Operating instructions
Table Of Contents
- General Settings Guide
- Introduction
- Important
- Notes:
- Manuals for This Machine
- TABLE OF CONTENTS
- How to Read This Manual
- Display Panel
- Accessing User Tools
- 1. Connecting the Machine
- Connecting to the Interfaces
- Network Settings
- Settings Required to Use the Printer/LAN-Fax
- Settings Required to Use Internet Fax
- Settings Required to Use E-mail Function
- Settings Required to Use Scan to Folder Function
- Settings Required to Use the Network Delivery Scanner
- Settings Required to Use Network TWAIN Scanner
- Settings Required to Use Document Server
- Using Utilities to Make Network Settings
- Connecting the Machine to a Telephone Line and Telephone
- 2. System Settings
- 3. Copier / Document Server Features
- 4. Facsimile Features
- General Features
- Scan Settings
- Send Settings
- Reception Settings
- Initial Settings
- Reception File Setting
- Program / Change / Delete Scan Size
- Registering Fax Information
- Forwarding
- Parameter Settings
- Special Senders to Treat Differently
- Authorized Reception
- Reception File Print Quantity
- Forwarding
- Print 2 Sided
- Memory Lock
- Paper Tray
- Programming/Changing Special Senders
- Authorized RX (Authorized Reception)
- Reception File Print Qty
- Forwarding
- Print 2 Sided
- Memory Lock
- Paper Tray per Sender
- Programming Initial Set Up of a Special Sender
- Deleting a Special Sender
- Box Settings
- 5. Printer Features
- 6. Scanner Features
- 7. Registering Addresses and Users for Facsimile/Scanner Functions
- Address Book
- Registering Names
- Authentication Information
- Fax Destination
- Fax Destination
- IP-Fax Destination
- Registering an IP-Fax Destination
- Changing a Registered IP-Fax Destination
- Using the IP–Fax Destination as the sender
- To change the IP-Fax Destination
- To select the protocol
- To program the SUB Code
- To program the SEP Code
- To set the International TX Mode
- To select the fax header
- Deleting a Registered IP-Fax Destination
- E-mail Destination
- Registering Folders
- Registering Names to a Group
- Registering a Protection Code
- Registering SMTP and LDAP Authentication
- 8. Other User Tools
- 9. Appendix
- INDEX
General Features
93
3
❖ Copy Orientation in Duplex Mode
You can set the copy orientation when making two-sided copies.
• Top to Top
•Top to Bottom
❖ Max. Copy Quantity
The maximum copy quantity can be set between 1 and 999.
The default setting is 999 sheets.
❖ Auto Tray Switching
If you load paper of the same size in two or more trays, the machine automat-
ically shifts to the other when the first tray runs out of paper (when Auto Pa-
per Select is selected.) This function is called "Auto Tray Switching". This
setting specifies whether to use Auto Tray Switching or not.
• With Image Rotation
Use to copy when using the Auto Tray Switching function.
• Without Image Rotation
Only copies with Auto Tray Switching if you load paper of the same size
and in the same orientation in two or more trays. If the paper is not the
same size or in the same orientation, copying is interrupted and the mes-
sage "Load paper." is displayed.
•Off
When a paper tray runs out of paper, copying is interrupted and the mes-
sage "Load paper." is displayed.
❖ Tone: Original Remains
The beeper (key tone) sounds if you forget to remove originals after copying.
• On
•Off
If Panel Tone of User Tools (System Settings) is [Off] the beeper does not
sound irrespective of the Tone: Original Remains setting.
❖ Job End Call
You can choose whether or not the beeper sounds when copying is complete.
If Panel Tone of User Tools (System Settings) settings is [On], the machine
beeps to notify you that it did not complete a job for reasons such as copying
was interrupted, the paper tray ran out of paper, or a paper jam occurred.
• On
•Off