin Capacitance CIN(µF) 0.1 R3111x45xA Output Delay Time tP(ms) 100 10 1 tPLH 0.1 tPHL 0.01 0.
PAGE 24
R3111x TYPICAL APPLICATION • R3111xxxxA CPU Reset Circuit (Nch Open Drain Output) Case 1. Input Voltage to R3111xxxxA is equal to Input Voltage to CPU Case 2.
PAGE 25
R3111x • Voltage level Indicator Circuit (lighted when the power runs out) (Nch Open Drain Output) VDD VDD R3111xxxxA Series OUT GND • Detector Threshold Adjustable Circuit (Nch Open Drain Output) Adjusted Detector Threshold =(−VDET)×(Ra+Rb)/Rb VDD OUT R3111xxxxA Series Ra VDD C + Hysteresis Voltage =(VHYS)×(Ra+Rb)/Rb Rb ∗) If the value of Ra is set excessively large, voltage drop may occur caused by the supply current of IC itself, and detector threshold may vary.
PAGE 26
R3111x TECHNICAL NOTES When R3111xxxxA/B (Nch Open Drain Output Type) is used in Figure A or Figure B, if impedance of Voltage Supply pin, VDD and VDD of this IC is large, detector threshold level would shift by voltage dropdown caused by the consumption current of the IC itself. Released voltage may also shift and delay time for start-up might be generated by this usage.
PAGE 27
PACKAGE INFORMATION • PE-TO-92-0611 TO-92 (SC-43A) Unit: mm PACKAGE DIMENSIONS 5.2 Max. 4.2Max. 4.2 Max. 0.7 0.55Max. 0.6 Max. 0.7 12.7Min. 0.6Max. 0.5Max. 0.55 Max. 12.7 Min. 2.3Max. 5.2Max. 2.3 Max. 5.2 Max. 5.2Max. 0.5 Max. 2.5 +0.4 –0.1 1 2 3 1.27 1 2 3 2.54 TAPING SPECIFICATION 12.7 ±1.0 (Note) When taping is performed,the pins of TO-92 are subjected to a particular forming. 24.7 Max. 19.0±0.5 16.0±0.5 6.0±0.5 1.45 Max. 0.7±0.2 φ4.0±0.2 12.7 ± 0.
PAGE 28
PACKAGE INFORMATION PE-TO-92-0611 POWER DISSIPATION (TO-92) This specification is at mounted on board. Measurement Result (Topt=25°C,Tjmax=125°C) Free Air Power Dissipation 300mW Thermal Resistance θja=(125−25°C)/0.
PAGE 29
PACKAGE INFORMATION • PE-SOT-89-071210 SOT-89 (SC-62) Unit: mm PACKAGE DIMENSIONS 4.5±0.1 1.5±0.1 1.6±0.2 0.1 S 3 2 1.0±0.2 1 S 0.4 7 ±0.1 0.42±0.1 1.5±0.1 2 3 0.4±0.1 Bottom View 0.42±0.1 1.5±0.1 4.0±0.1 2.0±0.05 4.7 5.65±0.05 0.3±0.1 12±0.3 +0.1 ∅1.5 0 1.5±0.1 TAPING SPECIFICATION (T1: Standard Type) 5.0 2.5Max. 8.0±0.1 T1 ∅1.6±0.1 User Direction of Feed TAPING REEL DIMENSIONS (1reel=1000pcs) ∅ 60 +1 0 0 ∅ 180 −1.5 21±0.8 ∅13±0.2 15.4±1.0 13±0.3 2±0.5 1 0.3±0.2 2.
PAGE 30
PACKAGE INFORMATION PE-SOT-89-071210 POWER DISSIPATION (SOT-89) This specification is at mounted on board. Power Dissipation (PD) depends on conditions of mounting on board. This specification is based on the measurement at the condition below: Measurement Conditions Standard Land Pattern Environment Mounting on Board (Wind velocity=0m/s) Board Material Glass cloth epoxy plastic (Double sided) Board Dimensions 50mm × 50mm × 1.6mm Copper Ratio Top side : Approx. 10% , Back side : Approx.
PAGE 31
PACKAGE INFORMATION • PE-SOT-23-5-071228 SOT-23-5 (SC-74A) Unit: mm PACKAGE DIMENSIONS 2.9±0.2 +0.2 1.1 −0.1 1.9±0.2 (0.95) (0.95) 2 0 to 0.1 3 +0.1 0.15 −0.05 0.4±0.1 0.2 Min. 1 2.8–0.3 4 +0.2 1.6 −0.1 5 0.8±0.1 3.2 3.5–0.05 2.0–0.05 8.0–0.3 4.0–0.1 +0.1 φ1.5 0 0.3–0.1 1.75–0.1 TAPING SPECIFICATION 3.3 4.0–0.1 2.0Max. ∅1.1±0.1 TR User Direction of Feed TAPING REEL DIMENSIONS REUSE REEL (EIAJ-RRM-08Bc) (1reel=3000pcs) 2±0.5 21±0.8 ∅60 +1 0 ∅180 0 −1.5 ∅ 13±0.2 11.4±1.
PAGE 32
PACKAGE INFORMATION PE-SOT-23-5-071228 POWER DISSIPATION (SOT-23-5) This specification is at mounted on board. Power Dissipation (PD) depends on conditions of mounting on board. This specification is based on the measurement at the condition below: (Power Dissipation (SOT-23-5) is substitution of SOT-23-6.) Measurement Conditions Standard Land Pattern Environment Mounting on Board (Wind velocity=0m/s) Board Material Glass cloth epoxy plastic (Double sided) Board Dimensions 40mm × 40mm × 1.
PAGE 33
PACKAGE INFORMATION • PE-SOT-23-3-0510 SOT-23-3 (SC-59A) Unit: mm PACKAGE DIMENSIONS 1.4MAX. +0.2 1.1 –0.1 2.9±0.2 0.4±0.1 0.8 3 1 0.2 MIN. 2.8±0.3 1.6±0.2 0 to 0.1 2 (0.95) +0.1 0.16 –0.06 (0.95) 1.9±0.2 3.3 4.0±0.1 2.0MAX. ∅1.1±0.1 TR User Direction of Feed TAPING REEL DIMENSIONS (1reel=3000pcs) 2±0.5 21±0.8 +1 60 0 0 180 –1.5 13±0.2 11.4±1.0 9.0±0.3 3.5±0.05 3.2 2.0±0.05 8.0±0.3 4.0±0.1 ∅ 1.5+0.1 0 0.3±0.1 1.75±0.
PAGE 34
PACKAGE INFORMATION PE-SOT-23-3-0510 POWER DISSIPATION (SOT-23-3) This specification is at mounted on board. Power Dissipation (PD) depends on conditions of mounting on board. This specification is based on the measurement at the condition below: (Power Dissipation (SOT-23-3) is substitution of SOT-23-6.) Measurement Conditions Standard Land Pattern Environment Mounting on Board (Wind velocity=0m/s) Board Material Glass cloth epoxy plactic (Double sided) Board Dimensions 40mm × 40mm × 1.
PAGE 35
PACKAGE INFORMATION • PE-SC-82AB-0512 SC-82AB Unit: mm PACKAGE DIMENSIONS 2±0.2 1.3±0.2 0.3±0.1 (0.7) 0.3±0.1 1 2 0.3±0.1 0.4±0.1 2.1±0.3 3 ±0.2 1.25 −0.1 4 0.3±0.2 0.9±0.1 0 to 0.1 0.16 +0.1 −0.06 0.05 TAPING SPECIFICATION +0.1 ∅1.5 0 4.0±0.1 2.0±0.05 2.6 2.2 4.0±0.1 1.6MAX. ∅1.1±0.1 TR User Direction of Feed TAPING REEL DIMENSIONS (1reel=3000pcs) 2±0.5 21±0.8 +1 60 0 0 180 −1.5 13±0.2 11.4±1.0 9.0±0.3 8.0±0.3 3.5±0.05 1.75±0.1 0.2±0.
PAGE 36
PACKAGE INFORMATION PE-SC-82AB-0512 POWER DISSIPATION (SC-82AB) This specification is at mounted on board. Power Dissipation (PD) depends on conditions of mounting on board. This specification is based on the measurement at the condition below: Measurement Conditions Standard Land Pattern Environment Mounting on Board (Wind velocity=0m/s) Board Material Glass cloth epoxy plactic (Double sided) Board Dimensions 40mm × 40mm × 1.6mm Copper Ratio Top side : Approx. 50% , Back side : Approx.
PAGE 37
PACKAGE INFORMATION • PE-SON1612-6-0510 SON1612-6 Unit: mm PACKAGE DIMENSIONS (0.3) 3 (0.2) 1 1.6±0.05 4 1.2±0.05 6 (0.3) 0.5 0.3TYP. 1.6±0.1 0.6MAX. 0.125±0.055 0.08 0.22±0.05 0.08 M 1.75 3.5±0.05 2.0±0.05 1.1±0.1 1.75 4.0±0.1 1.1MAX. TR User Direction of Feed TAPING REEL DIMENSIONS (1reel=4000pcs) 2±0.5 21±0.8 ∅60 +1 0 ∅180 0 −1.5 ∅ 13±0.2 11.4±1.0 9.0±0.3 8.0±0.3 4.0±0.1 1.5 +0.1 0 0.25±0.1 1.75±0.
PAGE 38
PACKAGE INFORMATION PE-SON1612-6-0510 Power Dissipation (SON1612-6) This specification is at mounted on board. Power Dissipation (PD) depends on conditions of mounting on board. This specification is based on the measurement at the condition below: Measurement Conditions Standard Land Pattern Environment Mounting on Board (Wind velocity=0m/s) Board Material Glass cloth epoxy plactic (Double sided) Board Dimensions 40mm × 40mm × 1.6mm Copper Ratio Top side : Approx. 50%, Back side : Approx.
PAGE 39
MARK INFORMATION ME-R3111E-0310 R3111E SERIES MARK SPECIFICATION • TO-92 (SC-43A) 1 1 2 3 4 5 6 7 8 9 10 11 12 6 to , 5 : Detector Threshold: ex. −VDET=3.
PAGE 40
MARK INFORMATION ME-R3111H-0310 R3111H SERIES MARK SPECIFICATION • SOT-89 (SC-62) to 1 • 1 2 3 4 5 6 5 , 4 6 : Product Code (refer to Part Number vs. Product Code) : Lot Number Part Number vs.
PAGE 41
MARK INFORMATION ME-R3111Nxx1-0310 R3111Nxx1 SERIES MARK SPECIFICATION • SOT-23-5 (SC-74A) 1 • 2 3 1 , 2 : Product Code (refer to Part Number vs. Product Code) 3 , 4 : Lot Number 4 Part Number vs.
PAGE 42
MARK INFORMATION ME-R3111Nxx2-0310 R3111Nxx2x SERIES MARK SPECIFICATION • SOT-23-3 (SC-59A) 1 • 2 3 1 , 2 : Product Code (refer to Part Number vs. Product Code) 3 , 4 : Lot Number 4 Part Number vs.
PAGE 43
MARK INFORMATION ME-R3111Q-070918 • , 2 : Product Code (refer to Part Number vs. Product Code) 3 , 4 : Lot Number 4 1 3 1 2 R3111Q SERIES MARK SPECIFICATION • SC-82AB Part Number vs.
PAGE 44
MARK INFORMATION ME-R3111D-070918 R3111D SERIES MARK SPECIFICATION • SON1612-6 1 • 1 2 3 4 5 6 5 to , 6 4 : Product Code (refer to Part Number vs. Product Code) : Lot Number Part Number vs.