Operating instructions
Table Of Contents
- General Settings Guide
- Introduction
- Important
- Notes:
- Manuals for This Machine
- TABLE OF CONTENTS
- How to Read This Manual
- Display Panel
- Accessing User Tools
- 1. Connecting the Machine
- Connecting to the Interfaces
- Network Settings
- Settings Required to Use the Printer/LAN-Fax
- Settings Required to Use Internet Fax
- Settings Required to Use E-mail Function
- Settings Required to Use Scan to Folder Function
- Settings Required to Use the Network Delivery Scanner
- Settings Required to Use Network TWAIN Scanner
- Settings Required to Use Document Server
- Using Utilities to Make Network Settings
- Connecting the Machine to a Telephone Line and Telephone
- 2. System Settings
- 3. Copier / Document Server Features
- 4. Facsimile Features
- General Features
- Scan Settings
- Send Settings
- Reception Settings
- Initial Settings
- Reception File Setting
- Program / Change / Delete Scan Size
- Registering Fax Information
- Forwarding
- Parameter Settings
- Special Senders to Treat Differently
- Authorized Reception
- Reception File Print Quantity
- Forwarding
- Print 2 Sided
- Memory Lock
- Paper Tray
- Programming/Changing Special Senders
- Authorized RX (Authorized Reception)
- Reception File Print Qty
- Forwarding
- Print 2 Sided
- Memory Lock
- Paper Tray per Sender
- Programming Initial Set Up of a Special Sender
- Deleting a Special Sender
- Box Settings
- 5. Printer Features
- 6. Scanner Features
- 7. Registering Addresses and Users for Facsimile/Scanner Functions
- Address Book
- Registering Names
- Authentication Information
- Fax Destination
- Fax Destination
- IP-Fax Destination
- Registering an IP-Fax Destination
- Changing a Registered IP-Fax Destination
- Using the IP–Fax Destination as the sender
- To change the IP-Fax Destination
- To select the protocol
- To program the SUB Code
- To program the SEP Code
- To set the International TX Mode
- To select the fax header
- Deleting a Registered IP-Fax Destination
- E-mail Destination
- Registering Folders
- Registering Names to a Group
- Registering a Protection Code
- Registering SMTP and LDAP Authentication
- 8. Other User Tools
- 9. Appendix
- INDEX
Connecting the Machine
28
1
Settings Required to Use the Network Delivery Scanner
This section lists the settings required for delivering data to network.
Ethernet
This section lists the settings required for delivering data to network with an
Ethernet connection.
For details about how to specify the settings, see "Interface Settings" and "File
Transfer".
Note
❒ For the Effective Protocol setting, check that the protocol you want to use is
set to [Active].
❒ [LAN Type] is displayed when the wireless LAN interface board is installed.
When both ethernet and wireless LAN (IEEE 802.11b) are connected, the se-
lected interface takes precedence.
❒ If Delivery Option is set to [On], check that IPv4 Address is specified.
Reference
p.59 “Interface Settings”
p.69 “File Transfer”
Menu User Tool Setting Requirements
Interface Settings/Network Machine IPv4 Address Necessary
Interface Settings/Network IPv4 Gateway Address As required
Interface Settings/Network DNS Configuration As required
Interface Settings/Network DDNS Configuration As required
Interface Settings/Network Domain Name As required
Interface Settings/Network WINS Configuration As required
Interface Settings/Network Effective Protocol Necessary
Interface Settings/Network Ethernet Speed As required
Interface Settings/Network LAN Type Necessary
Interface Settings/Network Permit SNMPv3 Communication As required
Interface Settings/Network Permit SSL/TLS Communication As required
Interface Settings/Network Host Name As required
File Transfer Delivery Option As required
File Transfer Fax RX File Transmission As required
File Transfer Scanner Resend Interval Time As required
File Transfer Number of Scanner Resends As required