Operating instructions
Table Of Contents
- General Settings Guide
- Introduction
- Important
- Notes:
- Manuals for This Machine
- TABLE OF CONTENTS
- How to Read This Manual
- Display Panel
- Accessing User Tools
- 1. Connecting the Machine
- Connecting to the Interfaces
- Network Settings
- Settings Required to Use the Printer/LAN-Fax
- Settings Required to Use Internet Fax
- Settings Required to Use E-mail Function
- Settings Required to Use Scan to Folder Function
- Settings Required to Use the Network Delivery Scanner
- Settings Required to Use Network TWAIN Scanner
- Settings Required to Use Document Server
- Using Utilities to Make Network Settings
- Connecting the Machine to a Telephone Line and Telephone
- 2. System Settings
- 3. Copier / Document Server Features
- 4. Facsimile Features
- General Features
- Scan Settings
- Send Settings
- Reception Settings
- Initial Settings
- Reception File Setting
- Program / Change / Delete Scan Size
- Registering Fax Information
- Forwarding
- Parameter Settings
- Special Senders to Treat Differently
- Authorized Reception
- Reception File Print Quantity
- Forwarding
- Print 2 Sided
- Memory Lock
- Paper Tray
- Programming/Changing Special Senders
- Authorized RX (Authorized Reception)
- Reception File Print Qty
- Forwarding
- Print 2 Sided
- Memory Lock
- Paper Tray per Sender
- Programming Initial Set Up of a Special Sender
- Deleting a Special Sender
- Box Settings
- 5. Printer Features
- 6. Scanner Features
- 7. Registering Addresses and Users for Facsimile/Scanner Functions
- Address Book
- Registering Names
- Authentication Information
- Fax Destination
- Fax Destination
- IP-Fax Destination
- Registering an IP-Fax Destination
- Changing a Registered IP-Fax Destination
- Using the IP–Fax Destination as the sender
- To change the IP-Fax Destination
- To select the protocol
- To program the SUB Code
- To program the SEP Code
- To set the International TX Mode
- To select the fax header
- Deleting a Registered IP-Fax Destination
- E-mail Destination
- Registering Folders
- Registering Names to a Group
- Registering a Protection Code
- Registering SMTP and LDAP Authentication
- 8. Other User Tools
- 9. Appendix
- INDEX
Copier / Document Server Features
116
3
Input/Output
This section describes the user tools in the Input/Output menu under Copier /
Document Server Features.
Default settings are shown in bold type.
❖ Switch to Batch
You can select to have Batch mode or SADF mode displayed when you press
the [Special Original] key.
• Batch
•SADF
❖ SADF Auto Reset
In SADF mode, an original must be set within a specified time after the pre-
vious original has been fed.
You can adjust this time from 3 to 99 seconds in increments of 1 second.
The default setting is 5 second(s).
❖ Rotate Sort: Auto Paper Continue
Specify to continue copying when paper of the required orientation has run
out during rotate sort.
•On
Copying continues using copy paper of a different orientation. The copy
job will finish even if you have left the machine.
• Off
When paper of the required orientation runs out, the machine stops copy-
ing and prompts you to supply copy paper. After you have loaded paper,
the machine will continue copying.
❖ Memory Full Auto Scan Restart
When memory becomes full while scanning originals, the machine can make
copies of scanned originals first, and then automatically proceed scanning re-
maining originals.
•On
You can leave the machine unattended to make copies, but sorted pages
will not be sequential.
• Off
When memory becomes full, the machine stops operation allowing you to
remove the copy pages delivered on the output tray.
❖ Letterhead Setting
If you select [Yes] in this function, the machine rotates the image correctly.
•Yes
• No
Orientation-fixed (top to bottom) or two-sided paper might not be printed
correctly depending on how the originals and paper are placed.