eWriter Solutions ® Ricoh eQuill Tablet User’s Guide Version 1.0.
Copyright © 2012 Ricoh Company, Ltd. Trademarks The trademark "Ricoh" and any Ricoh business names, products or services used, quoted and/or referenced within this publication are trademarks or registered trademarks of Ricoh Company, Ltd., and other company names and product names used, quoted and/or referenced may be protected as their respective trade name, trademarks or registered trademarks (collectively, "Marks").
Contents Chapter 1 Safety and Compliance Information ............................................................7 1.1 - Conventions ........................................................................................................................................ 7 1.2 - Warnings.............................................................................................................................................. 8 1.3 - Tablet Orientation.........................................................
2.3.4 - Step 4 — Open a Document ................................................................................................25 2.3.5 - Step 5 — Write On It ............................................................................................................25 2.3.6 - Step 6 — Submit for One-button Routing.........................................................................25 2.4 - Commonly Used Functions and Features............................................................................
.4 - Software Update via OTA ...............................................................................................................42 Chapter 6 Settings Page .............................................................................................. 45 6.1 - Settings Page Overview ...................................................................................................................46 6.1.1 - General Settings .........................................................................
Page 6 Version 1.0.
C H APT E R 1 Safety and Compliance Information Read all instructions and safety information before use to avoid injury. 1.1 - Conventions In this manual, the following important conventions are used: Warning Indicates a potentially hazardous situation which, if instructions are not followed, could result in death or serious injury. Caution Indicates a potentially hazardous situation which, if instructions are not followed, may result in minor or moderate injury or damage to property.
CHAPTER 1 : Safety and Compliance Information 1.2 - Warnings This device is not a device intended for use in the diagnosis of disease or other conditions, or in the cure, mitigation, treatment, or prevention of disease, in man or other animals. The AC adapter and power cord, available from Ricoh EWS, is for use with this device only. Do not use the AC adapter with other equipment. Doing so may result in fire, electric shock, or injury.
CHAPTER 1 : Safety and Compliance Information 1.4 - Battery Safety The rechargeable battery in your Ricoh eQuill tablet should be replaced only by an authorized service provider. Charge the battery only in temperatures that range from 32° to 95° Fahrenheit (0° to 35° Celsius). Caution Failure to follow this safety instruction could result in fire, electric shock, or other injury or damage. Use a Ricoh-approved powered USB port charger to charge your battery.
CHAPTER 1 : Safety and Compliance Information While most modern electronic equipment is shielded from external RF signals, if in doubt, check with the manufacturer. For personal medical devices (such as pacemakers and hearing aids), consult with your physician or the manufacturer to determine if they are adequately shielded from external RF signals. Caution Failure to follow these safety instructions could interfere with the communication of other sensitive electronic devices. 1.
CHAPTER 1 : Safety and Compliance Information 1.8 - FCC Information 1.8.1 - Declaration of Conformity Product Name Electric Writing Tablet Computer Electric Writing Tablet Computer Model Number eQ101/ Ricoh eQuill Nomad+Wi-Fi eQ102/ Ricoh eQuill Wi-Fi Responsible Party Ricoh EWS Address 2077 Gateway Place, Suite 200 San Jose, CA 95110 Telephone Number 1.855.Go-eWriter (1.855.463.9748) 1.8.
CHAPTER 1 : Safety and Compliance Information 1.8.4 - Wireless Device Caution Operation is subject to the following two conditions: (1) the wireless device may not cause interference, and (2) the wireless device must accept any interference, including interference that may cause undesired operation of the wireless device. 1.8.
CHAPTER 1 : Safety and Compliance Information 1.8.7 - Guidance on EMC Compatibility There is a shared responsibility between manufacturers, customers, and users to ensure that medical equipment and systems are designed and operated as intended. Medical electrical equipment requires precautions regarding electromagnetic compatibility, and must be installed and used according to the electromagnetic compatibility information provided in this manual.
CHAPTER 1 : Safety and Compliance Information Page 14 Version 1.0.
CHAPTER 1 : Safety and Compliance Information Ricoh eQuill Tablet | Version 1.0.
CHAPTER 1 : Safety and Compliance Information 3. Safety Information Summary Safety Information When using this product, the following safety precautions should always be followed. Safety During Operation In this manual, the following important symbols are used: R WARNING: Indicates a potentially hazardous situation which, if instrucions are not followed, could result in death or serious injury.
CHAPTER 1 : Safety and Compliance Information Notes to users of individual medical devices R WARNING: s This product emits electromagnetic waves. If you use an individual medical device (pacemaker, hearing aid, etc.), consult your doctor before using this product. If you detect an abnormality, keep some distance from the product. IMPORTANT: s To ensure safe and proper use, be sure to read the Ricoh eQuill User’s Guide before using this product.
CHAPTER 1 : Safety and Compliance Information 1.11 - Special Handling California Best Management Practices Regulations for Perchlorate Materials: “Perchlorate Material — special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate” Page 18 Version 1.0.
C H APT E R 2 Getting Started ”About this Manual” on page 19 ”Introduction to the Ricoh eQuill Tablet” on page 20 ”Getting Started — First Use” on page 22 ”Commonly Used Functions and Features” on page 26 2.1 - About this Manual This manual is written for end users of the Ricoh eQuill® tablet.
CHAPTER 2 : Getting Started 2.2 - Introduction to the Ricoh eQuill Tablet The Ricoh eQuill tablet is a portable, lightweight tablet designed to replace pencil and paper wherever you use a clipboard, scanner, or fax. The tablet improves business efficiencies by moving paper processes online.
CHAPTER 2 : Getting Started 2.2.1 - Ricoh eQuill Layout Figure 2-2: Ricoh eQuill Tablet Layout 13 14 1 1 Display 5 Backward Page Flip Button 9 On/Off Switch 13 Speaker 2 Camera Display 6 Forward Page Flip Button 10 Charging Contact (multi-unit charger) 14 Microphone 3 Shutter Button 7 Power Connector/USB 11 Accessory Plug 4 Submit Button 8 LED Indicator 12 Camera Lens Ricoh eQuill Tablet | Version 1.0.
CHAPTER 2 : Getting Started 2.2.2 - Features Camera — The Ricoh eQuill tablet is equipped with a point and shoot auto-focus camera. The camera takes 5 Megapixel color photos that are shown on the main display in black and white. E Ink® Display — The display is a high reflectance, high contrast thin film transistor (TFT) electrophoretic display for excellent reading and writing. The size is 9.7” measured diagonally. The display resolution is 1200 x 825 pixels.
CHAPTER 2 : Getting Started NOTE: If the LED blinks red three times, or there is no blinking, charge the unit. When fully charged, the LED light will be solid blue. c. When the tablet is ready for use, the LED light will stop blinking. d. (Optional step depending on your system) If you are presented with a login screen, log in using the password supplied by your administrator. e. Your Inbox Page should load. Figure 2-3 shows a sample Inbox Page.
CHAPTER 2 : Getting Started Item Icon Description Settings Brings up the Settings page. See ”Settings Page” on page 45. Use this page to view information and make modifications to the tablet. Wireless/3G Signal* Displays wireless or 3G signal strength, depending on the connection. For 3G, “R” indicates roaming. Battery* Battery (power) strength. See ”Battery Power Indicator” on page 26. Delete Delete document(s) selected with the checkbox. See ”Deleting a Document” on page 27.
CHAPTER 2 : Getting Started To calibrate: a. Start at the Inbox Page. b. Tap on the Settings icon then tap on Tools. c. Tap Calibrate. e. The Calibration screen will appear. Follow the on-screen instructions. f. Once the calibration is completed, the tablet will return to the Tools page. 2.3.4 - Step 4 — Open a Document a. Tap on an Inbox document name to open it. If there are no documents available, see your administrator to have documents uploaded to your Inbox. b.
CHAPTER 2 : Getting Started 2.4 - Commonly Used Functions and Features ”Turning Off the Tablet” on page 26 ”Sleep Mode” on page 26 ”Battery Power Indicator” on page 26 ”LED Lights” on page 27 ”Opening Blank Forms” on page 27 ”Deleting a Document” on page 27 ”Syncing the Tablet” on page 28 2.4.1 - Turning Off the Tablet Slide the On/Off button (top of tablet), and hold for seven seconds. The LED will begin blinking. Release the power button.
CHAPTER 2 : Getting Started Icon Battery Power (%) 0 - 19 20 - 39 40 - 59 60 - 79 81 - 100 2.4.4 - LED Lights LED In normal tablet use, LEDs will only be used during booting, shutting down, and charging. When in use, blinking LEDs indicate tablet status. When off, you will only see solid LEDs, indicating charging status. See ”LED Lights Interpretation” on page 69 2.4.5 - Opening Blank Forms Blank forms are assigned to a specific Ricoh eQuill Inbox (user account) accessible by the Blank Forms icon.
CHAPTER 2 : Getting Started action is completed. Tap “Yes” to delete the document, or tap “No” to cancel deletion. Multiple documents can be selected and deleted in one operation. 2.4.7 - Syncing the Tablet The sync (synchronize) function can be used to initiate the process of uploading documents to the server. Use sync instead of waiting for the default sync time, which is 20 minutes (configurable). To sync the tablet: 1. Tap the Sync Start icon. 2.
C H APT E R 3 Package Contents and Accessories ”Package Contents” on page 30 ”Stylus Tether Cord Attachment” on page 31 ”Accessories” on page 33 ”Using the Multi-Unit Charger” on page 34 Ricoh eQuill Tablet | Version 1.0.
CHAPTER 3 : Package Contents and Accessories 3.1 - Package Contents Your Ricoh eQuill tablet package contains the following items: Ricoh eQuill Tablet Stylus Stylus Tether and Stylus Holder The Stylus Holder can be inserted into either side of the tablet by removing the Accessory Plug (item #11, in Figure 2-2 on page 21). See the following section for instructions. Page 30 Version 1.0.
CHAPTER 3 : Package Contents and Accessories 3.2 - Stylus Tether Cord Attachment The tether cord can be used to attach the stylus to either the tablet (Option 1) or to the tablet cover (Option 2). 3.2.1 - Option 1: Stylus Attachment to Tablet 1. Thread one loop of the Tether Cord through the Stylus eyelet hole. 2. Thread the other loop of the Tether Cord through the loop in step 1, and pull taut. Eyelet loops Loop Stylus Stylus Hook Tether Cord 3.
CHAPTER 3 : Package Contents and Accessories Accessory Plug Slot (x2) Ridges Stylus Holder Stylus Hook Stylus Holder (enlarged view) Note the three ridges which provide friction gripping to the accessory slot 3.2.2 - Option 2: Stylus Attachment to Tablet Cover 1. Thread one loop of the Tether Cord through the Stylus eyelet hole. 2. Thread the other loop of the Tether Cord through the loop in step 1, and pull taut. Page 32 Version 1.0.
CHAPTER 3 : Package Contents and Accessories loop Tether Cord Stylus Tablet Cover Stylus Holder loop Cover Tether Holder 3. Thread the remaining loop through the Cover Tether Holder eyelet, insert the Stylus through the loop, and pull taut. 4. Insert the Stylus into the Stylus Holder (cylindrical slot located at the top of the cover). 5. To secure, hook the Stylus in the Stylus Holder. 3.
CHAPTER 3 : Package Contents and Accessories Caution Properly shielded and grounded cables and connectors must be used for connections to the tablet computer (and/or peripheral) in order to meet FCC emission limits. Only Ricoh EWS supplied cables should be used. 3.4 - Using the Multi-Unit Charger The Multi-Unit Charger is an accessory that charges up to five tablets at a time. Tablets can be charged in a Ricoh case or without a case. The Multi-Unit Charger operates on 120 Volts AC (alternating current).
CHAPTER 3 : Package Contents and Accessories Unplug the device before placing your hands or other item near the power pins. Do not operate the device if its enclosure or plug is damaged. When using this device, do not exceed the values specified by the manufacturer. Disconnect the Multi-Unit Charger power cord when not in use. Do not expose the device to dripping or splashing water. The maximum ambient temperature for this device is 400C.
CHAPTER 3 : Package Contents and Accessories 2. Orient the tablets so the three pins on the tablets match the pins on the charger. 3. The lights on the tablet, indicate the level of charge. A solid blue light indicates that the tablet is fully charged. For more information see “LED Lights Interpretation” on page 69. Page 36 Version 1.0.
C H APT E R 4 Warranty 4.1 - RICOH LIMITED WARRANTY Ricoh Innovations, Inc. (“RICOH EWS”) warrants that the Ricoh eQuill (“Device”) will be free from defects in materials and workmanship for a period of one (1) year from the date of end user purchase (“Warranty Period”).
CHAPTER 4 : Warranty The Ricoh Limited Warranty only applies to the Device. The Ricoh Limited Warranty does not apply to the accessories, batteries and other consumables provided, nor data stored on the Device. The Ricoh Limited Warranty is only valid in the country in which the Device was purchased by end user. Parts essential to the servicing of the Device shall be available for a period of three (3) years after the Device is discontinued.
CHAPTER 4 : Warranty 4.2 - Technical Assistance For technical assistance and product return authorization, and to order parts, accessories, or manuals contact Ricoh Innovations EWS. 1-855-GO-EWRITER (1-855-463-9748) support@ricoh-ews.com For additional technical assistance, technical training, and product information, visit the web site at www.ricoh-ews.com. Send all authorized, prepaid returns to the following address: Ricoh EWS 2077 Gateway Place San Jose, CA 95110 USA Ricoh eQuill Tablet | Version 1.
CHAPTER 4 : Warranty Page 40 Version 1.0.
C H APT E R 5 Ricoh eQuill Tablet Care ”Instructions for Care” on page 42 ”Camera Care” on page 42 ”Storage Requirements” on page 42 ”Software Update via OTA” on page 42 Ricoh eQuill Tablet | Version 1.0.
CHAPTER 5 : Ricoh eQuill Tablet Care 5.1 - Instructions for Care The Ricoh eQuill tablet is not waterproof. If your tablet does get wet, unplug all cables. Wait for the tablet to dry completely before powering it on. Do not attempt to dry your tablet with an external heat source, such as a hair dryer. Clean the screen with a soft cloth; be careful not to wipe it with anything abrasive. 5.2 - Camera Care 5.2.1 - Removing Dust and Dirt Use a microfiber lens cloth to remove dust and lint. Use light strokes.
CHAPTER 5 : Ricoh eQuill Tablet Care NOTE: Make sure the your tablet battery level is at least 20% to complete an update. A red LED light on the tablet indicates the battery level is too low. 2. An Update splash screen on the tablet will instruct you of actions to be performed, and will indicate that the tablet is updating (see ”Software Update Settings Page” on page 58). 3. The tablet will reboot when finished with the OTA update. The Update splash screen disappears after the tablet is updated.
CHAPTER 5 : Ricoh eQuill Tablet Care Page 44 Version 1.0.
C H APT E R 6 Settings Page ”Settings Page Overview” on page 46 ”Network Settings Page” on page 48 ”User Settings Page” on page 49 ”Tools Settings Page” on page 51 ”Software Update Settings Page” on page 58 ”About Settings Page” on page 59 Ricoh eQuill Tablet | Version 1.0.
CHAPTER 6 : Settings Page 6.1 - Settings Page Overview Tapping the Settings icon allows you to view tablet information and make modifications to the tablet via the Settings Page. The Settings Page has two sections: ”General Settings” on page 46 ”Other Settings” on page 47 Figure 6-1: Settings Page Home Screen See page 48 See page 49 See page 51 See page 58 See page 59 6.1.1 - General Settings The General section of the page contains the Airplane Mode, Sounds, and Volume settings.
CHAPTER 6 : Settings Page Use the Volume control to adjust the loudness of events that occur (e.g., pressing the Submit button, camera shutter button press, and so on). 6.1.
CHAPTER 6 : Settings Page 6.2 - Network Settings Page (Settings > Network) The Network Settings page displays Networks, Connection, and 3G information. Figure 6-2: Network Settings Page Wi-Fi The Magnifying Glass icon, when tapped, performs a scan of local networks. Network names are displayed in the box. Only known networks are displayed and recognized.
CHAPTER 6 : Settings Page NOTE: Not all networks may be found on the first scan. If needed, repeat the scan. Remember that if a network has a hidden SSID, it will not appear in the scan results. Connection This section contains the Wi-Fi address, 3G address, and other network information. As the system connects, you may see these fields changing. 3G Radio This section displays the 3G status of the tablet. The options are enabled or disabled. 6.
CHAPTER 6 : Settings Page The user information is taken from the provisioning process. The following user information is displayed on this page: ID, Name, Email, Account. Use the Logout button to log out of the user account. Page 50 Version 1.0.
CHAPTER 6 : Settings Page 6.4 - Tools Settings Page (Settings > Tools) The Tools Settings page provides access to the following tools: ”Stylus (Pen) Calibration” on page 51 ”Support Tools (3G)” on page 52 ”Customer Diagnostics” on page 55 Figure 6-4: Tools Settings Page See page 51 See page 52 See page 55 6.4.1 - Stylus (Pen) Calibration (Settings > Tools > Calibrate) Tap the Calibrate button for stylus calibration. See ”Step 3 — Calibrate” on page 24 for instructions.
CHAPTER 6 : Settings Page 6.4.2 - Support Tools (3G) (Settings > Tools > Open) Tap the Open button to access support tools (Figure 6-5) which are used to request updates of the 3G operating parameters. The parameters are updated Over-The-Air by the 3G service provider. Some of buttons available on this page require a password to be entered in order to proceed. The password is available from your technical support representative (1-855-Go-eWriter).
CHAPTER 6 : Settings Page Figure 6-5: Support Tools Page Modem Status Displays the present state of the 3G module (Idle, Ready, Connecting, Connected, KeepAlive, and Disconnecting). This is an active display and will be updated should the state change. Factory Reset This password protected button (Reset Now) will return the 3G module to the original factory settings. The module is powered off by the tablet after the reset is complete. At the next tablet Ricoh eQuill Tablet | Version 1.0.
CHAPTER 6 : Settings Page synchronization (sync) request, the tablet will automatically request a Device Configuration (DC) update. Manual DC Updates This is a password protected button (Update Now) which will request a management session with the service provider. Primarily this updates the Mobile Internet Protocol (MIP) profile. This profile must be set to one (1) in order to establish a PPP connection that has full internet access.
CHAPTER 6 : Settings Page Scheduled Update The tablet is configured to request updates at regular intervals. This display shows when the next update is scheduled. Update Status This button (Details) will open a dialog box which will display the current status of any updates which are in progress as well as the next scheduled update. NOTE: Do NOT power off the tablet or attempt to put the tablet to sleep while an update is in progress. 6.4.
CHAPTER 6 : Settings Page Figure 6-6: Diagnostic Tools Page Upload Logs Will create a compressed file of the Inbox, templates, system logs and other configuration information. Once the archive is created, an attempt is made to transfer the archive to the recovery directory of the POD. The creation and transfer can take more than ten (10) minutes. When the attempt to transfer is complete, a dialog box indicating success or failure will be presented.
CHAPTER 6 : Settings Page REBOOT Performs a reboot of the tablet software. The reboot will wait until the OK button is tapped, or you attempt to navigate away from the diagnostics page. 3G ON Will attempt to power on the 3G radio. If the network manager has not been stopped, that process will immediately power the radio off again. 3G OFF Will attempt to power off the 3G radio. If the network manager has not been stopped, that process will immediately power the radio on again.
CHAPTER 6 : Settings Page 6.5 - Software Update Settings Page (Settings > Software Update) This page displays the current software version and shows an Updates message. Figure 6-7: Software Settings Page SETTINGS Current Version: software is up to date. rootfs_1.0.2-3034-premaster-dev-msp-r-k-20120518T153027 rootfs_1.0.2-3034-premaster-dev-msp-r-k-20120518T153027 Your Ricoh eQuill software is up to date.
CHAPTER 6 : Settings Page Once the download is complete, the OTA icon will appear on your Inbox Page. Tap the OTA icon, which will bring you to the screen above. The progress bar will disappear and the Upgrade button will now become active. Tap the Upgrade button to complete the software upgrade on your tablet. You will first see a software update message (“Starting software update... please wait”), then you will a sequence of screens.
CHAPTER 6 : Settings Page Figure 6-8: About Settings Page Page 60 Version 1.0.
C H APT E R 7 Ricoh eQuill Tablet Specifications ”Ricoh eQuill Tablet Specifications” on page 62 ”Camera Operation” on page 63 ”Entering Data — Stylus and Keyboard” on page 63 Ricoh eQuill Tablet | Version 1.0.
CHAPTER 7 : Ricoh eQuill Tablet Specifications 7.1 - Ricoh eQuill Tablet Specifications Feature Feature Description Internal Storage 8 GB Display E Ink® Electronic Paper Display Picture Display 0.95” (24.13mm) OLED Display Size 246 mm (9.
CHAPTER 7 : Ricoh eQuill Tablet Specifications 7.2 - Camera Operation Operation Procedure How do you turn on the camera? If the camera has been enabled for a document, press and release the shutter button. That causes the camera to turn on and the camera display to start showing previews. Where does the photo go after you snap the shutter? It is displayed in gray scale, and placed onto the page. Some documents may be configured to add the photo as a separate page at the end of the document.
CHAPTER 7 : Ricoh eQuill Tablet Specifications with the stylus. You cannot use the stylus to draw in a field that has been defined by the administrator as a keyed entry field. The Ricoh eQuill offers the following text options: Uppercase Text Lowercase Text Punctuation Text Accent Mark Text 7.3.3 - Uppercase Text The uppercase text is invoked by pressing and releasing the shift key and then selecting a letter. It enters one uppercase letter before it reverts to lowercase. 7.3.
CHAPTER 7 : Ricoh eQuill Tablet Specifications 7.3.5 - Punctuation Keyboard The punctuation keyboard is invoked by tapping and holding the punctuation key . The lowercase keyboard is invoked from the punctuation keyboard by tapping the alphabet key . 7.3.6 - Accent Keys The accent keys are an additional set of keys that are revealed by pressing the relevant base character for one second. For example, the accented a characters are all revealed by pressing and holding the a key.
CHAPTER 7 : Ricoh eQuill Tablet Specifications Page 66 Version 1.0.
C H APT E R 8 Troubleshooting This chapter addresses problems that maybe encountered with the Ricoh eQuill tablet. ”General Issues” on page 67 ”Unresponsive Ricoh eQuill Tablet” on page 67 ”Unresponsive Charged Ricoh eQuill Tablet” on page 68 ”LED Lights Interpretation” on page 69 8.1 - General Issues Contact you administrator for the following issues: Documents not getting submitted Document shows an error Unable to connect to Wi-Fi or 3G Upgrading your software 8.
CHAPTER 8 : Troubleshooting 8.3 - Unresponsive Charged Ricoh eQuill Tablet You may need to do a hard reset. Contact Ricoh, or follow these instructions. Caution A reset may cause a loss of data that was not saved to the server. On the bottom of the tablet you will find a small hole. Gently insert a paper clip into the hole until you hear it click. Reset Hole When you have successfully reset your tablet, the LED indicator light will blink blue. The tablet will then start up as normal.
CHAPTER 8 : Troubleshooting 8.4 - LED Lights Interpretation LED On/Off Switch During normal use, the LEDs will only be used during large tasks, such as booting and shutting down. When in use, blinking LEDs indicate the tablet status. When off, you only get solid LEDs to indicate charging status. LED Light Description No lights Tablet is not charging; no external power. Red light blinking Tablet tried to perform an unsuccessful operation. See your administrator.
CHAPTER 8 : Troubleshooting Page 70 Version 1.0.
Index Index Numerics 3G module information 59 3G Radio network settings 49 A About Settings 59 Accent Keys 65 Accessories 33 Accessory Plug 21 removal for stylus holder 30 arrow icon 47 B Backward Page Flip Button 21 battery indicator 26 battery life 62 Battery Power states 27 Blank Forms opening 27 Blank Forms (templates) 22 C Calibration 24 Camera 22, 62 care 42 operation 63 turning on 63 Camera Display 21 CE Information 13 Charging Contact 21 communications protocols supported 62 Compliance 7 Connect
Index D Deleting a Document 27 Device Configuration update Diagnostics 3G OFF 57 3G ON 57 3G VPD 57 Daemon 56 IF CONFIG 56 NetMgr Start 56 NetMgr Stop 56 PING 56 PPP down 57 PPP UP 57 REBOOT 57 Upload Logs 56 Wi-Fi down 57 Wi-Fi up 57 Display 21 display color 62 size 62 type 62 document shows an error 67 documents not submitted 67 54 E E Ink Display 22 entering data 63 F Factory Reset 53 FCC compliance 11 First Use 22 flying wireless service 9 Forward Page Flip Button 21 FUMO modem firmware 54 G Gettin
Index H Hardware Version 54 I Icons Battery 24 Blank Forms 23 Delete 24 Inbox 23 OTA 24 Settings 24 Status Column 24 Sync Start 24 Sync status 24 Wireless/3G Signal 24 Inbox Documents 22 input device pen digitizer 62 K Keyboard 62, 63 L Layout 21 LED Indicator 21 LED Lights 27 LED Lights Interpretation Legal information 59 license information 59 Lowercase Text 64 69 M Manual DC Updates 54 Manual FUMO Update 54 Manual PRL Update 54 microphone 21, 62 MIP Profile 54 Modem Firmware 54 Modem Status 53 Mu
Index N Network Settings 48 O On/Off Switch 21 One-button Routing 22 Open a Document 25 operating temperature 62 OTA icon 24 Over-The-Air software download Software Update 42 58 P package contents 30 page buttons backwards and forwards 47 Page Flip Buttons 21 photo deletion 63 saving 63 sending to another Inbox 63 Power Connector 21 power indicator 26 PRL 54 Punctuation Text 65 Q Quick Start 20 R Radio Frequency (RF) Exposure regulatory information 59 reset tablet 68 12 S Safety 7 Scheduled Update
Index Sleep mode 26 Soft Keyboard 22 soft keyboard 63 Software Update OTA 42 Software Update Settings 58 Speaker 21 Specifications 62 status icons 24 Storage Requirements 42 Stylus 22, 30, 63 Calibration (pen) 51 holder 30 tether 30 Stylus Tether Cord 31 Submit Button 21 Submit button 25 Support Tools (3G) 52 sync (synchronize) function 28 T Tablet Care 41 tablet reset 68 Templates blank forms 22 Tether Cord 31 Tools Settings 51 Troubleshooting 67 Turning Off tablet 26 U unable to connect to Wi-Fi 67 Unre
Index Wi-Fi network settings wireless service when flying 9 wireless support 62 Page 76 48 Version 1.0.
