Operating instructions
Table Of Contents
- General Settings Guide
- Introduction
- Important
- Notes:
- Manuals for This Machine
- TABLE OF CONTENTS
- How to Read This Manual
- Display Panel
- Accessing User Tools
- 1. Connecting the Machine
- Connecting to the Interfaces
- Network Settings
- Settings Required to Use the Printer/LAN-Fax
- Settings Required to Use Internet Fax
- Settings Required to Use E-mail Function
- Settings Required to Use Scan to Folder Function
- Settings Required to Use the Network Delivery Scanner
- Settings Required to Use Network TWAIN Scanner
- Settings Required to Use Document Server
- Using Utilities to Make Network Settings
- Connecting the Machine to a Telephone Line and Telephone
- 2. System Settings
- 3. Copier / Document Server Features
- 4. Facsimile Features
- General Features
- Scan Settings
- Send Settings
- Reception Settings
- Initial Settings
- Reception File Setting
- Program / Change / Delete Scan Size
- Registering Fax Information
- Forwarding
- Parameter Settings
- Special Senders to Treat Differently
- Authorized Reception
- Reception File Print Quantity
- Forwarding
- Print 2 Sided
- Memory Lock
- Paper Tray
- Programming/Changing Special Senders
- Authorized RX (Authorized Reception)
- Reception File Print Qty
- Forwarding
- Print 2 Sided
- Memory Lock
- Paper Tray per Sender
- Programming Initial Set Up of a Special Sender
- Deleting a Special Sender
- Box Settings
- 5. Printer Features
- 6. Scanner Features
- 7. Registering Addresses and Users for Facsimile/Scanner Functions
- Address Book
- Registering Names
- Authentication Information
- Fax Destination
- Fax Destination
- IP-Fax Destination
- Registering an IP-Fax Destination
- Changing a Registered IP-Fax Destination
- Using the IP–Fax Destination as the sender
- To change the IP-Fax Destination
- To select the protocol
- To program the SUB Code
- To program the SEP Code
- To set the International TX Mode
- To select the fax header
- Deleting a Registered IP-Fax Destination
- E-mail Destination
- Registering Folders
- Registering Names to a Group
- Registering a Protection Code
- Registering SMTP and LDAP Authentication
- 8. Other User Tools
- 9. Appendix
- INDEX
Initial Settings
137
4
❖ SIP Settings
Set the SIP server's IPv4 address or host name, and SIP user name.
If you select [On] using the User Parameters, you can use the SIP server. See
"Parameter Settings" ( switch 34, bit 1).
You can use alphanumeric symbols (lower and upper cases) and symbols (";",
"?", ":", "&", "=", "+", "$", ",", "-", "_", ".", "!", "~", "*", "#", "‘", "(", ")", "%", "/", and
"@") for registration of the SIP User Name in SIP Settings. Make sure you enter
these characters correctly.
Use numbers and periods (".") to enter the correct IPv4 addresses for the gate-
keeper, SIP server, and gateway. To obtain the correct IPv4 addresses, consult
the administrator.
A Press [Facsimile Features].
B Press [Initial Settings].
C Press [SIP Settings].
D Press [Change] for each property.
A proxy server relays call requests and responses.
A redirect server processes request destination inquiries.
A register server registers location information of user agents (which cor-
respond to telephones or facsimiles on public telephone lines) on an IP net-
work.
E Enter the IPv4 address or host name, and SIP user name, and then press
[OK].
F Specify whether to perform SIP digest authentication.
If you select [On], enter the password using up to 128 characters.
G Press [OK].
❖ Program / Change / Delete Gateway
Register, change, or delete the gateway used for transmission to IP-Fax.
• Program / Change
A Press [Facsimile Features].
B Press [Initial Settings].
C Press [Program / Change / Delete Gateway].
D Check that [Program / Change] is selected.
E Press a gateway to register.
When registering a new gateway, press [Not Programmed].