Iumml FT6645/6655 Operating Instructions ‘\ / ‘k
Notes: The model names of the machines do not a pear in the following Check the type of your machine before rea Cfing this manual. (For details, see page 2.) pages. Type 1 = FT6645 Type 2 = FT6655 Certain types may not be available in some countries. For details, please contact vour local dealer. Note: Certain contact options ma not be available your local J eater. in some countries.
SAFETY INFORMATION SAFETY INFORMATION When using your copier, the following safety precautions should always be followed. Safety During Operation In this manual, all safety messages These words mean the following: are identified by the words “WARNING” WARNING: Important information to alert you to a situation that might damage to your property if instructions are not followed. Caution: Impotiant information that tells how to prevent situation that might cause minor injury.
SAFETY INFORMATION General Safety Information ~ &lways turn the copier off when you have finished . copying for the day, but leave it plugged D When the copier will not be used for a long period, disconnect Cl If the copier must be transported by vehicle, the power cord. please contact your service 5 When the main switch is in the Stand-by position, the anticondensation case of emergency, unplug the machine’s power cord. ~ The main plug on this equipment must be used to disconnect representative.
INSTALLATION REQUIREMENTS Copier Environment INSTALLATION REQUIREMENTS Copier Environment The installation location should be carefully affect the performance of a copier. - Optimum environment tJ Temperature: 10- 30”C (50 - 86°F) Cl Humidity: 15- 90?40 chosen because conditions environmental conditions greatly - D A strong and level base. 0 The copier must be level within 5 mm (0.2”) both front to rear and left to right.
Power Connection INSTALIJ4TION REQUIREMENTS Power Connection DAvoid multiwiring. Cl Make sure that the wall outlet is near the copier and easily accessible. D Make sure the plug is firmly inserted ~ Voltage must not fluctuate Cl Do not set anything in the outlet. more than 10YO. on the power cord. Access To Copier IJ Place the copier near the power source, providing clearance as shown: More than 10 cm More than 10cm *2 (3.9”) F=== Your machine --i L9”) More than 10cm *1 (3.
STORAGE OF SUPPLIES STORAGE OF SUPPLIES Storage Of Supplies Paper Storage Paper should always be stored properly, Improperly reproduction, creased copies, and paper misfeeds. stored ~ Avoid storing paper in humid areas. (Under high temperature store copy paper in a vinyl bag,) Z1Do not store paper where it will be exposed paper may result in poor image and high humidity conditions, to heat. U Store on a flat surface. 7 Use older stock first. ~ Do not lay heavy objects on paper.
TABLE OF CONTENTS TABLE OF CONTENTS GUIDE TO COMPONENTS Copier Type . . . Copier Exterior . . System Overview . Operation Panel Key Tops . Touch Panel WHAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . . . 3 . . . 4 . . . . . . . . . .6 . . . 7 . . . . . . . . . . . . . . . . . . . . . . . . . Display . . . . . . . . . . . YOU CAN DO WITH THIS COPIER . . . . . . . . . . . . .
TABLE OF CONTENTS SEITING ORIGINALS IN THE RECIRCULATING DOCUMENT HANDLER . . . . . . . . . . . . . . .31 . . . . . . . . Recommended Originals . . . . . . . . . . . . . . . . . . . . . .32 Non-recommended Originals . . . . . . . . . . , . . . . , . . . . . . . . . . . .32 . . . . . Setting Originals . . . . . . . . . . . ● ✎ SETTING BASIC ORIGINALS FUNCTIONS AND KEY TOPS sort , .,.....0.0.000. Stack . . . . . . . . . . . . Stapling Gopies. o . . . . . . Manual Staple . . . . . . . . Special Brig . . .
TABLE OF CONTENTS SPECIFICATIONS Copier . . . . . . . . . . Dual Job Feeder . . . . . . . . Compact Sorter Stapler . . . . . Floor Type Sorter Stapler . . Recirculating Document Handler Finisher . . . . . . . . . . . . . 3,500-sheet Large Capacity Tray COMBINATION INDEX CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Before reading this Operating Instructions, please refer to pages 2-5 to know which type of copier and system you have.
Copier Type GUIDE TO COMPONENTS GUIDE TO COMPONENTS Copier Type There are two types of copier. Type 1 a?, Three 550-sheet paper trays Optional 3,500-sheet large capacity 1 tray —-——---/ 550 P (3,500) 550 I I I 550 I .—— — ——— -1 Type 2 Tandem paper tray (two 500-sheet paper trays) One 550-sheet paper tray 1,500-sheet large capacity tray Optional 3,500-sheet large capacity tray ———— --- I t (3,500) * I 1 I ~-.--.
GUIDE TO COMPONENTS Copier Exterior : 8 L Copier Exterior ● ● Ss als here Ep J \ /\ ~ COPY TRAY (Option) Completed copies are delivered here. “FOR TYPE 1 550-SHEET / PAPER TRAYS These trays can hold 550 sheets of copy paper each. MAIN SWITCH Switches the copier between ON and STAND-BY. BYPASS FEED TRAY Up to 50 sheets of paper (80 g/rep, 20 lb) can be loaded at one time. You can use this tray for the Cover/Slip Sheet mode. Also, use this table when copying onto adhesive labels.
System Overview System A (Copier type 1 with dual job feeder and compact sorter stapler) Dual job feeder 1 3,500-sheet – large capacity Compact sorter stapler— tray System B (Copier type 1, or 2 with dual job feeder and floor type sorter stapler) “Illustration shows type 2. Dual job feeder . Floor type _ sorter stapler 3,500-sheet large capacity tray .
System C (Copier type 2 with recirculating document handler and finisher) Recirculating document handler I 1 i-f== Finisher L / 3,500-sheet – large capacity tray
GUIDE TO COMPONENTS Operation Operation Panel Panel Key Tops KEY Press to see guidance for functions. > See page 12. GUIDANCE I CONTRAST DIAL You can change the brightness of the display. I INTERRUPT KEY Press to make interrupt copies during a copy run. Z- See page 42. I I TOUCH PANEL DISPLAY ~ See next page. ENTER KEY Use to enter data in selected modes. I Program ~ -> , I I I I ) L ~ PROGRAM ~EY Press to select the program mode, > See page 42. NUMBER KEY Press to start copying.
GUIDE TO COMPONENTS Touch Panel Display Initial System Display A and B COPY COUNTER Indicates the number of copies. BASIC FUNCTIONS AND KEY TOPS x See page 35. OPERATION SCREENS S See page 43. System C COPY COUNTER Indicates the number of copies. BASIC FUNCTIONS AND KEY TOPS ~ See page 35. OPERATION SCREENS S Seepage 43. Keys that have the option of being selected. ~ ........................................ Keys that have been selected. 1 Keys that have no option to select.
WHAT YOU CAN DO WITH THIS COPIER WHAT YOU CAN DO WITH THIS COPIER System A and B i ~> Ready 1“ [ lEJ 81/2x 2H 11 w 8’/2X 14 w S See page 35. X See page 35. 3EI 11X17G ~ See page 35. & .Bwass Tray TEJ 8V2X 11 U See page 41. 1 Auto I I I CC ~erfSlipShyt] ( Edit Imagq ) f ~ See page 9. s See ~ page 41. L + See page 10. See * page 39. * See page 11. See ~ page 38. E See page 35. S See page 35. L-_ ~ See page 35. ~ See page 10. See page 37. System C t.
WHAT YOU CAN DO WITH THIS COPIER (“) ~hmthwrl + See pages 60-63. lPaper Ilesignatel . ., @i@@fl + .“, ..,,:..,.... ..,.,.,.,:.,... ,.:,,,,,,,. ..,. .,2 3., “456 789 IN’ Yip $hod m 1...” #, ...... .
WHAT YOU CAN DO WITH THIS COPIER (“” * See pages 56-59. IEm!!LJ Editing/ Centwing I !hveha I 1 I Erm Borderl + f I Mete AreaI /Bord. I ICent. p El El A (i-e’ l%se’t wl 10 * See page 43.
WHAT YOU CAN DO WITH THIS COPIER ~ See pages 44-55. Dupbl I m 1 + 2 ●rl:~: 1 J ,--.-’, Kl%l Combine I hnbine2Nkn. I Emml I u 1 ,’,:& + J 1 1 I Combine 4Min. I 2 + 1 =’;-.
Seeking Guidance In Stand-by HOW TO SEE THE GUIDANCE DISPLAY HOW TO SEE THE GUIDANCE DISPLAY Press the Guidance key when you want to know detailed information about functions use. You can use this key in stand-by or when entering the settings for a copy job. Seeking Guidance In Stand-by & 1. 2. Press the Clear Guidance key, key and the Touch the key you want to know about on the touch panel display. O 3. Modes The touch panel display shown at right is for systems A and B.
HOW TO SEE THE GUIDANCE DISPLAY Seeking Guidance While Entering Job Settings Seeking Guidance 1. Press the Guidance While Entering key. Job Settings I # Guidance •~ 1 n I Program● +> The information about functions you have selected just before will be displayed on the touch panel display. For example, if you have selected the Staple mode, the guidance appears as shown at right. Cl The touch panel display shown at right is for system B. 2. To exit from the Guidance touch the Exit key.
CHANGING DEFAULT SE7TINGS User Tools CHANGING DEFAULT SETTINGS User Tools This section is for the key operators in charge of this copier. copier’s default settings using the following user tools. User Tools You can change or set the Menu < User Tools> m Selectone of the folloiulng items. < User Tools> m Selectone of the followingItems. < User Tools> m Selectone of the folIowlng[terns.
CHANGING DEFAULT SEl17NGS User Tools [~[ Auto reset/Auto Auto Screen Auto The co ier returns to its initial condition automatically after our jo E is finished. The automatic reset time can be set r rom 1 second to 999 seconds, or the function can be turned off . ~ default: 60 sec. reset Saver When the machine does not detect anyone operating it for the selected time, the touch panel display turns off automatically.
User Tools CHANGING DEFAULT SEITINGS Use to set the copier’s internal clock before setting the weekly timer. the touch panel display instructions. Set the clock following 0 If necessary, remember to adjust the clock for daylight saving time (summer time), or return it to standard time. [~1 Weekly Timer Use to set the weekly timer. If you set the timer, the copier turns on and off automatically the selected time each day.
CHANGING DEFAULT SETTINGS User Tools Change fixed R/E ~[ This copier has 10 fixed ratios (4 enlargements fixed reproduction ratios to different ratios. n Set standard 7 ~ You can change these tray display When Auto Paper Select is canceled, the 1st tray is selected as a default setting. You can cancel this setting and select the other tray as a default setting. ~ default: OFF Paper Tray Priority Auto and 6 reductions). As a default setting, the Auto Paper Select is selected.
User Tools CHANGING DEFAULT SETTINGS User Tools for User Code Mode If the copier codes is set to use the User Code function, before copies the machine made under each user code. mode, please contact User tools these 8,9, your sales user tools, you should count their user of the number of . When access for the key operator input set to the User Code representative enter the key operator must you want to use code first.
Remmmended SEITING Originals SETTING ORIGINALS Recommended For this dual job feeder, the following types of originals 41-52 glmz 11 -131b 81-104 105-128 14-20 21-28 29 -34 50 30 25 A3 lengthwise * ● o * A4 lengthwise * ● o * A4 sideways * ● o 4$ * * * * A5 sideways * o B4 lengthwise * ● B5 lengthwise * ● B5 sideways * ● F (8” x 13“) lengthwise * ● 11” x 17“ lengthwise * ● 0 o o o o o 81/2” x 14“ lengthwise * ● o * 81/2”x 11” lengthwise * ● o * 8
SEITING ORIGINALS IN THE DUAL JOB FEEDER Non-recommended Caution: Non-recommended Originals The following types of originals are not recommended for use with the dual job feeder. Please place them directly on the exposure glass.
SEITING Setting A Stack Of Originals ORIGINALS IN THE DUAL JOB FEEDER Setting A Stack Of Originals Automatic Automatic (2 Sided Document Feed (ADF) mode (I Sided originals Reverse Document Feed (ARDF) mode Originals mode) mode) In this mode, the operator inserts a stack of originals of the same size into the original These originals are individually fed onto and removed from the exposure glass. 1. Correct any curl, fold, or crease in the originals before setting. Square the stack of originals.
5, Set originals face up into the dual job Original inthe Insert dicator goes off. feeder 6. until IJ The original guide must touch the front side of the originals. Cl Do not stack originals mark. Press the Start above the limit key, The bottom sheet of the original (last page) feeder first.
Setting One Original At A Time SETTING ORIGINALS IN THE DUAL JOB FEEDER Setting One Original Semi-Automatic At A Time Document Feed (SADF) mode mode, the operator inserts one original at a time into the dual job feeder. is automatically fed onto and removed from the exposure glass. In thk 1. Correct any curl, fold, or crease originals before setting. The original in the Qv 4 +@ b a 2. Confirm that the Insert Original dicator is lit before setting. 3.
SEITING 5. ORIGINALS IN THE DUAL JOB FEEDER Set the original face up into the dual job feeder until the Insert Original indicator goes off. O Start with the last page of the originals. O The original guide must touch the front side of the original. J 6. Press the Start 7. While the Auto Feed indicator is lit after an original is fed, set the next original. The original is automatically fed and copied. O key.
Setting Different Sized Originals SE7TING ORIGINALS IN THE DUAL JOB FEEDER Setting Diffe Sized Originals Mixed Sized mode In this mode, you can set originals with different feeder. You can use the following sizes: A4/A3 version: LT/DLT version: 1. Touch the Special touch panel display. widths and lengths together into the dual job A3, B4, A4 and B5 11” x 17”, 81/2” x 14”, and 81iz” x 11“ Orig. key of the (See page 41.) 2. Touch the Mixed Sizes key of the touch panel display. (See page 41.) 3.
Setting Different Sized Originals SEITING ORIGINALS IN THE DUAL JOB FEEDER 6. 7. Adjust the original widest original. guide to match the Set the originals face up into the dual feeder until the insert Original job indicator goes off. Cl Originals must be aligned to the rear-left corner of the dual job feeder, as shown. 1, — .— 7 — —J I T -Q 8. Press the Start key.
SEITING Setting A Pasted Original ORIGINALS IN THE DUAL JOB FEEDER Setting A Pasted Original Pasted Original mode In this mode, you can set a pasted original into the dual job feeder. o In this mode, you can set one original at a time. 1. Touch the Special touch panel display. Orig. key of the (See page 41.) 2. Touch the Pasted Original key of the touch panel display. (See page 41.) 3. Correct any curl, fold or crease originals before setting. in the 1 4.
SETTING ORIGINALS IN THE DUAL JOB FEEDER 7. Setting A Pasted Original Set one pasted original face Up into the dual job feeder until the Insert Original indicator O goes off. Start with the last page of originals. Cl The original guide must touch the front side of the original. 8. Press the Start key. I I 9. While the Auto Feed indicator is lit after an original is fed, set the next original. The original is automatically fed and copied. ~ While the dual job original. User Tool 10.
SETTING ORIGINALS IN THE DUAL JOB FEEDER Presetting Originals During A Copy Run Presetting 1. Originals During A Copy Run Touch the Preset key of the touch panel display. (See page 41.) Copying m You can preseta job with~ llEiD AutoImage Density 213 Iyzxlq ~ Sort 2. Following the instructions on the display, set the copy job settings for your next job. 3. Touch the Exit key of the touch panel display. The touch shown.
Presetting Originals During A Copy Run SETTING ORIGINALS IN THE DUAL JOB FEEDER 5. Touch the Exit key of the touch panel display. After your first job is finished, the next job will start automatically. ~–’”7 ,,PJ,esej,, /A[=i[ Exit Place the preset originals on top of the originals being copied, then press ~.
SEITING Recommended Originals ORIGINALS IN THE RECIRCUI,ATING DOCUMENT HANDLER SETTING ORIGINALS IN THE RECIRCULATING DOCUMENT HANDLER Recommended For this recirculating Originals document handler, 52-103 SIZE c ,-o ~ @ > 2 a u 14-27 A3 lengthwise F (8” x 13“) lengthwise the following types of originals (g/m2) (lb) can be used.
SETTING ORIGINALS IN THE RECIRCULATING Non-recommended Caution: DOCUMENT HANDLER Non-recommended Originals Originals The following types of origins/s are not recommended for use with the recirculating document handler. Please place them directly on the exposure glass.
SETTING ORIGINALS IN THE RECIRCUIJ+TING Setting Originals 3. Adjust original 4. If you have more than two originals, square the stack of originals. Set the originals face up in the original stacker. The Set Original indicator should turn off. O 5. the original width. guides DOCUMENT HANDLER to the I Originals should be the same size. Slide the feed-out unit to match the size marks on the front side of the recirculating document handler.
SEl17NG ORIGINALS ON THE EXPOSURE GIASS SETTING ORIGINALS ON THE EXPOSURE GLASS If your machine is equipped with the platen 1. Lift the platen cover. 2. Set the original face down on the exposure glass. The original must be aligned to the rear left corner. O If your Before pressing the Start key, lower the platen cover. machine is equipped with the dual job feeder 1. Lift the dual job feeder. 2. Set the original face down on the exposure glass.
BASIC FUNCTIONS AND KEY TOPS BASIC FUNCTIONS AND KEY TOPS The copier automatically controls the image density accord- ing to the original background density. 1 ,~.:x,:x I,:,::.=:: m After canceling the Auto Image Density, use these keys to adjust the image density manually. To get a darker image, touch the right keys. To get a lighter image, touch the left keys. The copier selects a suitable size of copy paper based on the original size and the reproduction ratio.
BASIC FUNCTIONS AND KEY TOPS When you have selected functions on operation screens, this key appears on the touch panel display. Touch this key to see at a glance all the modes you selected. P!zJ m After the Check Modes key is touched, this key appears on the touch panel display. Touch this key to return to the display when the Check Modes key was touched. When you select functions on the operation screens, this key appears on the touch panel display.
sort BASIC FUNCTIONS AND KEY TOPS Before using the Sort function, please refer to page 4 and 5 to know which system you have because this function is different depending on the system you have. System A and B One copy of each original is delivered to each bin and copies are collated into sets. . System C System C does not have the Sort key. As a default setting, sequential order by sliding the shift tray from side to side.
Stack BASIC FUNCTIONS AND KEY TOPS EEDm! Before using the Stack function, please refer to page 4 and 5 to know which system you have because this function is different depending on the system you have. System A and B All copies of each original System C Copies from different side to side. System are delivered to the same bin.
BASIC FUNCTIONS AND KEY TOPS Stapling Copies Stapling Copies ‘ Before using the Staple function, please refer to page 4 and 5 to know which system you have because this function is different depending on the system you have. In the Staple function, groups of copies are automatically stapled. D If you select this function, the Sort function is automatically selected.
Stapling Copies BASIC FUNCTIONS AND KEY TOPS rl Forthe Staple function, the following limitations apply: System B System C Maximum paper size A3,11’’x17” A3,11”x17° A3,11’’x Minimum paper size B5, 8112°x 11” B5, 8112°x 11“ B5, 8112”x 11” Maximum paper weight 80 g/mz, 20 lb 80 g/mz, 20 lb 80 g/mz, 20 lb 52 g/m2, 14 lb 64 g/m2, 17 lb 64 g/m2, 17 lb Minimum paper weight 1 A4, 81/2” x 11” or smaller: from 2 to 20 sheets Stapler capacity all sizes: from 2 to 50 sheets B4, 8112°x 14“ or larg
BASIC FUNCTIONS AND KEY TOPS [ This key can be used only when you have system A or B. You can staple copies sorted in bins after copying I is finished. (This key has two functions. 1 This key can be used only when your machine DiEEiEl is equipped with the dual job feeder (system A or B). I Use this key when you want to set the different sized together in the dual job feeder. The machine automatically detects the size of each original to be fed.
BASIC FUNCTIONS AND KEY TOPS w ● Program ● t> You can store up to 5 frequently for future use. v used copy job settings in machine memory, and recall them O You can select the Program N0,5 as a default setting using the User Tool 5. See page 16. Entering a program 1. Set the copy settings you want to put into memory. 2. Press the Program key. 3. Follow the instructions on the touch panel display. Recalling a program 1. Press the Program key. 2. Follow the instructions on the touch panel display.
Reduce/Enlarge FUNCTIONS FUNCTIONS ON OPERATION SCREENS ON OPERATION SCREENS You can select one of 10 preset ratios. 6 reduction ratios and 4 enlargement ratios are preset. O You can change the fixed ratios using User Tool 6. See page 17. The reproduction ratio can be changed from 50% to 200?10in 10/0steps. There are two ways to change ratios. El El ‘efau’t Il?!k?w Input the desired ber keys.
Duplex/Series Copies (Duplex) FUNCTIONS ON OPERATION SCREENS I 1 mm Before using this function, please refer to page 4 and 5 to know function is different depending on the system you have. which system you have because this O A right margin (5 mm, 0.2”) is set on the back side automatically.
Duplex/Series Copies (Duplex) FUNCTIONS ON OPERATION SCREENS Select this key if the number of originals is even. this key if the number of originals is odd.
Duplex/Series Copies (Duplex~ FUNCTIONS ON OPERATION SCREENS System C . If your machine is equipped with the recirculating document handler (system C), the Autocount function is default. Do the following. 1. 2. Set the stack of originals face up in the recirculating document handler. Press the Start key. The machine starts counting originals. After counting is finished, copying start automatically. will lJN!wLl t 11.
Duplex/Series Copies (Duplex) FUNCTIONS ON OPERATION SCREENS mmml This function makes 2 sided copies from 2 sided originals. When you set originals in the dual job feeder, the last page of the originals should be on the bottom as shown. When you set originals in the recirculating document handler, the last page of the originals should be on the bottom as shown .
Duplex/Series Copies (Series Duplex~ FUNCTIONS ON OPERATION SCREENS w Qm IJ The following functions cannot be used if copy paper larger than A4 sideways or 8112” x 11” sideways is selected. o The center of an original is determined according to the selected copy paper and reproduction ratio. Make sure to select copy paper and reproduction ratio suitable for the original. This function makes 2 sided copies from 2 facing pages of a bound (book) original.
Duplex/Series Copies (Series Duplex) FUNCTIONS ON OPERATION SCREENS Use this function to have the copies face each other exactly as the bound (book) originals do. When you use this function, place the original on the exposure glass face down. For bound originals read from left to right, place the original on the exposure glass with the cover right side up. You should start with the last page of the originals and the last page should be aligned to the left scale as shown.
FUNCTIONS ON OPERATION SCREENS Duplex/Series Copies (Series Copies~ I Book+l$iM 2$idod +I$idod This function makes 1 sided copies from two facing pages of bound (book) originals. Cl This function cannot be used if copy paper larger than A4 sideways or 81/2” x 11” sideways is selected. O The center of an original is determined according to the selected copy paper and reproduction sure to select copy paper and reproduction ratio suitable for the original. ratio.
LJlll When you set originals in the dual job feeder, the last page of the originals should be on the bottom as shown. ’234 When you set originals in the recirculating document handler, the last page of the originals should be on the bottom as shown.
Duplex/Series Copies (Combine) FUNCTIONS ON OPERATION SCREENS I - ~ htocount r Lven I Combine2 Origs. Combine4 Orixs. 7--R I-MEL!mm Odd The Combine function can be used only when your machine is equipped with the dual job feeder (system - A or B). Cl When using the Combine functions, please select the copy paper size below.
FUNCTIONS ON OPERATION SCREENS Duplex/Series Copies (Combine) 1 I I L z Select this key if the number I I I I 1 @ of originals I is even. When you set originals in the dual job feeder, the last page of the originals should be on the bottom as shown.
FUNCTIONS ON OPERATION SCREENS Duplex/Series Copies (Combine) 5 Select this key if the number I I I I I 54 of originals is odd.
FUNCTIONS ON OPERATION SCREENS Duplex/Series Copies (Combine) This function makes one 2 sided copy from four 1 sided originals. O After selecting the Combine 4 Origs. function, you have to select the Autocount key or Number keys key to input the number of originals. Example: A- Number of originals: 7 When using the dual job feeder, the last page of the originals should be on the bottom as shown.
When making copies in the Editing/Centering mode, set the originals or the recirculating document handler as shown. P . . . 1 T!N in the dual ,.. iob feeder .___— \\” When making co~ies in the Editing/Centering mode, place the original on the exposure glass as shown. O In the Save Area and the Delete Area modes, the designated line will vary by f5 mm ( + 0.2”). Therefore, leave at least 5 mm (0.2”) between the designated line and the image.
FUNCTIONS ON OPERATION SCREENS Edit Image(Editing/Centering] This function centers image on the copy.
FUNCTIONS ON OPERATION SCREENS Edit Image (Margin Adj.) You can make margins by shifting the image to the left or right, and towards the top or bottom. This function is convenient when binding copies. o A41A3 version Maximum margin width: Left and right: Top and bottom: 16 mm in 1 mm steps 15 mm in 2.5 mm steps Cl LT/DLT version Maximum margin width: Left and right: Top and bottom: 0.6” in 0.1” steps 0.6” in 0.1” steps o When you make 2 sided copies from 1 sided originals, a right margin (5 mm, 0.
Cover/Slip Sheet (Front Cover) FUNCTIONS ON OPERATION SCREENS Cover mode The Front Cover function can be used only when your machine document handler (system C). tem A or B) or the recirculating is equipped with the dual job feeder (sys- Cl ~5hen using the Front Cover function, you should set the tray for cover sheets using User Tool 2. See page Cl You can also select the bypass feed tray for cover sheets.
The Fron~Back feeder (system Covers function can be used only when your machi~e document hand/er (system A or B), or the recirculating is equipped C). with the dual job ~ When using the Front/Back Covers function, you should set the tray for cover sheets using User Tool 2. See page 15. 0 You can also select the bypass feed tray for cover sheets.
FUNCTIONS ON OPERATION The Paper Designate (system function Cover/Slip Sheet (Paper Designate) SCREENS can be used only when your machine A or B), or the recirculating document handler (system is equipped Before using this function, function is different please refer to pages 4 and 5 to know which system depending on the system you have. System A and B (with dual job feeder) After selecting this function, you have to select the Autocount to input the number with the dual job feeder C).
FUNCTIONS ON OPERATION SCREENS Cover/Slip Sheet (OHP Slip Sheet) m o ~5hen using the OHP slip sheet function, you should set the tray for slip sheets using User Tool 2. See page o You can also select the bypass feed tray for slip sheets. In this case, make sure to set paper for slip sheets that are identical in size and direction with the paper to which you are copying, because the machine cannot detect the length of paper set in the bypass feed tray.
LOADING PAPER LOADING The following PAPER paper sizes can be set.
LOADING PAPER “L” means lengthwise. “S” means sideways. O can be used for A4A3 version machines. ● can be used for LT/DLT version machines. O*: 2 sets of 500 sheets can be set in A4/A3 version machines. ●*: 2 sets of 500 sheets can be set in LT/DLT version machines. e can be set by your sewice representative for A4A3 version machines. * can be set by your servioe representative for LT/DLT version machines. o You can change the paper size of the 2nd feed station and bypass feed tray.
LOADING PAPER 550-sheet 550-sheet Paper Tray Paper Tray OForcopiertypel (lst,2nd and3rd feed station) For copier type 2 (2nd feed station) Cl You can change the paper size of the 2nd feed station. See page 73. 1. Pull out the paper tray until it stops. 2. Load paper in the paper tray. 3. O The paper stack must be flush with the right side of the paper tray. O Make sure to read the notice on the package showing the front side (copy side) of the paper. Load paper with the copy side down.
LOADING PAPER Tandem Paper Tray Tandem Paper Tray IJ For copier type 2 (1st feed station) Cl Before loading paper inthetandem tray, refer tothefollowing flowchati. Have you set A4 sideways, B5 sideways, or 81/2” x 11” sideways paper? YES NO 4 Was the whole tray pulled out or only the left part? The whole tray was pulled out. Follow the procedure below. Follow the procedures on page 66. Left part of the tray was pulled out. Follow the procedure on page 68. If the whole tray is pulled out: 1.
LOADING PAPER 2. 3. Load paper paper tray. Tandem Paper Tray in the right part of the O The paper stack must be flush with the right side of the paper tray. Cl Do not stack paper over the limit mark, D Make sure to read the notice on the package showing the front side (copy side) of the paper. Load paper with the copy side down. Push the tray until it stops. [f left part of the tray is pulled out: 1. 2. 68 Load paper in the left part of the paper tray.
LOADING PAPER 1,500-sheet Large Capacity Tray 1,500-sheet Large Capacity Tray o For copier type 2 (3rd feed station) 1. Press the Down key to lower the bottemplate. The Down keystarts blinking. Cf If paper has run out, the bottom plate lowers automatically and the Down key is lit. In this case, you need not press the Down key. 2. After the Down key stops blinking and lights, pull out the tray until it stops. 3. Load paper in the paper tray.
Optional 3,500-sheet Large Capacity Tray LOADING PAPER 3. Push the tray until it stops. Optional 1. When opening the cover, hold it by the lip. Press the Down key to lower the bottom plate. The Down key starts blinking. ~ 3. Large Capacity Open the cover of the large capacity tray. O 2. 3,500-sheet If paper has run out, the bottom plate lowers automatically and the Down key is lit. In this case, you need not press the Down key.
LOADING PAPER Bypass Feed Tray 4. Repeat steps 2 and 3. 5. Close the cover. Bypass Feed Tray 1. Open the bypass feed tray. 2. Slide the paper width. 3. If you use copy paper larger than A4 sideways or 8112° x 11” sideways, pull out the paper support guide.
LOADING PAPER 4, Insert the copy paper. O 5. 72 Make sure to read the notice on the package showing the front side (copy side) of the paper. Load paper with the mpy side up. After copying is completed, bypass feed tray.
CHANGING PAPER SIZE CHANGING PAPER SIZE o You can change the pa~~ size of the 2nd tray. If you want to change the paper size of other trays, please contact your sales or serwce representative. 1. Pull out the stops. 2. Remove 2nd paper tray until it copy paper. I 3. While pressing the release lever on the front side guide, slide the front and rear guides to the paper size you want to use. 4.
5. Select the paper size by adjusting the paper size selector on the back side of the tray. 6. Load paper. Cl The paper stack must be flush with the right side of the tray. O Do not stack paper over the limit mark. IJ Make sure to read the notice on the package showing the front side (copy side) of the paper. Load paper with the copy side down. 7. Adjust the front, rear and left guides flush with the paper stack. 8. Push the tray until it stops.
WHAT TO DO WHEN THINGS GO WRONG WHAT TO DO WHEN THINGS GO WRONG Action Problem Nothing happens when the main switch IS turned on. Check the The Start key does not change from red to green after the main switch is turned on? or the machine stops during a copy run. Check the touch panel display, instructions. Problem Copies appear dirty. The reverse side of an original image is copied. power cord. it firmly into the outlet. Cause Image density dark. Image density dark.
USER REMARKS Problem Staples all. do not come out at Cause Action You loaded the new staple cartridge. After loading the new staple cartridge, staples may not be ejected the first few times you try to use the stapler. There are “ammed staples in the stap t er. Compact sorter stapler (system A) > Remove the jammed staples following the instructions inside the sorter stapler cover Floor type sorter stapler (system B) > Call your sewice representative.
DO’S AND DON’TS DO’S AND DON’TS WHEN ADDING TONER WARNING: [ WARNING: Do not incinerate toner or toner when exposed to open flame. Dispose of the used toner cartridge Cl When adding toner, follow the instructions IJ Do not turn off the main switch. containers. Toner according dust to your may ignite local on the touch panel display. If you do, your copy settings are cleared.
Platen Cover DAILY MAINTENANCE Copier DAILY MAINTENANCE To maintain high copy quality, clean the following Copier Touch Panel Display Clean the touch dry SOft cloth. Exposure panel display with a Glass 1. Lift the platen cover, dual job feeder or recirculating document handler. 2. Clean the exposure glass with a damp cloth and wipe it with a dry cloth. 0 If stains do not come off, use a glass cleaner. After using a glass cleaner, wipe it with a dry cloth. Platen Cover 1.
Dual Job Feeder DAILY MAINTENANCE Dual Job Feeder Belt 1. Lift the dual job feeder. 2. Clean the belt with adamp wipe it with a dry cloth. 0 cloth and If stains do not come off, use belt cleaner. Feed-in Unit Clean the original table and original guide with a damp cloth and wipe them with a dry cloth.
Recirculating Document Handler DAILY MAINTENANCE Recirculating Document Belt 1. Lift the recirculating ler. 2. Clean the belt with a damp cloth and wipe it with a dry cloth. Cl document hand- If stains do not come off, use belt cleaner. Feed-in Unit Clean the original stacker and original guides with a damp cloth and wipe them with a dry cloth.
SPECIFICATIONS Copier SPECIFICATIONS Copier Configuration: Console Process: Dry electrostatic Originals: Sheet, book Original Size: transfer A3,11’’x17° Maximum: Copy Paper Size: See pages 64 and 65. Copy Paper Weight: Paper tray: Bypass feed tray: Duplex copying: Copy Paper Capacity: See pages 64 and 65.
Copier SPECIFICATIONS Reproduction Ratio: I A4/A3version I I 50% I 65’ZO Enlargement Full Size Reduction LT/DLT version 1 I 50% [ I 65% 1 71 ‘!40 74!40 75?40 77% 82V0 85?lo 93’-%0 93% 100% 100% 115% 121 !40 12270 129% 141 Yo 155?40 I 200?40 Power Consumption: I 200?40 1 Type 1 and 2 I Copier only I I Warm-up I 0.9 KVA Stand-by I 0.25 KVA 1 I Copying Maximum 1 I 1.2 KVA 1.45 KVA Full system* I I , I 0.9 KVA 0.25 KVA 1.3 KVA 1.
SPECIFICATIONS Copier Noise Emission Sound pressure level: The measurements are made according to 1s07779.
Copier SPECIFICATIONS Weight: Type 1 Weight Copier (;:!./L) Copier with dual job feeder, compact sorter stapler, 3,500-sheet large capacity tray 205,8 kg (453.7 lb) Copier with dual job feeder, floor type soder stapler, 3,500-sheet large capacity tray 235.8 kg (51 9.8 lb) Type 2 Weight Copier (&?&) t I Copier with dual job feeder, floor type sorter stapler, 3,500-sheet large capacity tray I 247.8 kg (546.
SPECIFICATIONS Dual Job Feeder Dual Job Feeder Original Size: See page 19. Original Weight: See page 19, Original Table Original Feed: Automatic document feed (ADF) mode Automatic reverse document feed (ARDF) mode Semi-automatic document feed (SADF) mode Mixed sized mode Pasted original mode Preset mode Original Set: Face up, first sheet on top Original Transport: One flat belt Capacity: See page 19. Power Source: DC 24V, less than 2A (average) Power Consumption: 70 w 13 kg (28.
Compact Sorter Stapler SPECIFICATIONS Compact Sorter Stapler Paper Size for Bins: See pages 37 and 38. Paper Weight See pages 37 and 38. for Bins: Bin Capacity: See pages 37 and 38. Number of Bins: 20 bins + proof tray Stapler Capacity: Stapling See page 40.
Floor Type Sorter Stapler SPECIFICATIONS Floor Type Sorter Stapler Paper for Proof Tray: Size: Maximum: A3,11’’x I7° Minimum: A6 lengthwise, 52-157 g/mZ,14-42ib Weight: 51/2’ x 81/2” Paper for Bins: Sort mode: Stack mode: Staple mode: See page 37. See page 38. See page 39, Paper Capacity: Proof tray: Bins: 250 sheets (80 g/mz, 20 lb) Sod mode: See page 37. Stack mode: See page 38. Staple mode: See page 39. Stapler See page 40.
Recirculating Document Handier SPECIFICATIONS Recirculating Document Original Size: See page 31. Original Weight: See page 31. Handler Number of Originals to be Set: See page 31. Original Feed: RDH mode (1 sided original Original Set: Face up, first sheet on top Original Transport: One flat belt Power Source: DC 24V (from copier) Power Consumption: 70 w 88 2 sided 18 kg (39.7 lb) Weight: Dimensions mode, (W x D x H): 645 x 516 x 132 mm (25.4” x 20.3” x 5.
SPECIFICATIONS Finisher Finisher Sort (default) Paper Size: mode: See page 37, ●When the shift tray is not shifted, A6 can be stacked. Stack mode: See page 38. mode: See page 40. Paper Weight: Sort (default) mode: Stack mode: Staple mode: See page 37. See page 38. See page 40. Paper Capacity: Sort (default) mode: Stack mode: Staple mode: See page 37. See page 38. See page 40. Staple .—. ..
3,500-sheet Large Capacity Tray SPECIFICATIONS 3,500-sheet Large Capacity Tray Copy Paper Size: See pages 64 and 65. Copy 64-105 g/mz,16-241b 5V (from Paper Weight: Power Source: DC 24V, Power Consumption: 40 w Dimensions (W x D x H): 90 403 x 529 x 608 mm (1 5.9” X 20.8” X 23.9”) 19.8 kg (43.7 lb) Weight: Cl Specifications copier) are subject to change without notice.
91
COMBINATION CHART COMBINATION CHART This combination chart shows which modes can be used toqether. O means that these modes can be used tdgether. . means that one of these modes will be selected automatically. X means that these modes cannot be used together. I Edit Image 2 1 @ F g + .z ● 3 4 Reduce/Enlarge 5 7 8 9 ● ● o ● o 0 0 ● ● o ● o 0 0 1 Save Area 2 Delete Area 3 4 Erase Border ● ● Cent./Bord.
1 Duplex/Series Copies ~ Finishing ~ Cover/Slip Sheet \ Special ETC.
INDEX INDEX A Access To Copier, iv Accessing user tools, 14 ADF mode, 21 ARDF mode, 21 Auto Image Density key, 35 Auto Off, 15 Auto Paper Select, 17 Auto Paper Select key, 35 Auto Paper Select Priority, 17 Auto Reduce/Enlarge key, 35 Auto reset, 15 Auto reset/Auto off Auto Off, ~5 Auto reset, 15 SADF Auto reset, 15 Screen Saver, 15 Auto Start mode, 42 Auto Tray Switching, 17 Autocount key, 44, 52,55,62 Automatic Document Feed mode, 21 Automatic Reverse Document Feed mode, 21 B Back key, 59 BASIC FUNCTIONS
F 0 Feed-in Unit, 79-80 Finisher, 5, 89 Floor type sorter stapler, 4,87 from 1 sided originals to 2 sided copy, 11 from 2 sided original to 1 sided copies, 11 from 2 sided original to 2 sided copy, 11 from book original to 1 sided copies, 11 Front Cover key, 9, 60 Front doors, 3 Front key, 59 Front/Back key, 9,61 Full Size (100Y0) key, 35 FUNCTIONS ON OPERATION SCREENS, 43-63 Odd key, 45, 54 OHP Slip Sheet key, 9, 63 Operation panel, 3, 6 Key Tops, 6 Touch Panel Display, 7 Operation screens, 43-63 Option
Original Count Display, 17 Thin Paper mode, 17 Select special tray Tray Display for Cover Sheet, 15 Tray Display for Slip Sheet, 15 Tray for Cover Sheet, 15 Tray for Slip Sheet, 15 Select Tray key, 35 Semi-Automatic Document Feed mode, 23 Series Copies key, 11, 50 2 Sided ~ 1 Sided key, 11, 51 Book -1 Sided key, 11, 50 Series Duplex key, 11,48 Multi key, 11 Single key, 11 Set date/time, 16 Set operation modes Default Setting, 16 Image Density Level, 16 Job End Call, 16 Maximum copy input number, 16 Panel be
In accordance with ISO Standard 7001, this machine uses the following symbols for the main switch: I o means POWER ON. means POWER OFF. I u means STAND BY. Note to users in the United States of America Warning: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part.15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
RICOHCOMPANY,LTD.
