Operating instructions
Table Of Contents
- General Settings Guide
- Introduction
- Important
- Notes:
- Manuals for This Machine
- TABLE OF CONTENTS
- How to Read This Manual
- Display Panel
- Accessing User Tools
- 1. Connecting the Machine
- Connecting to the Interfaces
- Network Settings
- Settings Required to Use the Printer/LAN-Fax
- Settings Required to Use Internet Fax
- Settings Required to Use E-mail Function
- Settings Required to Use Scan to Folder Function
- Settings Required to Use the Network Delivery Scanner
- Settings Required to Use Network TWAIN Scanner
- Settings Required to Use Document Server
- Using Utilities to Make Network Settings
- Connecting the Machine to a Telephone Line and Telephone
- 2. System Settings
- 3. Copier / Document Server Features
- 4. Facsimile Features
- General Features
- Scan Settings
- Send Settings
- Reception Settings
- Initial Settings
- Reception File Setting
- Program / Change / Delete Scan Size
- Registering Fax Information
- Forwarding
- Parameter Settings
- Special Senders to Treat Differently
- Authorized Reception
- Reception File Print Quantity
- Forwarding
- Print 2 Sided
- Memory Lock
- Paper Tray
- Programming/Changing Special Senders
- Authorized RX (Authorized Reception)
- Reception File Print Qty
- Forwarding
- Print 2 Sided
- Memory Lock
- Paper Tray per Sender
- Programming Initial Set Up of a Special Sender
- Deleting a Special Sender
- Box Settings
- 5. Printer Features
- 6. Scanner Features
- 7. Registering Addresses and Users for Facsimile/Scanner Functions
- Address Book
- Registering Names
- Authentication Information
- Fax Destination
- Fax Destination
- IP-Fax Destination
- Registering an IP-Fax Destination
- Changing a Registered IP-Fax Destination
- Using the IP–Fax Destination as the sender
- To change the IP-Fax Destination
- To select the protocol
- To program the SUB Code
- To program the SEP Code
- To set the International TX Mode
- To select the fax header
- Deleting a Registered IP-Fax Destination
- E-mail Destination
- Registering Folders
- Registering Names to a Group
- Registering a Protection Code
- Registering SMTP and LDAP Authentication
- 8. Other User Tools
- 9. Appendix
- INDEX
Connecting the Machine
34
1
Note
❒ For the Effective Protocol setting, check that the protocol you want to use is
set to [Active].
❒ [LAN Type] is displayed when the wireless LAN interface board is installed.
When both Ethernet and wireless LAN (IEEE 802.11b) are connected, the se-
lected interface takes precedence.
Reference
p.59 “Interface Settings”
IEEE 1394 (IPv4 over 1394)
This section lists the settings required for using Document Server function with
an IEEE 1394 connection.
For details about how to specify the settings, see "Interface Settings".
Note
❒ [IEEE 1394] is displayed when the IEEE 1394 interface board is installed.
❒ For the Effective Protocol setting, check that the protocol you want to use is
set to [Active].
Reference
p.59 “Interface Settings”
Interface Settings/Network Ethernet Speed As required
Interface Settings/Network LAN Type Necessary
Interface Settings/Network Permit SNMPv3 Communication As required
Interface Settings/Network Permit SSL/TLS Communication As required
Interface Settings/Network Host Name As required
Menu User Tool Setting Requirements
Interface Settings/IEEE 1394 IPv4 Address Necessary
Interface Settings/IEEE 1394 DDNS Configuration As required
Interface Settings/IEEE 1394 Host Name As required
Interface Settings/IEEE 1394 Domain Name As required
Interface Settings/IEEE 1394 WINS Configuration As required
Interface Settings/IEEE 1394 IPv4 over 1394 Necessary
Interface Settings/Network IPv4 Gateway Address As required
Interface Settings/Network DNS Configuration As required
Interface Settings/Network Effective Protocol Necessary
Menu User Tool Setting Requirements