Specifications

Troubleshooting 5-9
M M L 0 0
E1D1 FNS LEAD JAM 2 Paper did not arrive at Paper Exit 2 PS. 5-22
E1D2 FNS LEAD JAM 3 Paper did not arrive at Stacker Conveyance Passage PS. 5-22
E1D3 FNS LEAD JAM 4 Paper did not arrive at Paper Exit 1 PS. 5-22
E1D5 FNS TRAIL JAM 2 Paper did not depart from Paper Exit 2 PS. 5-22
E1D6 FNS TRAIL JAM 3 Paper did not depart from Stacker Conveyance Passage PS. 5-22
E1D7 FNS TRAIL JAM 4 Paper did not depart from Paper Exit 1 PS. 5-22
E1D8 FNS LEAD JAM 5 Paper did not arrive at Sub-Tray Paper Exit PS. 5-22
E1D9 FNS TRAIL JAM 5 Paper did not depart from Sub-Tray Paper Exit PS. 5-22
E255 INSERTER PICK COUNT OVER The insert pick count is over 15 sheets. 5-26
E259 CONFIGURATION ERROR Finisher configuration is changed. 5-43
E260 FINISHER CPU ERROR Slave processor cannot receive the status data from the
Finisher processor.
5-26
E262 FINISHER INCORRECT
COMMAND
Finisher received the command when its condition prohibits
PR from issuing.
5-27
E264 FINISHER ACT TIMEOUT Finisher does not become an activate condition. 5-27
E266 FINISHER DORMANT TIMEOUT Finisher does not become a dormant condition. 5-27
E268 FINISHER BUSY TIMEOUT The Busy signal of the Finisher is on more than specified time. 5-27
E26A FINISHER ST EXIT SIGNAL
ERROR
The Stacker exit signal is on more than specified time. 5-27
E26C FINISHER PRINT TIMEOUT The Print signal of the Finisher is on more than specified time. 5-27
E2B1 FNS COVER SHEET TRAY
TIMEOUT
The table of the Cover Sheet Feeder is on more than the
specified time.
5-28
E2C1 STAPLER POSITION ERROR Abnormality was detected in the Staple Movement HP PS. 5-29
E2C2 STAPLING ERROR Both staplers missed to staple. 5-30
E2C3 STAPLING F ERROR Stapler (Front) missed to staple. 5-30
E2C4 STAPLING R ERROR Stapler (Rear) missed to staple. 5-30
E2C5 STAPLER ROTATE ERROR 1 Abnormality was detected in the Staple Rotation HP PS.
(slant)
5-31
E2C6 SHIFT TRAY TIMEOUT The Main Tray was driven too long time. 5-32
E2C7 ALIGNMENT PLATE POSITION
ERROR
Abnormality was detected in the Alignment Plate/Upper HP
PS.
5-33
E2C8 SHIFT POSITION ERROR Abnormality was detected in the Roller Shift HP PS. 5-34
E2C9 BELT POSITION ERROR Abnormality was detected in the Paper Exit Belt HP PS. 5-35
E2CA PAPER EXIT OPENING
POSITION ERROR
Abnormality was detected in the Paper Exit Opening PS. 5-36
E2CB STAPLER ROTATE ERROR 2 Abnormality was detected in the Stapler Rotation HP PS.
(parallel)
5-36
E2E5 FNS DRIVER Abnormality was detected in the Finisher driver. 5-37
E2E7 FNS CONVEYANCE MOTOR
ERROR
FNS Conveyance Motor did not work correctly. 5-37
E2E8 FOLDING CONVEYANCE MOTOR
ERROR
Folding Conveyance Motor did not work correctly. 5-37
Detail
Error
Code
Error Name Description
Page
No.