Easy Operation Guide M When the Open Cover/Unit Indicator Lights Standard Printing ANT064S ANT070S ANT104S ANT008S or ANT015S or ANT083S ZDCY100E ANT059S B Loading Paper B Clearing Misfeeds Paper Misfeeds in the Paper Feed Section ANT072S ANT074S ANT015E "x + A" j Adding Ink ZFRY010E "x + A + B" ANT060S ANT089S ANT091S ANT092S ANT090S ANT054S TSLH01BE ANT061S TSLH02BE ANT061S C Replacing the Master Roll Paper Wrapped Around the Drum ANT046S "x + B" ANT065S ZFRH250E ZJVH070E TSL
Paper type: OK Prince Eco G100(55kg), Paper Thickness=80 µm // Pages in book=136 // Print scale=81% Gap (when printed at 81% scale) = Pages in book × Paper thickness / 2 = 5.
Paper type: OK Prince Eco G100(55kg), Paper Thickness=80 µm // Pages in book=136 // Print scale=81% Gap (when printed at 81% scale) = Pages in book × Paper thickness / 2 = 5.440000 mm Introduction This manual contains detailed instructions and notes on the operation and use of this machine. For your safety and benefit, read this manual carefully before using the machine. Keep this manual in a handy place for quick reference. Important Contents of this manual are subject to change without prior notice.
C2758608_Platinum3-EN.book Page i Monday, August 31, 2009 2:32 PM TABLE OF CONTENTS Manuals for This Machine ..................................................................................... 1 What You Can Do with This Machine................................................................... 2 How to Read This Manual ..................................................................................... 4 Safety Information ................................................................................
C2758608_Platinum3-EN.book Page ii Monday, August 31, 2009 2:32 PM 3. Printing Functions Printing Functions ............................................................................................... 41 Master Making Density.............................................................................................41 Fine Mode ................................................................................................................42 Preset Reduce/Enlarge ........................................
C2758608_Platinum3-EN.book Page iii Monday, August 31, 2009 2:32 PM When the Master End Indicator (C) Lights and a Message is Displayed ...... 95 Master Feeding Cover is Open ................................................................................95 Master Tray is Not Set Properly ...............................................................................95 When the Master Eject Indicator (k) Lights .....................................................96 When Other Indicators Light.............
C2758608_Platinum3-EN.
C2758608_Platinum3-EN.book Page 1 Monday, August 31, 2009 2:32 PM Manuals for This Machine The following manuals describe the operational procedures of this machine. For particular functions, see the relevant parts of the manual. Note ❒ Manuals provided are specific to machine type. ❖ Easy Operation Guide Describes information about the control panel and basic operations. ❖ Operating Instructions (this manual) Describes operations, functions, User Tools (initial setting, mode setting, etc.
C2758608_Platinum3-EN.book Page 2 Monday, August 31, 2009 2:32 PM What You Can Do with This Machine Below is a quick summary of this machine's features and where to look in this manual for more information. ❖ Basic Procedure See p.30 “Basic Procedure”. ❖ Saving Ink (Economy Mode) See p.45 “Economy Mode”. ❖ Printing per Class (Class Mode) See p.47 “Class Mode (print per class)”. ❖ Printing on Thick or Thin Paper See p.33 “Printing on Thick or Thin Paper”.
C2758608_Platinum3-EN.book Page 3 Monday, August 31, 2009 2:32 PM ❖ Repeating Original onto One Print See p.59 “Repeat”. ❖ Skip Feed/A3 Paper Feed Printing See p.60 “Skip Feed/A3 Paper Feed”. ❖ Printing Secret Documents (Security Mode) See p.61 “Security Mode”. ❖ Making Color Prints See p.65 “Make Color Prints”. ❖ Printing in Two Colors See p.67 “Printing in Two Colors”.
C2758608_Platinum3-EN.book Page 4 Monday, August 31, 2009 2:32 PM How to Read This Manual Symbols This manual uses the following symbols: R WARNING: Indicates important safety notes. Ignoring these notes could result in serious injury or death. Be sure to read these notes. They can be found in the "Safety Information" section. R CAUTION: Indicates important safety notes. Ignoring these notes could result in moderate or minor injury, or damage to the machine or to property. Be sure to read these notes.
C2758608_Platinum3-EN.book Page 5 Monday, August 31, 2009 2:32 PM Safety Information When using this machine, the following safety precautions should always be followed. Safety During Operation In this manual, the following important symbols are used: R WARNING: Indicates a potentially hazardous situation which, if instructions are not followed, could result in death or serious injury.
C2758608_Platinum3-EN.book Page 6 Monday, August 31, 2009 2:32 PM R CAUTION: • After you move the machine, use the caster fixture to fix it in place. Otherwise the machine might move or come down to cause an injury. • If you use the machine in a confined space, make sure there is a continuous air turnover. • Keep the machine away from humidity and dust. Otherwise a fire or an electric shock might occur. • Protect the machine from dampness or wet weather, such as rain and snow.
C2758608_Platinum3-EN.book Page 7 Monday, August 31, 2009 2:32 PM ENERGY STAR Program ❖ ENERGY STAR® Program Requirements for Imaging Equipment This company is a participant in the ENERGY STAR® Program. This machine is compliant with the regulations specified by the ENERGY STAR® Program. The ENERGY STAR® Program Requirements for Imaging Equipment encourage energy conservation by promoting energy efficient computers and other office equipment.
C2758608_Platinum3-EN.book Page 8 Monday, August 31, 2009 2:32 PM Positions of RWARNING and RCAUTION Labels This machine has labels for RWARNING and RCAUTION at the positions shown below. For safety, please follow the instructions and handle the machine as indicated.
C2758608_Platinum3-EN.book Page 9 Monday, August 31, 2009 2:32 PM Guide to Components ANT046S 1. Front cover 7. Paper feed side plate lock lever Open for access to the inside of the machine. Use to lock or unlock the paper feed side plates. 2. Control panel 8. Side tray fine adjusting dial Operator controls and indicators are located here. See p.12 “Control Panel”. Use to shift the paper feed tray sideways. 3. Exposure glass cover (optional) or Set paper on this tray for printing.
C2758608_Platinum3-EN.book Page 10 Monday, August 31, 2009 2:32 PM ANT043S 1. Exposure glass 8. Drum unit Use to set the original. The master is wrapped around this unit. 2. Master eject unit 9. Drum unit lock lever Open to remove the misfed master. Lift to unlock and pull out the drum unit. 3. Master eject box 10. Ink holder Used masters are stored here. Set the ink cartridge in this holder. 4. Paper delivery side plates Use to align the prints on the paper delivery tray. 5.
C2758608_Platinum3-EN.book Page 11 Monday, August 31, 2009 2:32 PM Options Option List Options Model Name Auto Document Feeder (ADF) DF Type 20 Exposure Glass Cover Platen Cover Type 1018 Drum Unit Color Drum Type 20 LG Tape Dispenser Priport Tape Maker Type 20 Printer Controller Printer Unit VC-20 (Non Network Connectable) Printer Unit Type 4545 (Network Connectable) Key Counter – Note ❒ Printer Unit VC-20 and Printer Unit Type 4545 cannot be used at the same time.
C2758608_Platinum3-EN.book Page 12 Monday, August 31, 2009 2:32 PM Control Panel 1 2 3 4 5 23 24 6 7 8 9 10 11 12 13 14 15 31 32 33 34 16 17 18 19 20 21 22 25 26 27 28 29 30 35 BFU008S 1. {Economy} key Press to save ink. See p.45 “Economy Mode”. 2. {Memory/Class} key Press to select Memory or Class mode. See p.47 “Class Mode (print per class)” or p.48 “Memory Mode (print per original)”. 3. {Erase Border} key Press to select erase margins on the prints. See p.44 “Erase Border”.
C2758608_Platinum3-EN.book Page 13 Monday, August 31, 2009 2:32 PM 13. {Clear Modes/Energy Saver} key 25. {Original Type} key • Clear Modes Press to clear the previously entered job settings. • Energy Saver Press to switch to and from Energy Saver Mode p.32 “Energy Saver Mode”. Press to select Text, Photo, Text/Photo, Pale, or Pencil mode. See p.36 “Original Type”. 14. {Proof} key Press to make proof prints. 15. {Master Making} mode select key Press to select the master making mode. 16.
C2758608_Platinum3-EN.book Page 14 Monday, August 31, 2009 2:32 PM Panel Display The panel display shows the machine status, error messages, and function menus. Important ❒ Do not subject the panel display to strong impact or a force equivalent to 30N or more, otherwise it could be damaged. Note ❒ When you select an item on the panel display, it is highlighted (e.g. 100 ). 2 BFU020 1. Menu for the function selected 2.
C2758608_Platinum3-EN.book Page 15 Monday, August 31, 2009 2:32 PM Panel Display Layout The basic elements of the panel display are explained below. Understanding their meaning helps you use this machine's features quickly and easily. ❖ Sample display when selecting the {Reduce/Enlarge} key BFU021 1. Machine status or messages When the {Reduce/Enlarge} key is pressed, the following display is shown. ANT149S 1. Functions and settings available: • Press the {U}{T} keys to select an item.
C2758608_Platinum3-EN.
C2758608_Platinum3-EN.book Page 17 Monday, August 31, 2009 2:32 PM 1. Before Using the Machine Originals Recommended Sizes and Weights of Originals ❖ Metric version Where original is placed Original size Exposure glass Up to A3 ADF Maximum: 297 mm × 432 mm *1 Original weight -52–128 g/m2 Minimum: 105 mm × 128 mm *1 When using an A3 size original, be sure to check the printed paper size and print size, and use the Reduce or Combine functions.
C2758608_Platinum3-EN.book Page 18 Monday, August 31, 2009 2:32 PM Before Using the Machine Non compatible originals for the Auto Document Feeder (ADF) Placing the following types of originals in the ADF can cause paper misfeeds or result in damage to the originals. Place these originals on the exposure glass instead. • Originals other than those specified on p.
C2758608_Platinum3-EN.book Page 19 Monday, August 31, 2009 2:32 PM Print Paper Print Paper The following limitations apply: Paper Size Metric Paper feed tray A3L *1 , B4 JIS L, A4 L, B5 JIS LK, A5 L, B6 JIS L, A6 L Others (Vertical: 90 - 268 mm, Horizontal: 148 - 388 mm) *1 Inch 1 Paper Weight 81/2" × 14" L, 81/2" × 11" L, 47.1 - 209.3 2 51/2" × 81/2" LK, 8" × 13" L g/m , 12.5 - 55.6 lb. Others (Vertical: 3.6" - 10.5", Horizontal: 5.9" - 15.2") For details about how to print on A3L, see p.
C2758608_Platinum3-EN.book Page 20 Monday, August 31, 2009 2:32 PM Before Using the Machine Non-recommended Paper The following types of paper are not recommended for this machine: • Roughly cut paper • Paper of different thickness and types in the same stack • Envelopes heavier than 85 g/m2, 22.6 lb.
C2758608_Platinum3-EN.book Page 21 Monday, August 31, 2009 2:32 PM Print Paper Important ❒ Correct curls in the paper before placing it in the machine. When you cannot correct the paper curl, stack the paper with the curl face down or face up as shown in the illustration. If the paper is curled, it might wrap around the drum or stains might appear.
C2758608_Platinum3-EN.book Page 22 Monday, August 31, 2009 2:32 PM Before Using the Machine Printing Size Maximum print size 1 210 × 355 mm, 8.3" × 14.0" At low temperatures, the maximum print size may be somewhat smaller. Range that cannot be printed The first 5 mm, 0.2" of the leading edge cannot be printed. When using the optional Auto Document Feeder, the first 5 mm, 0.2", of the leading edge as well as the last 2 mm, 0.08", of the trailing edge cannot be printed. Original Print a a: 5 mm, 0.
C2758608_Platinum3-EN.book Page 23 Monday, August 31, 2009 2:32 PM 2. Basics Printing Preparations Using the Paper Feed Tray and Delivery Tray C Load paper into the paper feed tray. Loading Paper A Carefully open the paper feed tray. ANT074S TSLH026E Note ❒ Correct the paper curl before setting the paper. If you cannot do so, stack the paper with the curl face down as shown. B Shift the paper feed side plates lock lever forward. Adjust the side plates to match the paper size.
C2758608_Platinum3-EN.book Page 24 Monday, August 31, 2009 2:32 PM Basics D Make sure that the paper feed side plates touch the paper lightly. Shift the lock lever to its original position. C Lift the paper delivery end plate and move it to match the print paper size. 2 ANT037S TSLY015E D Lift the paper delivery end plate and adjust it to match the paper size. Setting Up the Paper Delivery Tray A Open the paper delivery tray.
C2758608_Platinum3-EN.book Page 25 Monday, August 31, 2009 2:32 PM Printing Preparations Using the side plate guides When printing on A4L, 81/2" × 11"L, B5 JISKLsize paper and thin paper, you should attach the side plate guides to the side plates of the Paper Delivery Tray. Using the side plate guides allows you to properly assemble the printed papers on the Paper Delivery Tray. B Turn the Side Plate Guide to the direction shown by the arrow, and make sure it is fixed.
C2758608_Platinum3-EN.book Page 26 Monday, August 31, 2009 2:32 PM Basics After Printing This section shows you how to return the paper feed tray and paper delivery tray to their original positions. 2 C Close the paper feed tray. Folding the Paper Feed Tray and Delivery Tray A Remove the paper from the paper feed tray. TSLH020E D Move the end plate until the plate handle is flush with the end of the tray. ANT073S The paper feed tray will move down. B Turn off the main switch.
C2758608_Platinum3-EN.book Page 27 Monday, August 31, 2009 2:32 PM After Printing F Move the side plates to the sides, then lower them. 1 2 2 1 ANT036S G Close the tray.
C2758608_Platinum3-EN.book Page 28 Monday, August 31, 2009 2:32 PM Basics Placing Originals When using the exposure glass, place the originals face down. When using the ADF, place the originals face up. C Lower the exposure glass cover. D Adjust print settings as necessary, Placing Originals on the Exposure Glass Placing Originals in the Auto Document Feeder A Lift the exposure glass cover. A Adjust the guide to the original 2 and then press the {Start} key. size.
C2758608_Platinum3-EN.book Page 29 Monday, August 31, 2009 2:32 PM Placing Originals C Adjust print settings as necessary, and then press the {Start} key. Note ❒ If the next original has been placed in the ADF before the machine stops, that original is fed automatically.
C2758608_Platinum3-EN.book Page 30 Monday, August 31, 2009 2:32 PM Basics Basic Procedure When Auto Cycle mode is on, you can process masters and make prints in a single operation. E Press the {Start} key. Note ❒ You can process masters and make prints in a single operation. See p.35 “Auto Cycle”. ❒ If the machine has user codes set, enter your user code using the number keys, and then press the {OK} key. 2 Reference See p.113 “User Code”. A Make sure no previous settings remain.
C2758608_Platinum3-EN.book Page 31 Monday, August 31, 2009 2:32 PM Basic Procedure G Enter the required number of prints using the number keys. -How to operate ❖ To stop the machine during a multiprint run Press the {Clear/Stop} key. ❖ To return the machine to the initial condition after printing Press the {Clear Modes/Energy Saver} key. ANT122S Note ❒ Set a print quantity between 1 (minimum) and 9999 (maximum). 2 ❖ When clearing entered values Press the {Clear/Stop} key. H Press the {Start} key.
C2758608_Platinum3-EN.book Page 32 Monday, August 31, 2009 2:32 PM Basics 2 Energy Saver Mode Auto Reset If the machine has not been operated for a certain period of time after printing, or when you press and hold the {Clear Modes/Energy Saver} key for 3 seconds, the panel display goes off and the machine enters Energy Saver mode. In Energy Saver mode, the machine consumes less electricity. Press the {Clear Modes/Energy Saver} key again, and the machine will return to the ready condition.
C2758608_Platinum3-EN.book Page 33 Monday, August 31, 2009 2:32 PM Printing on Thick or Thin Paper Printing on Thick or Thin Paper When you make prints on thick (127.9 to 209.3 g/m2, 34.0 to 55.6 lb.), standard (52.3 to 127.9 g/m2, 13.9 to 34.0 lb.) or thin (47.1 to 52.3 g/m2, 12.5 to 13.9 lb.) paper, perform the following steps. B Shift the paper feed side plates lock lever forward. Adjust the side plates to match the paper size.
C2758608_Platinum3-EN.book Page 34 Monday, August 31, 2009 2:32 PM Basics When printing onto thin paper A Set the side pads to both sides of the paper feed side plates. Make sure that the paper feed side plates touch the paper lightly. 2 D Shift the lock lever to its original position. Separation Pressure Lever Position A To prevent double feed, adjust the paper separation pressure using the separation pressure lever.
C2758608_Platinum3-EN.book Page 35 Monday, August 31, 2009 2:32 PM Auto Cycle Auto Cycle Using the default settings, you can process masters and make prints in a single operation. This is called "Auto Cycle". E Enter the required number of prints using the number keys. A Make sure the {Auto Cycle} key is 2 lit. ANT122S F Press the {Start} key. ANT125S Note ❒ If it is not lit, press the {Auto Cycle} key. B Place your originals. Reference See p.28 “Placing Originals”.
C2758608_Platinum3-EN.book Page 36 Monday, August 31, 2009 2:32 PM Basics Original Type A Press the {Original Type} key. Select one of the following four types to match your originals: ❖ Text Specify this if the original document consists primarily of text. 2 ❖ Text/Photo If the original document contains a combination of text and photographs, it is printed using the optimum image balance. ❖ Photo Specify this for photographs, pictures, or colored documents.
C2758608_Platinum3-EN.book Page 37 Monday, August 31, 2009 2:32 PM Sample Print and Adjustment Sample Print and Adjustment Once the master making has been completed, it is possible to confirm the print finish before pressing the {Print} mode select key to start the printing process. A Press the {Proof} key. Adjusting the Print Image Position After master making, you can adjust the print image position to suit your needs.
C2758608_Platinum3-EN.book Page 38 Monday, August 31, 2009 2:32 PM Basics A Press the left {Image Position} key to move the image forwards, the right key to move it backwards. Shifting the Image Position to the Right or Left 2 GRLEFT0E ANT137S * Paper feed direction Note ❒ When you shift the image forwards, leave a margin (more than 5 mm, 0.2") at the leading edge. If there is no margin, paper might wrap around the drum and cause a misfeed.
C2758608_Platinum3-EN.book Page 39 Monday, August 31, 2009 2:32 PM Sample Print and Adjustment Note ❒ The image position can be shifted up to about 10 mm, 0.4" each way. Each division on the scale is 2 mm, 0.08". ❒ In A3 Paper Feed Mode, adjust the print position to within ±1 mm, ±0.04" of the center. 2 B Adjust the paper delivery side plates to the print paper position. C Press the {Proof} key to check the image position.
C2758608_Platinum3-EN.book Page 40 Monday, August 31, 2009 2:32 PM Basics Changing the Printing Speed Use the {W} or {V} key to adjust the speed of the machine with the image density and printing paper. Adjust the print speed using the Speed Keys for the following instances: • When the paper type is changed: • Reduce the print speed when printing on thick or thin paper. • When you want to change the print density: • Increase the print speed to lighten the print density.
C2758608_Platinum3-EN.book Page 41 Monday, August 31, 2009 2:32 PM 3. Printing Functions Printing Functions C Press the {Start} key. Master Making Density You can adjust the image density to suit your needs. Note ❒ You can specify the image density that is selected by default when the power is turned on. See “Master Making Density” on p.108 “4 Initial Settings”. A Press the {Master Making Density} key to select the density you want to set.
C2758608_Platinum3-EN.book Page 42 Monday, August 31, 2009 2:32 PM Printing Functions Fine Mode Preset Reduce/Enlarge Use the {Fine} key to make clear prints. Use this function to reduce or enlarge originals by a preset ratio. A Set your originals. B Press the {Fine} key to select Fine mode. 3 GRRATI0E BFU010S C Enter the number of prints with the number keys. Note ❒ You can select a ratio regardless of the size of the original or the printing paper.
C2758608_Platinum3-EN.book Page 43 Monday, August 31, 2009 2:32 PM Printing Functions ❖ Inch version Ratio (%) Original → Print paper size 155 5 1/2" × 8 1/2" → 8 1/2" × 14" 129 5 1/2" × 8 1/2" → 8 1/2" × 11" 121 8 1/2" × 14" → 11" × 17" 93 — 77 8 1/2" × 14" → 8 1/2" × 11" 74 11" × 15" → 8 1/2" × 11" 65 11" × 17" → 8 1/2" × 11", 8 /2" × 11" → 5 1/2" × 8 1/2" 1 ❒ You can specify the reproduction ratio that is selected by default when the power is turned on. See “Ratio” on p.
C2758608_Platinum3-EN.book Page 44 Monday, August 31, 2009 2:32 PM Printing Functions D Enter the number of prints with Erase Border the number keys. This function erases all four margins of the original or paper. ACY068S 3 Note ❒ You can specify within a range of 0 to 20mm, 0" to 0.8", the width of the margin to be erased. See “Erase Border Width” on p.108 “4 Initial Settings”. ANT122S E Press the {Start} key. ❒ The default is 5 mm, 0.2". A Set your original. B Press the {Erase Border} key.
C2758608_Platinum3-EN.book Page 45 Monday, August 31, 2009 2:32 PM Printing Functions D Press the {Start} key. Economy Mode Use this function to save ink. Note ❒ Prints will appear lighter when Economy mode is used. ❒ The default is Off. To select either “On” or “Off” for Economy mode, see “Economy Mode” on p.108 “4 Initial Settings”. A Set your original. B Press the {Economy Mode} key. 3 ANT128S Memory/Class BFU012S C Enter the number of prints with the number keys.
C2758608_Platinum3-EN.book Page 46 Monday, August 31, 2009 2:32 PM Printing Functions ❖ Memory Mode (print per original) You can choose from the following two types of Memory mode: • Normal Memory Mode Use to make prints from a number of different originals. A different number of prints is made from each original.
C2758608_Platinum3-EN.book Page 47 Monday, August 31, 2009 2:32 PM Printing Functions Class Mode (print per class) Note ❒ You can print for up to 24 combinations of number of prints and number of classes. ❒ The maximum possible number of classes in one combination is 99. A Set your original. B Press the {Memory/Class} key. E With the number keys, enter the desired number of classes, and then press the {q} key. Note ❒ Repeat Steps D to E as desired. 3 F Press the {OK} key.
C2758608_Platinum3-EN.book Page 48 Monday, August 31, 2009 2:32 PM Printing Functions Memory Mode (print per original) E Press the {OK} key. F If you are using the optional tape dispenser, turn on the tape dispenser switch. Normal Memory Mode Note ❒ You can make prints from up to 30 originals at one time. A Set your original. B Press the {Memory/Class} key. 3 On Off TSLP013E Note ❒ The optional tape dispenser automatically feeds out strips of paper to separate the prints made from each original.
C2758608_Platinum3-EN.book Page 49 Monday, August 31, 2009 2:32 PM Printing Functions D With the number keys, enter the Stack Memory Mode Limitation ❒ To use Stack Memory mode, you need to first set Memory Mode to “Stack Mode” using the user tools. See “Memory Mode Setting” on p.109 “5 Mode Settings”. Note ❒ You can make prints for up to 30 classes at one time. A Set your original. B Press the {Memory/Class} key. desired number of prints for each class, and then press the {q} key.
C2758608_Platinum3-EN.book Page 50 Monday, August 31, 2009 2:32 PM Printing Functions C Use the {U}{T} keys to select 7 Recall Program Note ❒ You can store up to 10 entries for Memory mode with each entry containing settings for up to 30 originals (Normal Memory mode), or settings for up to 30 classes (Stack Memory mode). ❒ You can store up to 10 entries for Class mode with each entry containing settings for up to 24 combinations of classes and numbers of prints.
C2758608_Platinum3-EN.book Page 51 Monday, August 31, 2009 2:32 PM Printing Functions Storing Stack Memory Mode Settings Limitation ❒ To use Stack Memory mode, you need to first set Memory Mode to “Stack” using the user tools. See “Memory Mode Setting” on p.109 “5 Mode Settings”. A Press the {User Tools} key. D Use the {U}{T} keys to select a number, and then press the {OK} key. Note ❒ If the number is already in use, a message will be displayed asking if you wish to overwrite the settings stored.
C2758608_Platinum3-EN.book Page 52 Monday, August 31, 2009 2:32 PM Printing Functions D Use the {U}{T} keys to select a Storing Class Mode Settings number, and then press the {OK} key. A Press the {User Tools} key. 3 BFU014S B Use the {U}{T} keys to select 4 Initial Settings, and then press the {OK} key. Note ❒ If the number is already in use, a message will be displayed asking if you wish to overwrite the settings stored. To overwrite, press the {OK} key.
C2758608_Platinum3-EN.book Page 53 Monday, August 31, 2009 2:32 PM Printing Functions F Confirm that the settings are cor- Recalling the Stored Settings rect, and then press the {OK} key. A Set your original. B Press the {Memory/Class} key. Note ❒ To change the stored settings, use the {U}{T} keys to select the item that you wish to change, and then overwrite using the number keys. BFU013S C Use the {U}{T} keys to select Re- 3 G Press the {Start} key. call Program, and then press the {OK} key.
C2758608_Platinum3-EN.book Page 54 Monday, August 31, 2009 2:32 PM Printing Functions D Use the {U}{T} keys to select the Class/Year Preparation To use this mode, you need to first register the number of prints required for each class. Registering Class/Year 3 Note ❒ You can register for up to 108 classes (up to 12 classes per school year for a maximum of 9 school years). desired school year, and then press the {OK} key.
C2758608_Platinum3-EN.book Page 55 Monday, August 31, 2009 2:32 PM Printing Functions Printing for All Years Printing for Selected Classes A Set your original. B Press the {Memory/Class} key. A Set your original. B Press the {Memory/Class} key. 3 BFU013S BFU013S C Use C Use D Use the {U}{T} keys to select All D Use the {U}{T} keys to select the the {U}{T} keys to select Class/Year, and then press the {OK} key. Years, and then press the {OK} key.
C2758608_Platinum3-EN.book Page 56 Monday, August 31, 2009 2:32 PM Printing Functions E Use the {U}{T} keys to select the class that you wish to print for, and then press the {q} key. Note ❒ Repeat Step E to select more classes. ❒ You can only select classes from the same school year. ❒ If you have selected the wrong class, highlight it again using the {U}{T} keys, and then press the {q} key to cancel its selection. 3 F Press the {OK} key. G Press the {Start} key.
C2758608_Platinum3-EN.book Page 57 Monday, August 31, 2009 2:32 PM Printing Functions ❒ Any image closer than 5mm, 0.2" to the leading edge of the first original will not be printed. Also, any image closer than 4mm, 0.16" to the leading edge of the second original will not be printed. When the image is too close to the leading edge, make duplicates of the originals with the image shifted away from the leading edge, and then print from the duplicates.
C2758608_Platinum3-EN.book Page 58 Monday, August 31, 2009 2:32 PM Printing Functions Using the Auto Document Feeder when Combining Originals D Use the {U}{T} keys to select original and paper size, and then press the {OK} key. A Place the originals face up in the Auto Document Feeder. E Press the {Start} key. 3 AJK153S Note ❒ The first (top) original will be printed on the left side of the print. B Press the {Combine/Repeat} key.
C2758608_Platinum3-EN.book Page 59 Monday, August 31, 2009 2:32 PM Printing Functions C Use the {U}{T}keys to select Re- Repeat Use this function to repeat the image twice on the same sheet of paper. peat 2, and then press the {OK} key. D Use the {U}{T} keys to select original and paper size, and then press the {OK} key. Limitation ❒ You cannot use the optional Auto Document Feeder with the Repeat function. 3 E Press the {Start} key.
C2758608_Platinum3-EN.book Page 60 Monday, August 31, 2009 2:32 PM Printing Functions C Press the {Start} key. Skip Feed/A3 Paper Feed Skip Feed If the backs of prints are dirty, you can use the Skip Feed function to make the drum rotate twice instead of once with every sheet of paper fed. This gives you time to remove prints one by one from the paper delivery tray, or to insert a sheet of paper between two prints.
C2758608_Platinum3-EN.book Page 61 Monday, August 31, 2009 2:32 PM Printing Functions ❒ When the Hold Data-in mode is off, the A3 Paper Feed function cannot be used. When using the A3 Paper Feed function for online printing, set Hold Data-in mode to on after Master Making, and then specify A3 Paper Feed to print. A Press the {Skip Feed/A3 Paper Feed} key. Security Mode Use this function to prevent others from accessing your masters and making prints of confidential documents after you have done so.
C2758608_Platinum3-EN.book Page 62 Monday, August 31, 2009 2:32 PM Printing Functions Online Printing Online printing allows you to use this machine as a PC printer. Limitation ❒ The optional printer controller is required. Reference For details about online printing, refer to the manual for the printer controller. 3 Hold Data-in You can select whether or not the machine automatically switches to Online mode when it receives data from a PC. Press the {Hold Data-in} key to switch it on or off.
C2758608_Platinum3-EN.book Page 63 Monday, August 31, 2009 2:32 PM Program Program Use this function to store up to nine frequently used print job settings and to recall them for future use. Note ❒ The stored contents will not be cleared even when you turn off the main switch. ❒ The stored contents cannot be deleted. To change the contents of a program, overwrite it with new print settings.
C2758608_Platinum3-EN.book Page 64 Monday, August 31, 2009 2:32 PM Printing Functions E Press the {Start} key. Recalling a Program A Press the {Program} key. 3 ANT128S ANT120S B Use the {U}{T} keys to select Recall, and then press the {OK} key. C Use the {U}{T} keys to select the number to recall, and then press the {OK} key. The stored settings are displayed. D Confirm that the settings are correct, and then set your original.
C2758608_Platinum3-EN.book Page 65 Monday, August 31, 2009 2:32 PM Make Color Prints Make Color Prints Color drum units (red, blue, green, brown, yellow, purple, navy, maroon, orange and teal) are available as options in addition to the standard black unit. For making color prints, a separate drum unit is necessary for each color. C Hold the rail on the drum and slide out the drum while pulling the release towards you.
C2758608_Platinum3-EN.book Page 66 Monday, August 31, 2009 2:32 PM Printing Functions E Insert the color drum unit along the guide rail. H Close the front cover. 3 ANT059S ANT053S F Slide in the drum unit until it locks into position. Note ❒ Make sure that the Cover Open indicator (M) turns off, and the Color indicator is lit. Making Color Prints A Make sure that the Color indicator is lit. ANT049S B Set your original. C Press the {Start} key. G Lower the drum unit lock lever.
C2758608_Platinum3-EN.book Page 67 Monday, August 31, 2009 2:32 PM Make Color Prints C Press the {Start} key. Printing in Two Colors After printing in one color, you can print in another color on the same side of the print. Important ❒ Leave the prints for a while before printing on them again to let the ink dry. ❒ If the prints are not dry, the paper feed roller might become dirty. In this case, wipe off the roller with a cloth. Note ❒ You cannot print in two colors at a time.
C2758608_Platinum3-EN.book Page 68 Monday, August 31, 2009 2:32 PM Printing Functions Combination Chart This combination chart shows which modes can be used together. Blank means that these modes can be used together. × means that these modes cannot be used together.
C2758608_Platinum3-EN.book Page 69 Monday, August 31, 2009 2:32 PM 4. Troubleshooting If Your Machine Does Not Operate as You Want The following chart gives explanations of common problems and messages. If other messages appear, follow the instructions displayed. If a malfunction or a misfeed occurs, the following messages will appear on the display. ❖ When a Message is Displayed Message Causes Solutions Set the original.
C2758608_Platinum3-EN.book Page 70 Monday, August 31, 2009 2:32 PM Troubleshooting Printing Problems Problem Cause See p.68 “Combination Chart”. Parts of the image are not printed in Edge Erase mode. Adjust the edge erase margin with the user tools. See “Erase Border Width” on p.108 “4 Initial Settings”. The edge erase margin that you set is too wide. The original has very narrow margins. 4 Action When you try to select several Some functions cannot be functions at the same time, used together.
C2758608_Platinum3-EN.book Page 71 Monday, August 31, 2009 2:32 PM Loading Paper into the Paper Feed Tray Loading Paper into the Paper Feed Tray The Load Paper indicator (B) lights when the paper feed tray runs out of paper. Replenishing Paper A Press the {Clear/Stop} key. Note ❒ The paper feed tray will lower without the key being pressed when the printing paper runs out. ❒ The top sheet might remain between the feed rollers. In this case, remove the top sheet.
C2758608_Platinum3-EN.book Page 72 Monday, August 31, 2009 2:32 PM Troubleshooting C Load Changing the Paper Size paper into the paper feed tray. A Remove the paper from the paper feed tray. ANT074S 4 ANT073S The paper feed tray will lower. B Shift the paper feed side plates lock lever forward. Adjust the paper feed side plates to match the paper size. 1 Note ❒ Correct any paper curl before setting the paper. ❒ Make sure that the side plates touch the paper lightly.
C2758608_Platinum3-EN.book Page 73 Monday, August 31, 2009 2:32 PM When the Add Ink Indicator (j) Lights When the Add Ink Indicator (j) Lights The Add Ink indicator (j) lights when it is time to supply ink. R CAUTION: • Keep the ink or ink container out of reach of children. R CAUTION: • Be careful not to get ink on your clothes when replacing an ink container. Ink stains on clothes are hard to remove. R CAUTION: • When disposing of a used ink container, reattach the cap to prevent ink from splattering.
C2758608_Platinum3-EN.book Page 74 Monday, August 31, 2009 2:32 PM Troubleshooting A Open the front cover. ANT057S B Push the ink holder lever. 4 ANT060S C Pull out the ink holder.
C2758608_Platinum3-EN.book Page 75 Monday, August 31, 2009 2:32 PM When the Add Ink Indicator (j) Lights D Remove the used ink cartridge. ANT091S E Remove the cap of the new ink cartridge. 4 ANT098S F Insert the new cartridge into the ink holder.
C2758608_Platinum3-EN.book Page 76 Monday, August 31, 2009 2:32 PM Troubleshooting Note ❒ Always supply ink of the same color. ❒ Be sure to firmly insert the part indicated by the arrow mark into the guide. ANT097S 4 G Return the ink holder to its original position until it clicks. ANT090S H Close the front cover. ANT059S The machine will start idling to supply ink to the drum. Note ❒ It will stop when the correct amount of ink reaches the drum.
C2758608_Platinum3-EN.book Page 77 Monday, August 31, 2009 2:32 PM Master Roll Replacement Master Roll Replacement The Master End indicator (C) is lit when it is time to replace the master roll. A Pull out the master tray. D Remove the used master roll and pull out both spools. Then, insert both spools into a new master roll. 4 TSLT010E ANT065S B Press the release button to open the master feeding cover. Note ❒ It is necessary to replace the master roll even if some master remains on the old roll.
C2758608_Platinum3-EN.book Page 78 Monday, August 31, 2009 2:32 PM Troubleshooting F Insert the master and set its leading edge to the position of the marks. ANT080S 4 G Close the master feeding cover firmly. ZFRH250E H Close the master tray.
C2758608_Platinum3-EN.book Page 79 Monday, August 31, 2009 2:32 PM Placing a New Roll of Tape in the Tape Dispenser (Optional) Placing a New Roll of Tape in the Tape Dispenser (Optional) Note ❒ Make sure that the main switch is turned on and the power switch of the tape dispenser is off. C Feed the leading edge of the roll in the dispensing slot until it stops. A Open the cover of the tape dispenser. 4 TSLP012E Note ❒ Push the tape as far as possible through the slot.
C2758608_Platinum3-EN.book Page 80 Monday, August 31, 2009 2:32 PM Troubleshooting x Clearing Misfeeds The location indicators show where the jam has occurred. Important ❒ When clearing misfeeds, do not turn off the main switch. Otherwise, your print settings are cleared. “x + P” Original Misfeeds Occur in the Auto Document Feeder An original misfeed has occurred in the optional Auto Document Feeder.
C2758608_Platinum3-EN.book Page 81 Monday, August 31, 2009 2:32 PM x Clearing Misfeeds D Pull the green knob towards you to remove the original. TPEH220E E Return the document feed sheet to its original position. F Close the Auto Document Feeder cover until it clicks into position.
C2758608_Platinum3-EN.book Page 82 Monday, August 31, 2009 2:32 PM Troubleshooting -To prevent original misfeeds Use the exposure glass for the following kinds of originals: • Originals heavier than 128g/m2, 34 lb. • Originals lighter than 52g/m2, 14 lb. • Originals smaller than 148mm × 210mm, 5.9" × 8.3" • Originals larger than 297mm × 864mm, 11.6" × 34.
C2758608_Platinum3-EN.book Page 83 Monday, August 31, 2009 2:32 PM x Clearing Misfeeds “x + A” Paper Misfeeds in the Paper Feed Section A paper misfeed has occurred in the paper feed section. R CAUTION: • Be careful not to cut yourself on any sharp edges when you reach inside the machine to remove misfed sheets of paper or masters. A Slowly but firmly pull out the paper. 4 ZFRY010E B If the indicators remain lit, open the front cover and close it firmly or press {OK} key. Reference See p.
C2758608_Platinum3-EN.book Page 84 Monday, August 31, 2009 2:32 PM Troubleshooting B Remove the misfed paper. TSLH02BE C Insert the drum unit until it locks into position, and then lower the drum unit lock lever. 4 ANT061S D Close the front cover. ANT059S Reference See p.86 “To prevent paper misfeeds”.
C2758608_Platinum3-EN.book Page 85 Monday, August 31, 2009 2:32 PM x Clearing Misfeeds “x + C” Paper Misfeeds in the Paper Exit Section A paper misfeed has occurred in the paper exit section. R CAUTION: • Be careful not to cut yourself on any sharp edges when you reach inside the machine to remove misfed sheets of paper or masters. A Remove the misfed paper. 4 ANT094S Note ❒ Make sure that the paper delivery end plate and side plates are in their correct positions.
C2758608_Platinum3-EN.book Page 86 Monday, August 31, 2009 2:32 PM Troubleshooting C Remove the misfed paper. ANT084S D Close the master eject unit. 4 ANT083S E If the indicators remain lit, open the front cover and close it firmly or press {OK} key. -To prevent paper misfeeds If paper is curled or the margin on the leading edge of the original is too narrow, the following action is necessary. • Before using the paper, correct the curl as shown below.
C2758608_Platinum3-EN.book Page 87 Monday, August 31, 2009 2:32 PM x Clearing Misfeeds • If you are unable to correct the paper curl, place the paper in the paper feed tray with it curling either upward or downward, as shown in the illustration below. 4 TPEY990E • When the leading edge margin of the original is less than 5mm, 0.2" , or when there is a solid image on the leading edge, feed the original from the edge with the widest margin.
C2758608_Platinum3-EN.book Page 88 Monday, August 31, 2009 2:32 PM Troubleshooting “x + D” Master Misfeeds in the Master Feed Section A master misfeed has occurred in the master feed section. A Pull out the master tray. 4 ANT065S B Open the master feeding cover, and then remove the misfed master inside. ZJVH070E C Set the leading edge of the master to the position of the marks.
C2758608_Platinum3-EN.book Page 89 Monday, August 31, 2009 2:32 PM x Clearing Misfeeds D Close the master feeding cover firmly. ZFRH250E E Close the master tray. 4 ANT066S “x + A + B” Paper Misfeeds in the Paper Feed Section The paper is jammed between the drum and the paper feed section. A Unlock the lever and then pull out the drum unit.
C2758608_Platinum3-EN.book Page 90 Monday, August 31, 2009 2:32 PM Troubleshooting B Remove the misfed paper from inside. TSLH01BE C Insert the drum until it locks into position, and then lower the lock lever. 4 ANT061S D Close the front cover.
C2758608_Platinum3-EN.book Page 91 Monday, August 31, 2009 2:32 PM x Clearing Misfeeds “x + B + E” Master Misfeeds in the Master Eject Section Either a master misfeed has occurred in the master eject section, or the master is wrapped around the drum unit. A Grip the handle and pull out the master eject box. 4 ANT095S B Remove the misfed master. ZFRH120E Note ❒ Be careful not to stain your hands with ink when you touch used masters. C Return the master eject box to its original position.
C2758608_Platinum3-EN.book Page 92 Monday, August 31, 2009 2:32 PM Troubleshooting When the master is wrapped around the drum A Unlock the lever and then pull out the drum unit. ANT054S 4 B Unlock the lever to open the clamp of drum unit. ANT111S C Remove the misfed master.
C2758608_Platinum3-EN.book Page 93 Monday, August 31, 2009 2:32 PM x Clearing Misfeeds Note ❒ When the lever is released, the clamp will be set back. Make sure that the clamp is set correctly as shown. ANT087S 4 D Insert the drum until it locks into position, and then lower the lock lever. ANT061S E Close the front cover.
C2758608_Platinum3-EN.book Page 94 Monday, August 31, 2009 2:32 PM Troubleshooting When the Open Cover/Unit Indicator (M) Lights and a Message is Displayed A message is displayed explaining the place where the doors/covers are not properly closed. Master Eject Unit is Open A Close the master eject unit. Front Cover is Open A Close the front cover completely. 4 ANT083S ANT059S Cover of Optional Auto Document Feeder is Open A Close the Auto Document Feeder until it clicks into place.
C2758608_Platinum3-EN.book Page 95 Monday, August 31, 2009 2:32 PM When the Master End Indicator (C) Lights and a Message is Displayed When the Master End Indicator (C) Lights and a Message is Displayed A message is displayed explaining the place in the master feed section that is not properly set. Master Feeding Cover is Open A Close the master feeding cover firmly with both hands. 4 ZFRH250E Master Tray is Not Set Properly A Push in the master tray completely.
C2758608_Platinum3-EN.book Page 96 Monday, August 31, 2009 2:32 PM Troubleshooting When the Master Eject Indicator (k) Lights The master eject indicator (k) lights when it is time to empty master eject box. A Grip the handle and pull out the master eject box. 4 ANT095S B Remove the used masters. ANT088S Note ❒ Spread out an old newspaper, and then tip the used masters onto the newspaper. Throw away the used masters. C Return the master eject box to its original position.
C2758608_Platinum3-EN.book Page 97 Monday, August 31, 2009 2:32 PM When Other Indicators Light When Other Indicators Light u Set Key Counter. The key counter (option) is not set. Insert the key counter into its slot.
C2758608_Platinum3-EN.book Page 98 Monday, August 31, 2009 2:32 PM Troubleshooting Poor Printing Dirt on the Back Side of Paper GRDIRT0E 4 Note ❒ When you use paper that is smaller than the original, select the proper reduction ratio. Otherwise, you might get dirty background prints. ❒ When you use postcards, the background might be dirty because postcards do not absorb ink well. A Turn off the main switch. ANT076S B Open the front cover.
C2758608_Platinum3-EN.book Page 99 Monday, August 31, 2009 2:32 PM Poor Printing C Unlock the lever, and then pull out the drum unit. ANT054S Reference For details about how to remove the drum unit, see p.65 “Changing the Color Drum Unit”. 4 D Clean the pressure roller with a clean cloth. ANT058S E Insert the drum unit until it locks into position, and then lower the drum unit lock lever.
C2758608_Platinum3-EN.book Page 100 Monday, August 31, 2009 2:32 PM Troubleshooting F Close the front cover. ANT059S G Turn on the main switch. 4 ANT077S Dirt on the Front Side of Paper (Black Line/Stain) GRBLAC1E Note ❒ If there is no margin or if there is a solid image area near the leading edge of the original, make a margin of at least 5mm, 0.2" at the leading edge. Otherwise, the paper exit pawl might become dirty and cause black lines on prints.
C2758608_Platinum3-EN.book Page 101 Monday, August 31, 2009 2:32 PM Poor Printing Blank Prints or Incomplete Prints GRWHIT0E • Make sure that the paper feed side plates touch the paper lightly. Shift the lock lever backward. 4 TSLY015E • When you use the optional Auto Document Feeder, make sure that the original guides contact the originals lightly. When blank or incomplete prints persist even after you have checked the above, perform the following procedure. A Open the front cover.
C2758608_Platinum3-EN.book Page 102 Monday, August 31, 2009 2:32 PM Troubleshooting B Unlock the lever and pull out the drum unit. ANT054S Reference For details about how to remove the drum unit, see p.120 “Maintaining the Machine”. 4 C Remove paper that is stuck to the drum. TSLH02BE D Insert the drum unit until it locks into position, then lower the drum unit lock lever.
C2758608_Platinum3-EN.book Page 103 Monday, August 31, 2009 2:32 PM Poor Printing E Close the front cover.
C2758608_Platinum3-EN.
C2758608_Platinum3-EN.book Page 105 Monday, August 31, 2009 2:32 PM 5. User Tools Accessing the User Tools This section is intended for the machine administrator. The user tools allow the administrator to customize the default settings of this machine. Reference For the detailed user tool menu, see p.106 “User Tools Menu”. Quitting User Tools A To quit the User Tools menu, press the {User Tools} key. A Press the {User Tools} key. BFU014S BFU014S B Use the {U}{T} keys to select the desired user tool.
C2758608_Platinum3-EN.book Page 106 Monday, August 31, 2009 2:32 PM User Tools User Tools Menu 1 Counter No. Mode Description 1 Display Counter Shows the total number of masters and prints. Note ❒ The trial print will not be counted as part of the total. 2 System 5 No. Mode Description 1 Auto Reset Timer The machine automatically returns to its initial condition if it has not been operated for a certain period of time. Note ❒ Default: Off 2 Disp.
C2758608_Platinum3-EN.book Page 107 Monday, August 31, 2009 2:32 PM User Tools Menu No. Mode Description 8 Energy Saver Timer You can specify the time taken for the machine to enter Energy Saver mode. Note ❒ Default: 3 min. (minutes) 9 Auto Off Timer You can select to use the auto off timer. Note ❒ Default: Off 10 Data Print You can print the log data and the counter list. 3 Set Operation Mode No.
C2758608_Platinum3-EN.book Page 108 Monday, August 31, 2009 2:32 PM User Tools 4 Initial Settings No. Mode Description 1 Master Making Density You can specify the image density that is selected by default when the power is turned on. Note ❒ Default: Normal 2 Original Type You can specify the original type that is selected by default when the power is turned on. Note ❒ Default: Text 3 Ratio You can specify the reproduction ratio that is selected by default when the power is turned on.
C2758608_Platinum3-EN.book Page 109 Monday, August 31, 2009 2:32 PM User Tools Menu 5 Mode Settings No. Mode Description 1 Auto Cycle You can select to have Auto Cycle mode as either “On” or “Off” when the power is turned on. Note ❒ Default: On 2 Background Correction When you make prints in Photo, or Text/Photo mode, the background of the prints might appear dirty. In this case, you can select background correction to improve the clarity of your prints.
C2758608_Platinum3-EN.book Page 110 Monday, August 31, 2009 2:32 PM User Tools 6 Administrator Tools ❖ User Codes If user codes are turned on, operators must enter their user codes before they can operate the machine. The machine keeps count of the number of masters and prints made under each user code. See “3 User Code Management” below. 1 Display Counter(s) You can check the number of masters and copies made under each user code.
C2758608_Platinum3-EN.book Page 111 Monday, August 31, 2009 2:32 PM User Tools Menu 7 Online Settings Limitation ❒ The optional printer controller is required for these settings. ❒ The displayed Online Settings menus depend on the type of printer controller. No. Mode Description 1 Hold Data-in You can select to have Hold Data-in mode either “On” or “Off” when the power is turned on, or after mode settings have been cleared.
C2758608_Platinum3-EN.book Page 112 Monday, August 31, 2009 2:32 PM User Tools 8 I/O Timeout Allows you to specify how many seconds the machine waits before it cancels a stalled print job. Note that if job data from other ports often arrives while earlier print jobs are in progress, specifying a longer timeout period will prevent the machine canceling the earlier jobs. Note ❒ Default: 15Sec. 9 I/O Buffer Allows you to specify the size of the I/O Buffer.
C2758608_Platinum3-EN.book Page 113 Monday, August 31, 2009 2:32 PM User Code User Code In User Code mode, users need to enter a user code before they can use the machine. The machine keeps count of the numbers of masters and prints under each user code. Note ❒ To use this feature, User Code mode must be set to “Use”. See “3 User Code Management” on p.110 “6 Administrator Tools”.
C2758608_Platinum3-EN.book Page 114 Monday, August 31, 2009 2:32 PM User Tools To clear the counter for each user code Clearing the Counter You can clear each or all of the user code counters. A Press the {User Tools} key. A Use the {U}{T} keys to select Clear per User. B Use the {U}{T} keys to select the user code that you wish to clear. BFU014S B Use the {U}{T} keys to select 6 5 Administrator Tools, and then press the {OK} key. C Press the {OK} key.
C2758608_Platinum3-EN.book Page 115 Monday, August 31, 2009 2:32 PM 6. Remarks Operation Notes General Cautions • • • • • • • • • • • • • • • • • • • • • While printing, do not turn off the main switch. While printing, do not open the door or covers. While printing, do not unplug the power cord. While printing, do not move the machine. Keep corrosive liquids, such as acid, off the machine. Open and close the door and covers softly. Do not put anything except originals on the machine.
C2758608_Platinum3-EN.book Page 116 Monday, August 31, 2009 2:32 PM Remarks • When making duplex prints, misdetection of paper wrapping might occur if the paper delivery sensor detects a black area at the leading edge of the back side. Keep at least 5 mm, 0.2" margin at the leading edge of the back side of the printing paper. • Press the {Proof} key to perform a test print as the first few prints might be light.
C2758608_Platinum3-EN.book Page 117 Monday, August 31, 2009 2:32 PM Operation Notes • In Text/Photo mode, moire patterns might occur when screened originals are printed. In this case, make prints in Text or Photo mode. • When you use originals with light lettering, edges of the letters might be printed clearly and the inside of the letters might be light. In this case, increase the image density. • When marks on the printing paper occur, clean the paper feed roller. See p.120 “Maintaining the Machine”.
C2758608_Platinum3-EN.book Page 118 Monday, August 31, 2009 2:32 PM Remarks Where to Put Your Machine Your machine's location should be carefully chosen because environmental conditions greatly affect its performance. Environmental Conditions Optimum environmental conditions R CAUTION: • Keep the machine away from humidity and dust. Otherwise a fire or an electric shock might occur. • Do not place the machine on an unstable or tilted surface. If it topples over, an injury might occur.
C2758608_Platinum3-EN.book Page 119 Monday, August 31, 2009 2:32 PM Where to Put Your Machine Power Connection R WARNING: • Connect the power cord directly into a wall outlet and never use an extension cord. • Only connect the machine to the power source describe in the manual. • Do not damage, break or make any modifications to the power cord. Do not place heavy objects on it. Do not pull it hard nor bend it more than necessary. These actions could cause an electric shock or fire.
C2758608_Platinum3-EN.book Page 120 Monday, August 31, 2009 2:32 PM Remarks Maintaining the Machine To maintain high print quality, clean the following parts and units regularly. Exposure Glass Cover Main Frame A Lift the exposure glass cover. B Clean the exposure glass cover with a damp cloth and wipe it with a dry cloth. Exposure Glass A Lift the exposure glass cover or optional Auto Document Feeder. B Clean A and B. Note ❒ When using the exposure glass, clean B only.
C2758608_Platinum3-EN.book Page 121 Monday, August 31, 2009 2:32 PM Maintaining the Machine Optional Document Feeder Cleaning the Sheet A Lift the document feeder. B Clean the sheet with a damp cloth and wipe it with a dry cloth. ANT056S 6 Note ❒ If you do not clean the sheet, marks on the sheet will be printed.
C2758608_Platinum3-EN.
C2758608_Platinum3-EN.book Page 123 Monday, August 31, 2009 2:32 PM 7. Specifications Main Frame ❖ Configuration: Desktop ❖ Printing Process: Full automatic one drum system ❖ Original Type: Sheet/Book ❖ Original Size: Maximum 297 mm × 432 mm, 11.7" × 17.
C2758608_Platinum3-EN.book Page 124 Monday, August 31, 2009 2:32 PM Specifications ❖ Leading Edge Margin: 5 mm ± 3 mm, 0.2" ± 0.12" ❖ Print Paper Weight: 47.1 g/m2 to 209.3 g/m2, 12.5 lb. to 55.6 lb. • When the A3 Paper Feed function is used 52.3 g/m2 to 157 g/m2, 14 lb. to 42 lb. ❖ Print Speed: 3 steps • Setting 1: 80 sheets/minute • Setting 2: 100 sheets/minute • Setting 3: 130 sheets/minute Setting 1 fixed (When the A3 Paper Feed function is used) ❖ First Copy Time (Master Process Time): 32.
C2758608_Platinum3-EN.book Page 125 Monday, August 31, 2009 2:32 PM Main Frame ❖ Dimensions (W × D × H): Width Depth Height Stored 750 mm, 29.5" 681 mm, 26.8" 633 mm, 24.9" Stored with Auto Document Feeder 750 mm, 29.5" 681 mm, 26.8" 686 mm, 27.0" Set up 1,244 mm, 49.0" 681 mm, 26.8" 633 mm, 24.9" Set up with Auto Document Feeder 1,244 mm, 49.0" 681 mm, 26.8" 686 mm, 27.0" ❖ Weight: • Main Frame with Exposure Glass Cover: 70 kg, 154.3 lb.
C2758608_Platinum3-EN.
C2758608_Platinum3-EN.book Page 127 Monday, August 31, 2009 2:32 PM Auto Document Feeder (ADF) Auto Document Feeder (ADF) ❖ Mode: • ADF mode ❖ Original size: • A3L – A5KL • 11" × 17"L – 51/2" × 81/2"KL ❖ Original weight: • One-sided originals: 52 – 105 g/m2 (14 – 28 lb.) ❖ Number of originals to be set: • 30 sheets (80 g/m2, 20 lb.) ❖ Maximum power consumption: • Less than 25 W (power is supplied from the main unit.) ❖ Dimensions (W × D × H): • 550 × 470 × 90 mm, 21.7" × 18.6" × 3.
C2758608_Platinum3-EN.book Page 128 Monday, August 31, 2009 2:32 PM Specifications Consumables Name Size Remarks Master for LG drum Length: 125 m, 410ft/roll 260 masters can be made per roll Width: 240 mm, 9.
C2758608_Platinum3-EN.
C2758608_Platinum3-EN.
C2758608_Platinum3-EN.
C2758608_Platinum3-EN.
Paper type: OK Prince Eco G100(55kg), Paper Thickness=80 µm // Pages in book=136 // Print scale=81% Gap (when printed at 81% scale) = Pages in book × Paper thickness / 2 = 5.440000 mm Introduction This manual contains detailed instructions and notes on the operation and use of this machine. For your safety and benefit, read this manual carefully before using the machine. Keep this manual in a handy place for quick reference. Important Contents of this manual are subject to change without prior notice.
Paper type: OK Prince Eco G100(55kg), Paper Thickness=80 µm // Pages in book=136 // Print scale=81% Gap (when printed at 81% scale) = Pages in book × Paper thickness / 2 = 5.
Quick Install Guide English 1. Installing the VC-20 software Important: Do not plug the USB cable into the computer before the VC-20 software has been installed. In order to run this install procedure, ensure the computer has been logged on with administrative rights. 1.1. Insert the CD ROM into the computer. 1.2. Select [Quick Install] to install the VC-20 software. 1.3. After installing the software, the [Add Printer Wizard] automatically starts.
Español Lea esto atentamente antes de utilizar este producto. Para un uso correcto y seguro, asegúrese de leer la Información de seguridad del “Manual de instrucciones” antes de utilizar este producto. 1. Instalación del software VC-20 Importante: No conecte el cable USB al ordenador antes de instalar el software VC-20. Para ejecutar este procedimiento de instalación, asegúrese de haber abierto sesión en el ordenador con derechos de administrador. 1.1. Inserte el CD-ROM en el ordenador. 1.2.
Operating Instructions Version 1.
ZipRIP hardware and software is the property of SMA Australia (Pty) Ltd. RICOH Software is the property of RICOH Company Ltd. This documentation or any part of it may not be reproduced, stored or transmitted in any form, including but not limited to electronic, photocopying, mechanical copying, electrostatic copying, recording or other means without express written permission of SMA Australia (Pty) Ltd or RICOH Company Ltd.
Introduction This manual contains detailed instructions and notes on the operation and use of the VC-20. For your safety and benefit, read this manual carefully before using the VC-20. Keep this manual in a handy place for quick reference. Important Contents of this manual are subject to change without prior notice. In no event will the company be liable for direct, indirect, special, incidental, or consequential damages as a result of handling or operating the machine.
Manuals for this product The manual provided is specific to the VC-20. The manual is in PDF format. Adobe Acrobat Reader/Adobe reader is necessary to view the manuals. Product description The VC-20 is a USB 1.1 or USB 2 (full speed) interface for Digital Duplicators. The VC-20 can print directly from a PC to the Digital Duplicator. This will significantly improve the quality of printed material as well as speed up the printing jobs.
Contents Introduction ............................................................................... 3 Manuals for this product ......................................................... 4 Product description .................................................................. 4 1. Getting Started .................................................................. 6 Basic Specifications ................................................................... 6 Digital Duplicator Driver Groups .....................
1. Getting Started Basic Specifications Printer Language: ................................Windows GDI Supported Resolutions: .......................300 and 400 dpi Graphics Screening: ............................Coarse, Fine, Line Art, Error Diffusion Density control supported Supported Drivers:..............................Windows 98 2nd Edition, Windows ME, Windows 2000, Windows XP and Windows 2003 Server (Standard) Ports:.................................................. USB 1.1 or USB 2.
Digital Duplicator Driver Groups Driver Name Digital Duplicator Model VC-20 B4 300 GDI DX 3440 / JP755 / CP6123b+ / JP785C / CP6200C VC-20 LG 300 GDI DX 3340 / CP6143L / LDD120 / 3180DNP / SD360 / JP735 / CP6123L+ LDD735 / CP6123a+ VC-20 A4 300 GDI DX3240 VC-20 A3 400 GDI DX 4542 / CP6244+ / LDD245 / 3270DNP / SD430 VC-20 B4 400 GDI VC-20 OM Mar 2006 7
Package Contents VC-20 Check the following components are packed with the VC-20. VC-20 Installation Sheet Installation CD Safety Sheet Screws (x3) Important Note: The VC-20 is not supplied with a USB cable. This cable must be obtained separately.
2. Installing the VC-20 This section gives instructions for configuring the printer, and installing software and connecting the printer and computer. Requirements Before using this printer, make sure all environmental and electrical requirements are met. Before beginning the installation, ensure the following: ✤ Ensure all of the items needed to complete a successful installation are available. ✤ Read the documentation to become familiar with the installation procedures.
The VC-20 Software Components The VC-20 software contains the following components: VC-20PrinterServer VC-20PrinterServer is the main software engine for the VC-20. It runs as a service application on the Windows operating system after installation. Printer Driver The GDI Printer Driver generates the print data. USB Driver The USB Driver enables the necessary support within the Windows operating system for the VC-20PrinterServer to communicate with the VC-20 hardware.
Installing the VC-20 Printer Driver and Utilities Important: Do not plug the USB cable into the computer before the VC-20 software has been installed. In order to run this install procedure, ensure the computer has been logged on with administrative rights. Before beginning the driver installation, ensure the Windows Operating System CD is available. Before running this install CD, ensure all programs are closed and files saved. The software is located on the VC-20 Printer Drivers & Utilities CD ROM.
3. Select from the following options. Quick Install - Installs the VC-20PrinterServer, VC-20 GUIClient, Printer Driver and USB Driver. VC-20 GUIClient - Installs the Setting & Monitoring Utility software. Select Language - Optional language selection. Browse the CD ROM - Browsing of all the files and folders on the CD ROM. Exit - Exits the installation wizard. Readme - Additional information not available at the time the manual was written.
Selecting Quick Install Selecting the Quick Install button will automatically begin the installation procedure to install the VC-20PrinterServer, VC-20 GUIClient, Printer Driver and USB Driver. Follow the procedures below for the operating system, the VC-20 will be installed onto. Note: The installation procedure is the same for all supported operating systems. There may be minor differences in display of [Add Printer Wizard] as well, some order depending on the difference of operating system used.
3. Click [OK] to begin the installation procedure. 4. The installation will commence. 5. Windows 2000 and XP only. On completion of the initial installation procedure, the [Windows Add Printer Wizard] will automatically open. Click [Next].
6. Select [Local printer]. For Windows 2000 and XP, ensure [Automatically detect and install my Plug and Play printer] is not selected. Click [Next]. 7. For Windows 2000 and XP, in the [Select the Printer Port] dialogue box, select the VC-20 port. Click [Next]. For Windows 98SE and ME go to step 8 first and then step 7.
Note: Windows 98SE and Windows ME do not automatically direct the installation to the printer driver files that are installed onto the computer. Click [Have Disk] and direct the installation to c:\Program Files\VC-20\Printer. Ensure the oemsetup.inf file is selected. Click [OK]. 8. Select the VC-20 driver that matches the appropriate Digital Duplicator. Refer to the Digital Duplicator Driver Groups table in the front of this manual.
9. Change the [Printer name] if required. Click [Next]. 10. Select if the printer will be shared on a network or not. Click [Next].
11. Select [No] or [Yes] to print a test page and click [Next]. 12. For Windows 2000 and XP only. At the [Completing the Add Printer Wizard], click [Finish].
13. The printer driver will be installed. For Windows 2000 and XP, Windows displays a warning message relating to the certification of the driver, select the option to continue with the installation. For Windows 98SE and ME. The computer will automatically reboot. 14. For Windows 2000 and XP only. When the installation procedure is complete, click [Close] in the VC-20 Setup utility.
3. Installing the VC-20 Hardware This section describes connecting the hardware of the VC-20 and the computer. Connecting the VC-20 Important: This procedure must only be done after the software has been installed. 1. Connect the USB cable to the VC-20 port on the chassis of the Digital Duplicator. 2. Connect the opposite end of the USB cable to an available USB port on the computer. 3. The computer will automatically detect that new hardware has been found. 4.
6. The computer will open the [Files Needed] window. Select [OK]. 7. At the prompt, direct the installation procedure to c:\Program Files\VC-20\USB to locate the [libusb0.sys]. 8. For Windows 2000 and XP the [System Settings Change] window will open and will ask to restart the computer. Click [Yes]. For Windows 98SE/ME a message “Computer need to reboot” will appear. Click [OK] and the computer will automatically reboot. The VC-20 is ready to be used.
4. Basic Operation of the VC-20 After completing all the installation procedures and installation of the relevant driver for the Digital Duplicator being connected to, the VC-20 is ready for use. Turning on VC-20 Connect the USB cable between the VC-20 and the computer. Turning off VC-20 Disconnect the USB cable between the VC-20 and the computer. Printer Driver Properties The VC-20 Printer Driver properties contains functions that are specific to the digital duplicator.
3. In the [Properties] dialogue box select [Printing Preferences]. In the case of Windows 98SE and ME, select the [Device Options] tab. 4. Select [Advanced] from the [Layout] tab of the [Printing Preferences] dialogue box. The digital duplicator functions are displayed. These functions can be set when a job is printed and will revert back to default on completion of the print.
Function Paper/Output Document Options Options Further Options Description Paper Size All supported paper sizes listed Select paper size Copy Count 1-9999 Select number of prints Advanced Printing Features Enable Activate the advanced printing features Deactivate the advanced printing features Disable Halftoning Auto Select Super Cell Dither 6 x 6 Dither 8 x 8 Windows selects an option Added gray levels Each spot = max 6x6 dots Each spot = max 8x8 dots Printer Features Eco.
Function Document Options Options Printer Features Further Options Description Rotate Image Default 1800 Image rotation Set Off as default.
Setting and Monitoring Utility The VC-20 comes with a setting and monitoring utility called [VC-20 GUIClient]. This application is automatically installed during the software and printer driver installation described in section 2 of this manual. The Setting and Monitoring Utility has the following functions: 1. Monitor the condition of the VC-20 and the Digital Duplicator. 2. Cancel print jobs. 3. Set logging levels and define paper size mismatch prompt behavior. 4. Displays version information. 5.
VC-20 GUIClient Functions VC-20 OM Mar 2006 27
Item Description Function [1] Drop down menu Access to version information and VC-20 settings. [2] About VC-20 Displays the VC-20 GUIClient version, VC-20PrinterServer version and the VC-20 PCB Firmware version.
Item Description Function [3] Settings Displays the different settings that can be applied to the VC-20. Logging Default is not selected. If selected logs VC-20 and duplicator status information. [Note] logs maximum detail. [Critical] logs minimum information. Note: Reboot the PC to effect this change.
Item Description Function Size Mismatch Prompts Enabled - If [VC-20 GUIClient] is running, [VC-20 GUIClient] will warn if a paper size mismatch has been detected and prompt to [Cancel] or [Retry] or [Ignore]. Disabled - [VC-20 GUIClient] will not warn if a paper size mismatch has occurred. Size Mismatch Prompts function only applies to duplicators that have paper size detection capability. Note: Reboot the PC to effect this change.
Item Description Function memory is not functioning. VC-20PrinterServer IP Address IP address of the computer the VC20 is installed on. Default 127.0.0.1 [VC-20 GUIClient] is installed on the same PC as VC-20. Note: Restart the [VC-20 GUIClient] for this setting to take effect. Port TCP/IP port used by [VC20PrinterServer ] to communicate with [VC-20 GUIClient]. Default 4660. Note: Reboot the PC for this setting to take effect. Spool Path Displays the spool path that print files are sent to.
Item Description Function [5] Displays VC-20 status. VC-20 Monitoring VC-20 connected. VC-20 not connected. [6] [7] Duplicator Resolution The [VC-20 GUIClient] detects and display the resolution of the duplicator the VC-20 is connected to. 300 300dpi duplicator detected. 400 400dpi duplicator detected. Drum Colo(u)r The [VC-20 GUIClient] displays black drum or colo(u)r drum loaded in the duplicator. Black type drum in the duplicator. Colo(u)r type drum in the duplicator.
Item Description Function [8] Select to cancel a print job. Job Cancel Button Cancel print job. Orange when job is being cancelled. [9] Job Tray Displays if a job is being processed by the VC-20. Job tray empty. Job being processed. PC sending page to VC-20 memory. [10] Duplicator Monitoring Monitors and displays the status of the duplicator. Duplicator not found. Duplicator ready.
Item Description Function Duplicator error Note: “Duplicator Error” symbol will also be shown if the Duplicator is in “Print Not Finished” condition. To clear this error the print job should be completed on the Duplicator. Duplicator busy.
Printing job with use of the VC-20 Before sending a print job, ensure the correct size paper is loaded in the machine. If the VC-20 does not find the size of paper that it is required to print on from the printer driver, it will indicate a paper mismatch error if [Size Mismatch Prompt] is enabled. To print to the VC-20, select the print option from the file menu of the application. In the print dialogue window, select the VC-20 driver installed and set the quantity of prints required.
5. Uninstalling the VC-20 This section describes uninstalling the VC-20 GUIClient software and the VC-20 printer driver. 1. Disconnect the USB cable from the computer. 2. Select [Printers] from [Settings] in the Start menu. 3. Select and right click on the VC-20 driver. Select [Delete]. 4. Click [Yes] to confirm the deletion. 5. Select [Control Panel] from [Settings] on the [Start] menu.
6. Select “Add or Remove Programs”. 7. Scroll and locate the VC-20 GUIClient application. 8. Select the program and click “Change/Remove”.
9. The VC-20 GUIClient uninstall port monitor will display during the uninstall procedure. A green tick will confirm completion.
6. Troubleshooting Check the steps below and refer to the table to solve problems with the VC20. 1. Check that the USB cable is securely connected to the Digital Duplicator and the computer. 2. Check the both computer and the Digital Duplicator are powered on. 3. Check that all operator recoverable errors are cleared on the Digital Duplicator. 4. Open the [VC-20 GUIClient] user interface and check that the Digital Duplicator and the VC-20 have been detected. 5.
Error The [VC-20 GUIClient] does not detect the VC20 The VC-20 is not located in the [Device Manager] on the computer. Cause Solution The VC-20 USB driver is Install the VC-20 not installed. software from the installation CD-ROM. The VC-20 is not connected to the computer. Connect the VC-20 to the computer with the USB cable. The [VC-20 GUIClient] is not set to the computer that the VC-20 is installed on.
Error Cause The Digital Duplicator is The [VC-20 GUIClient] does not detect the Digital switched off. Duplicator. There is a fault with the Digital Duplicator. Solution Switch the Digital Duplicator on. Restart the Digital Duplicator. Restart the computer the VC-20 is connected to. If the problem persists, contact the service technician. The VC-20 is not located in the [Device Manager] on the computer. The USB cable is not connected.
Error Cause Solution The VC20PrinterServer is not located in Windows Services The VC-20 software has not been installed correctly Install the VC-20 software from the installation CD ROM There is no VC-20 port available in the printer drivers port section The VC-20 software has not been installed correctly Install the VC-20 software from the installation CD ROM The image printed on The incorrect printer the Digital Duplicator driver is installed for is reduced or enlarged the Digital Duplicator in s
Copyright @ 2006 EN GB C646-8760
