Operating instructions
Table Of Contents
- General Settings Guide
- Introduction
- Important
- Notes:
- Manuals for This Machine
- TABLE OF CONTENTS
- How to Read This Manual
- Display Panel
- Accessing User Tools
- 1. Connecting the Machine
- Connecting to the Interfaces
- Network Settings
- Settings Required to Use the Printer/LAN-Fax
- Settings Required to Use Internet Fax
- Settings Required to Use E-mail Function
- Settings Required to Use Scan to Folder Function
- Settings Required to Use the Network Delivery Scanner
- Settings Required to Use Network TWAIN Scanner
- Settings Required to Use Document Server
- Using Utilities to Make Network Settings
- Connecting the Machine to a Telephone Line and Telephone
- 2. System Settings
- 3. Copier / Document Server Features
- 4. Facsimile Features
- General Features
- Scan Settings
- Send Settings
- Reception Settings
- Initial Settings
- Reception File Setting
- Program / Change / Delete Scan Size
- Registering Fax Information
- Forwarding
- Parameter Settings
- Special Senders to Treat Differently
- Authorized Reception
- Reception File Print Quantity
- Forwarding
- Print 2 Sided
- Memory Lock
- Paper Tray
- Programming/Changing Special Senders
- Authorized RX (Authorized Reception)
- Reception File Print Qty
- Forwarding
- Print 2 Sided
- Memory Lock
- Paper Tray per Sender
- Programming Initial Set Up of a Special Sender
- Deleting a Special Sender
- Box Settings
- 5. Printer Features
- 6. Scanner Features
- 7. Registering Addresses and Users for Facsimile/Scanner Functions
- Address Book
- Registering Names
- Authentication Information
- Fax Destination
- Fax Destination
- IP-Fax Destination
- Registering an IP-Fax Destination
- Changing a Registered IP-Fax Destination
- Using the IP–Fax Destination as the sender
- To change the IP-Fax Destination
- To select the protocol
- To program the SUB Code
- To program the SEP Code
- To set the International TX Mode
- To select the fax header
- Deleting a Registered IP-Fax Destination
- E-mail Destination
- Registering Folders
- Registering Names to a Group
- Registering a Protection Code
- Registering SMTP and LDAP Authentication
- 8. Other User Tools
- 9. Appendix
- INDEX
Scanner Features
202
6
❖ Wait Time for Next Original(s): SADF
When dividing originals and scanning them separately with the ADF to form
a single file, select [Set Wait Time] or [Continuous Wait] for the waiting status.
•Continuous Wait
• Set Wait Time: 60 sec.
This setting is valid if [SADF] is specified for [Original Feed Type] when scan-
ning.
If [Set Wait Time] is selected, enter the wait time in seconds (3-999) for placing
additional originals with the number keys. Scanning will start automatically
if additional originals are placed within this time. You can end scanning and
begin transmission by pressing the {q} key within this time. Once the spec-
ified time has elapsed, transmission starts automatically.
If [Continuous Wait] is selected, the machine will wait for the additional origi-
nals until the {q} key is pressed. Scanning will start when additional origi-
nals are placed and the {Start} key is pressed. You can end scanning and begin
sending by pressing the {q} key.
Even if originals are placed on the exposure glass, the machine will operate
according to the specified settings. However, every time originals are placed
on the exposure glass, you must press the {Start} key to start scanning. Scan-
ning will start if additional originals are placed and the {Start} key is pressed
within this time. You can end scanning and begin transmission by pressing
the {q} key within this time. Once the specified time has elapsed, transmis-
sion starts automatically.
If originals are placed in the auto document feeder (ADF), transmission will
start without waiting for additional originals after all originals in the ADF
have been scanned, regardless of the specified settings.
If a paper misfeed occurs or any of the following operations are performed
while the machine is waiting for additional originals, the countdown stops
and does not start again until the {q} key is pressed.
• Changing the settings such as the scan settings
• Opening the upper cover of the ADF
•Pressing the {Interrupt} key to activate the copy mode
❖ Background Density of ADS (Full Color)
Characteristics due to the type of paper such as nonwhiteness like newspaper
or transparent originals can be reduced by correcting the scanning density.
Reference
p.3 “Accessing User Tools”
"Batch, SADF", Scanner Reference
"Items for Specifying Scan Settings", Scanner Reference
"Setting Items for Original Feed Type", Scanner Reference
"Scanning Multiple Pages of Originals as One File", Scanner Reference