Owner's Manual Network Guide
Table Of Contents
- Network Guide
- TABLE OF CONTENTS
- Manuals for This Machine
- How to Read This Manual
- 1. Getting Started
- 2. Connecting and Setting Up
- 3. Using a Printer Server
- 4. Monitoring and Configuring the Printer
- Using Web Image Monitor
- Using SmartDeviceMonitor for Admin
- Installing SmartDeviceMonitor for Admin
- Changing the Network Interface Board Configuration
- Locking the Menus on the Machine's Control Panel
- Changing the Paper Type
- Managing User Information
- Configuring the Energy Saver Mode
- Setting a Password
- Checking the Machine Status
- Changing Names and Comments
- Load Fax Journal
- Viewing and Deleting Spool Print Jobs
- Managing Address Information
- Using SmartDeviceMonitor for Client
- Remote Maintenance by telnet
- SNMP
- Getting Printer Information over the Network
- Understanding the Displayed Information
- Message List
- 5. Special Operations under Windows
- 6. Appendix
- INDEX
Using a Printer Server
60
3
E
Enter the printer name in the [De-
vice name:] box and a comment in
the [Comment] box, and then click
[Next].
F
Select the [NetWare] check box,
and then click [Next].
G
Click [Bindery mode], enter the file
server name in the [File Server
Name:] box, and then click [Next].
In the [File Server Name:] box, enter
the name of the file server in which
a print server is created. You can
also click [Browse...] to browse
through available file servers.
H
Enter the print server name in the
[Print Server Name:] box, the printer
name in the [Printer Name:] box,
and the print queue name in the
[Print Queue Name] box, and then
click [Next].
• In the [Print Server Name:] box,
enter the name of the NetWare
print server using up to 47 char-
acters.
• In the [Printer Name:] box, enter
the name of the NetWare printer.
• In the [Print Queue Name] box, en-
ter the name of the print queue
to be added to NetWare.
I
Check the settings, and then click
[Next].
The settings are applied, and NIB
Setup Tool quits.
J
Turn the printer off and then on
again.
Note
❒ To check that the configuration
is made correctly, enter the fol-
lowing from the command
prompt.
F:> USERLIST
❒ If the printer works as config-
ured, the name of the print serv-
er appears as a connected user.
❒ If you cannot identify the print-
er you want to configure, check
the printer name with the con-
figuration page printed from
the printer. For details about
printing a configuration page,
see Printer Reference.
❒ If no printer names appear in
the list, match the frame types
of IPX/SPXs for the computer
and printer. Use the [Network]
dialog box of Windows to
change the frame type of the
computer.
Setting Up as a Print Server
(NetWare 4.x, 5/5.1, 6/6.5)
Follow the procedure below to con-
nect the printer as a print server using
NetWare 4.x, NetWare 5/5.1, or Net-
Ware 6/6.5.
Important
❒ When using the printer as a print
server in NetWare 4.x, NetWare
5/5.1, or NetWare 6/6.5, set it to
the NDS mode.
❒ When using NetWare 5/5.1 or
NetWare 6/6.5, set the printer as a
print server.
A
Log on to the file server as a su-
pervisor or supervisor equivalent.
B
Start NIB Setup Tool on the [Start]
menu.
C
Click [Wizard], and then click [OK].
D
Select a printer you want to con-
figure.