Operating instructions
Table Of Contents
- General Settings Guide
- Introduction
- Important
- Notes:
- Manuals for This Machine
- TABLE OF CONTENTS
- How to Read This Manual
- Display Panel
- Accessing User Tools
- 1. Connecting the Machine
- Connecting to the Interfaces
- Network Settings
- Settings Required to Use the Printer/LAN-Fax
- Settings Required to Use Internet Fax
- Settings Required to Use E-mail Function
- Settings Required to Use Scan to Folder Function
- Settings Required to Use the Network Delivery Scanner
- Settings Required to Use Network TWAIN Scanner
- Settings Required to Use Document Server
- Using Utilities to Make Network Settings
- Connecting the Machine to a Telephone Line and Telephone
- 2. System Settings
- 3. Copier / Document Server Features
- 4. Facsimile Features
- General Features
- Scan Settings
- Send Settings
- Reception Settings
- Initial Settings
- Reception File Setting
- Program / Change / Delete Scan Size
- Registering Fax Information
- Forwarding
- Parameter Settings
- Special Senders to Treat Differently
- Authorized Reception
- Reception File Print Quantity
- Forwarding
- Print 2 Sided
- Memory Lock
- Paper Tray
- Programming/Changing Special Senders
- Authorized RX (Authorized Reception)
- Reception File Print Qty
- Forwarding
- Print 2 Sided
- Memory Lock
- Paper Tray per Sender
- Programming Initial Set Up of a Special Sender
- Deleting a Special Sender
- Box Settings
- 5. Printer Features
- 6. Scanner Features
- 7. Registering Addresses and Users for Facsimile/Scanner Functions
- Address Book
- Registering Names
- Authentication Information
- Fax Destination
- Fax Destination
- IP-Fax Destination
- Registering an IP-Fax Destination
- Changing a Registered IP-Fax Destination
- Using the IP–Fax Destination as the sender
- To change the IP-Fax Destination
- To select the protocol
- To program the SUB Code
- To program the SEP Code
- To set the International TX Mode
- To select the fax header
- Deleting a Registered IP-Fax Destination
- E-mail Destination
- Registering Folders
- Registering Names to a Group
- Registering a Protection Code
- Registering SMTP and LDAP Authentication
- 8. Other User Tools
- 9. Appendix
- INDEX
Special Senders to Treat Differently
161
4
Reception File Print Quantity
Print the specified number of copies of documents received from programmed
senders (Special Senders).
If you do not program any Special Senders, the machine prints the specified
number of copies for all received documents.
Note
❒ You cannot use multi-copy printing with Memory Lock.
❒ You can specify up to 10 copies.
Forwarding
Print received documents, and then transfer them to those receivers pro-
grammed beforehand.
Folder destination can be registered.
It is also possible to forward faxes sent only by senders programmed as Special
Senders.
Note
❒ To use this function, program your Special Senders, and then select "On" for
"Forwarding" in "Reception Settings".
❒ If you specify "On" in "Forwarding" and select [Same as Basic Settings], the fax doc-
ument is forwarded to the receivers programmed in "Specify End Receiver.".
❒ If you do not program any Special Senders, the machine transfers all incom-
ing documents to the other end receivers specified in "Specify End Receiver.".
❒ You can set the fax destination, Internet fax destination, IP-Fax destination or
folder destination, as a forward destination.
❒ Set folder destinations using the Address Book Management function under
System Settings. See "Registering Folders".
Reference
p.148 “Forwarding”
p.152 “Parameter Settings”
"Reception Settings", Facsimile Reference
Print 2 Sided
Print on both sides of the paper.
Note
❒ If you select the bypass tray for "Paper Tray", duplex printing is disabled.