Operating instructions

ManualsBrandsRicoh ManualsComputer equipmentAficio MP 3500SP

Operating Instructions

General Settings Guide

Read this manual carefully before you use this machine and keep it handy for future reference. For safe and correct use, be sure to read the

Safety Information in "About This Machine" before using the machine.

Connecting the Machine

System Settings

Copier / Document Server Features

Facsimile Features

Printer Features

Scanner Features

Registering Addresses and Users for Facsimile/Scanner Functions

Other User Tools

Appendix

Downloaded From ManualsPrinter.com Manuals

Summary of content (331 pages)

PAGE 1
Operating Instructions General Settings Guide 1 Connecting the Machine 2 System Settings 3 Copier / Document Server Features 4 Facsimile Features 5 Printer Features 6 Scanner Features 7 Registering Addresses and Users for Facsimile/Scanner Functions 8 Other User Tools 9 Appendix Read this manual carefully before you use this machine and keep it handy for future reference. For safe and correct use, be sure to read the Safety Information in "About This Machine" before using the machine.
PAGE 2
Introduction This manual contains detailed instructions and notes on the operation and use of this machine. For your safety and benefit, read this manual carefully before using the machine. Keep this manual in a handy place for quick reference. Important Contents of this manual are subject to change without prior notice. In no event will the company be liable for direct, indirect, special, incidental, or consequential damages as a result of handling or operating the machine.
PAGE 3
Manuals for This Machine Refer to the manuals that are relevant to what you want to do with the machine. ❖ About This Machine Be sure to read the Safety Information in this manual before using the machine. This manual provides an introduction to the functions of the machine. It also explains the control panel, preparation procedures for using the machine, how to enter text, and how to install the CD-ROMs provided.
PAGE 4
❖ Other manuals • Quick Reference Copy Guide • Quick Reference Fax Guide • Quick Reference Printer Guide • Quick Reference Scanner Guide • PostScript3 Supplement • UNIX Supplement • Manuals for DeskTopBinder Lite • DeskTopBinder Lite Setup Guide • DeskTopBinder Introduction Guide • Auto Document Link Guide Note ❒ Manuals provided are specific to machine types. ❒ Adobe Acrobat Reader/Adobe Reader must be installed in order to view the manuals as PDF files.
PAGE 5
TABLE OF CONTENTS Manuals for This Machine ......................................................................................i How to Read This Manual .....................................................................................1 Symbols .....................................................................................................................1 Display Panel..........................................................................................................2 Accessing User Tools .
PAGE 6
3. Copier / Document Server Features General Features..................................................................................................91 Reproduction Ratio..............................................................................................96 Edit ......................................................................................................................100 Stamp ..............................................................................................................
PAGE 7
Special Senders to Treat Differently ................................................................161 Authorized Reception.............................................................................................162 Reception File Print Quantity .................................................................................163 Forwarding .............................................................................................................163 Print 2 Sided......................................
PAGE 8
7. Registering Addresses and Users for Facsimile/Scanner Functions Address Book..................................................................................................... 207 Managing names in the Address Book ..................................................................210 Sending fax by Quick Dial ......................................................................................210 Sending e-mail by Quick Dial .............................................................................
PAGE 9
8. Other User Tools Maintenance ....................................................................................................... 277 Changing the Display Language ...................................................................... 278 Enquiry................................................................................................................ 279 Counter ...............................................................................................................
PAGE 10
viii Downloaded From ManualsPrinter.
PAGE 11
How to Read This Manual Symbols This manual uses the following symbols: Indicates important safety notes. Ignoring these notes could result in serious injury or death. Be sure to read these notes. They can be found in the "Safety Information" section of About This Machine. Indicates important safety notes. Ignoring these notes could result in moderate or minor injury, or damage to the machine or to property. Be sure to read these notes.
PAGE 12
Display Panel The display panel shows machine status, error messages, and function menus. The function items displayed serve as selector keys. You can select or specify an item by lightly pressing them. When you select or specify an item on the display panel, it is highlighted like . Keys appearing as cannot be used. Important ❒ A force or impact of more than 30 N (about 3 kgf) will damage the display panel.
PAGE 13
Accessing User Tools User Tools allow you to change or set defaults. Note ❒ Operations for system settings differ from normal operations. Always quit User Tools when you have finished. ❒ Any changes you make with User Tools remain in effect even if the main power switch or operation switch is turned off, or the {Energy Saver} or {Clear Modes} key is pressed. ❒ Default settings are shown in bold type. Reference p.
PAGE 14
C Select the user tool you want to change. D Change settings by following instructions on the display, and then press [OK]. Note ❒ To cancel changes made to settings and return to the initial display, press the {User Tools/Counter} key. Reference p.47 “System Settings” p.91 “Copier / Document Server Features” p.123 “Facsimile Features” p.187 “Printer Features” p.201 “Scanner Features” p.277 “Other User Tools” Quitting User Tools This section describes how to end User Tools.
PAGE 15
1. Connecting the Machine This chapter describes how to connect the machine to the network and specify the network settings. Connecting to the Interfaces This section explains how to identify the machine’s interface and connect the machine according to the network environment. AQT002S 1. IEEE 1394 ports (optional) 5. Wireless LAN port (optional) Ports for connecting the IEEE 1394 interface cable Port for using the wireless LAN 2. USB2.0 port Port for connecting the USB2.0 interface cable 3.
PAGE 16
Connecting the Machine Connecting to the Ethernet Interface Connect 10BASE-T or 100BASE-TX cable to the Ethernet interface. 1 Important ❒ If the main power switch is on, turn it off. A A ferrite core for the Ethernet cable is supplied with this machine. Make a loop in the cable about 3cm (1.2 inch) (1) from the machine end of the cable. Attach the ferrite core. AEV047S B Make sure the main power switch of the machine is off. C Connect the Ethernet interface cable to the 10BASE-T/100BASE-TX port.
PAGE 17
Connecting to the Interfaces E Turn on the main power switch of the machine. 1 AME005S A B Indicator (green) Lights up green when the machine is connected correctly to the network. Indicator (yellow) Lights up yellow when 100 BASE-TX is in operation. Goes off when 10 BASE-T is in operation. Note ❒ For details about installing the printer driver, see "Preparing the Machine", Printer Reference.
PAGE 18
Connecting the Machine Connecting to the USB Interface Connect the USB2.0 interface cable to the USB2.0 port. 1 A Connect the USB2.0 interface cable to the USB2.0 port. AQS014S B Connect the other end to the USB2.0 port on the host computer. Note ❒ This machine does not come with a USB interface cable. Make sure you purchase the appropriate cable for the machine and your computer. ❒ The USB2.0 interface board is supported by Windows Me / 2000 / XP, Windows Server 2003, Mac OS X 10.3.3 or higher.
PAGE 19
Connecting to the Interfaces Connecting to the IEEE 1394 Interface Connect the IEEE 1394 interface cable to the IEEE 1394 interface board. A Connect the IEEE 1394 interface cable to the IEEE 1394 port. 1 AQS016S B Connect the other end of the cable into the interface connector on the host computer. Check the shape of the connector to the computer. Connect the cable firmly. Note ❒ Use the interface cable supplied with the IEEE 1394 interface board.
PAGE 20
Connecting the Machine Connecting to the IEEE 1284 Interface Connect the IEEE 1284 interface cable to the IEEE 1284 interface board. 1 A Make sure the main power switch on the machine is off. B Turn off the main power switch of the host computer. C Connect the IEEE 1284 interface cable to the IEEE 1284 port. AQS017S Use the conversion connector (1) supplied with the IEEE 1284 interface board. D Connect the other end of the cable into the interface connector on the host computer.
PAGE 21
Connecting to the Interfaces Connecting to the IEEE 802.11b (Wireless LAN) Interface Connect to the IEEE 802.11b (wireless LAN) interface. 1 Note ❒ Check the settings of the IPv4 address and subnet mask of this machine. ❒ For details about how to set the IPv4 address and subnet mask from the control panel of the machine, see "Interface Settings". Reference p.59 “Network” Setup Procedure Set up IEEE 802.11b (wireless LAN) according to the following procedure: AME006S Downloaded From ManualsPrinter.
PAGE 22
Connecting the Machine 1 Note ❒ Select [802.11 Ad-hoc Mode] mode when connecting Windows XP as a wireless LAN client using Windows XP standard driver or utilities, or when not using the infrastructure mode. ❒ You can specify either "WEP" or "WPA" to the Security Method. ❒ Specify "WPA", when [Communication Mode] is set to [Infrastructure Mode]. ❒ For details about how to specify wireless LAN settings from the control panel on the machine, see "IEEE 802.11b".
PAGE 23
Connecting to the Interfaces ❖ When using in adhoc mode / 802.11 ad hoc mode 1 1 2 ZGDH600J 1. If the IEEE 802.11b interface unit is functioning, the LED lights up in orange. 2. If it is connected properly to the network, the LED is green when in ad hoc mode or 802.11 ad hoc mode. If the LED is blinking, the machine is searching for devices. The LED will light after a few seconds. Print the configuration page to verify settings.
PAGE 24
Connecting the Machine Network Settings 1 This section describes the network settings you can change with User Tools (System Settings). Make settings according to functions you want to use and the interface to be connected. Important ❒ These settings should be made by the system administrator, or with the advice of the system administrator. Settings Required to Use the Printer/LAN-Fax This section lists the settings required for using the printer or LAN-Fax function.
PAGE 25
Network Settings Menu Interface Settings/Network User Tool Machine Name Setting Requirements As required Note ❒ IPv6 can be used only for the printer function. 1 ❒ For the Effective Protocol setting, check that the protocol you want to use is set to [Active]. ❒ [LAN Type] is displayed when the wireless LAN board is installed. If Ethernet and IEEE 802.11b (wireless LAN) are both connected, the selected interface has priority. Reference p.
PAGE 26
Connecting the Machine IEEE 802.11b (wireless LAN) 1 This section lists the settings required for using the printer or LAN-Fax function with an IEEE 802.11b (wireless LAN) connection. For details about how to specify the settings, see "Interface Settings".
PAGE 27
Network Settings Note ❒ For the Effective Protocol setting, check that the protocol you want to use is set to [Active]. ❒ [IEEE 802.11b] and [LAN Type] are displayed when the wireless LAN interface board is installed. If both Ethernet and wireless LAN (IEEE 802.11b) are connected, the selected interface takes precedence. 1 Reference p.59 “Interface Settings” Settings Required to Use Internet Fax This section lists the settings required for using Internet Fax.
PAGE 28
Connecting the Machine Menu 1 User Tool Setting Requirements File Transfer E-mail Reception Interval As required File Transfer Max. Reception E-mail Size As required File Transfer E-mail Storage in Server As required File Transfer Program / Change / Delete E-mail Message As required File Transfer Fax E-mail Account Necessary Note ❒ For the Effective Protocol setting, check that the protocol you want to use is set to [Active].
PAGE 29
Network Settings Menu User Tool Setting Requirements Interface Settings/Network IPv4 Gateway Address Necessary Interface Settings/Network DNS Configuration Interface Settings/Network Effective Protocol Necessary File Transfer SMTP Server Necessary File Transfer SMTP Authentication As required File Transfer POP before SMTP As required File Transfer Reception Protocol As required File Transfer POP3 / IMAP4 Settings As required File Transfer Administrator's E-mail Address As require
PAGE 30
Connecting the Machine IEEE 802.11b (wireless LAN) 1 This section lists the settings required for using Internet Fax with an IEEE 802.11b (wireless LAN) connection. For details about how to specify the settings, see "Interface Settings" and "File Transfer".
PAGE 31
Network Settings Menu User Tool File Transfer Program / Change / Delete E-mail Message File Transfer Fax E-mail Account Setting Requirements As required Necessary 1 Note ❒ For the Effective Protocol setting, check that the protocol you want to use is set to [Active]. ❒ [IEEE 802.11b] and [LAN Type] are displayed when the wireless LAN interface board is installed. If both Ethernet and wireless LAN (IEEE 802.11b) are connected, the selected interface takes precedence.
PAGE 32
Connecting the Machine Menu 1 User Tool Setting Requirements Interface Settings/Network WINS Configuration As required Interface Settings/Network Effective Protocol Interface Settings/Network Ethernet Speed Interface Settings/Network LAN Type Interface Settings/Network Permit SNMPv3 Communication As required Interface Settings/Network Permit SSL/TLS Communication As required Interface Settings/Network Host Name As required File Transfer SMTP Server File Transfer SMTP Authentication
PAGE 33
Network Settings IEEE 1394 (IPv4 over 1394) This section lists the settings required for sending e-mail with an IEEE 1394 connection. For details about how to specify the settings, see "Interface Settings" and "File Transfer".
PAGE 34
Connecting the Machine IEEE 802.11b (wireless LAN) 1 This section lists the settings required for sending e-mail with an IEEE 802.11b (wireless LAN) connection. For details about how to specify the settings, see "Interface Settings" and "File Transfer".
PAGE 35
Network Settings Note ❒ For the Effective Protocol setting, check that the protocol you want to use is set to [Active]. ❒ [LAN Type] is displayed when the wireless LAN interface board is installed. If both Ethernet and wireless LAN (IEEE 802.11b) are connected, the selected interface takes precedence. ❒ When POP before SMTP is set to [On], you must also make settings for Reception Protocol and POP3 / IMAP4 Settings.
PAGE 36
Connecting the Machine Note ❒ For the Effective Protocol setting, check that the protocol you want to use is set to [Active]. 1 ❒ [LAN Type] is displayed when the wireless LAN interface board is installed. If both Ethernet and wireless LAN (IEEE 802.11b) are connected, the selected interface takes precedence. Reference p.59 “Interface Settings” p.69 “File Transfer” IEEE 1394 (IPv4 over 1394) This section lists the settings required for sending files with an IEEE 1394 connection.
PAGE 37
Network Settings IEEE 802.11b (wireless LAN) This section lists the settings required for sending files with an IEEE 802.11b (wireless LAN) connection. For details about how to specify the settings, see "Interface Settings" and "File Transfer".
PAGE 38
Connecting the Machine Settings Required to Use the Network Delivery Scanner This section lists the settings required for delivering data to network. 1 Ethernet This section lists the settings required for delivering data to network with an Ethernet connection. For details about how to specify the settings, see "Interface Settings" and "File Transfer".
PAGE 39
Network Settings IEEE 1394 (IPv4 over 1394) This section lists the settings required for delivering data to network with an IEEE 1394 connection. For details about how to specify the settings, see "Interface Settings" and "File Transfer".
PAGE 40
Connecting the Machine IEEE 802.11b (wireless LAN) 1 This section lists the settings required for delivering data to network with an IEEE 802.11b (wireless LAN) connection. For details about how to specify the settings, see "Interface Settings" and "File Transfer".
PAGE 41
Network Settings Reference p.59 “Interface Settings” p.69 “File Transfer” 1 Settings Required to Use Network TWAIN Scanner This section lists the settings required for using TWAIN Scanner under the network environment. Ethernet This section lists the settings required for using network TWAIN Scanner with an Ethernet connection. For details about how to specify the settings, see "Interface Settings".
PAGE 42
Connecting the Machine IEEE 1394 (IPv4 over 1394) 1 This section lists the settings required for using network TWAIN Scanner with an IEEE 1394 connection. For details about how to specify the settings, see "Interface Settings" and "File Transfer".
PAGE 43
Network Settings IEEE 802.11b (wireless LAN) This section lists the settings required for using network TWAIN Scanner with an IEEE 802.11b (wireless LAN) connection. For details about how to specify the settings, see "Interface Settings".
PAGE 44
Connecting the Machine Settings Required to Use Document Server 1 This section lists the settings required for using Document Server function under the network environment. Ethernet This section lists the settings required for using Document Server function with an Ethernet connection. For details about how to specify the settings, see "Interface Settings".
PAGE 45
Network Settings IEEE 1394 (IPv4 over 1394) This section lists the settings required for using Document Server function with an IEEE 1394 connection. For details about how to specify the settings, see "Interface Settings".
PAGE 46
Connecting the Machine IEEE 802.11b (wireless LAN) 1 This section lists the settings required for using Document Server function with an IEEE 802.11b (wireless LAN) connection. For details about how to specify the settings, see "Interface Settings".
PAGE 47
Network Settings Using Utilities to Make Network Settings You can also specify network settings using utilities such as Web Image Monitor, SmartDeviceMonitor for Admin, and telnet. 1 Note ❒ For details about using Web Image Monitor, see "Using Web Image Monitor", Network Guide. ❒ For details about using SmartDeviceMonitor for Admin, see "Using SmartDeviceMonitor for Admin", Network Guide. ❒ For Details about using telnet, see "Remote Maintenance", Network Guide.
PAGE 48
Connecting the Machine 1 ❖ [Network] → [Machine IPv6 Address] → [Manual Configuration Address] • Web Image Monitor: Can be used for specifying the setting. • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting. • telnet: Can be used for specifying the setting. ❖ [Network] → [IPv6 Stateless Address Autoconfiguration] • Web Image Monitor: Can be used for specifying the setting. • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
PAGE 49
Network Settings ❖ [Network] → [WINS Configuration] → [On] → [Secondary WINS Server] • Web Image Monitor: Can be used for specifying the setting. • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting. • telnet: Can be used for specifying the setting. 1 ❖ [Network] → [WINS Configuration] → [On] → [Scope ID] • Web Image Monitor: Can be used for specifying the setting. • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting.
PAGE 50
Connecting the Machine 1 ❖ [Network] → [NW Frame Type] → [Auto Select] • Web Image Monitor: Can be used for specifying the setting. • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting. • telnet: Can be used for specifying the setting. ❖ [Network] → [NW Frame Type] → [Ethernet II] • Web Image Monitor: Can be used for specifying the setting. • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting. • telnet: Can be used for specifying the setting.
PAGE 51
Network Settings ❖ [Network] → [LAN Type] → [Ethernet] • Web Image Monitor: Can be used for specifying the setting. • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting. • telnet: Can be used for specifying the setting. 1 ❖ [Network] → [LAN Type] → [IEEE 802.11b] • Web Image Monitor: Can be used for specifying the setting. • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting. • telnet: Can be used for specifying the setting.
PAGE 52
Connecting the Machine 1 ❖ [IEEE 1394] → [IPv4 over 1394] • Web Image Monitor: Can be used for specifying the setting. • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting. • telnet: Can be used for specifying the setting. ❖ [IEEE 1394] → [WINS Configuration] → [On] → [Primary WINS Server] • Web Image Monitor: Can be used for specifying the setting. • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting. • telnet: Can be used for specifying the setting.
PAGE 53
Network Settings ❖ [IEEE 802.11b] → [Channel] • Web Image Monitor: Can be used for specifying the setting. • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting. • telnet: Can be used for specifying the setting. 1 ❖ [IEEE 802.11b] → [Security Method] • Web Image Monitor: Can be used for specifying the setting. • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting. • telnet: Can be used for specifying the setting. ❖ [IEEE 802.
PAGE 54
Connecting the Machine 1 ❖ [File Transfer] → [Administrator's E-mail Address] • Web Image Monitor: Can be used for specifying the setting. • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting. • telnet: Cannot be used for specifying the setting. ❖ [File Transfer] → [E-mail Communication Port] • Web Image Monitor: Can be used for specifying the setting. • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting. • telnet: Cannot be used for specifying the setting.
PAGE 55
Network Settings ❖ [File Transfer] → [Number of Scanner Resends] • Web Image Monitor: Cannot be used for specifying the setting. • SmartDeviceMonitor for Admin: Cannot be used for specifying the setting. • telnet: Cannot be used for specifying the setting. Downloaded From ManualsPrinter.
PAGE 56
Connecting the Machine Connecting the Machine to a Telephone Line and Telephone 1 This section describes how to connect the machine to the telephone lines and select the line type. Connecting the Telephone Line To connect the machine to a telephone line, use a snap-in modular type connector. Important ❒ Make sure the connector is the correct type before you start. AQT003S 1. External telephone connector 2. G3 interface unit connector 3.
PAGE 57
2. System Settings This chapter describes user tools in the System Settings menu. For details on how to access System Settings, see "Accessing User tools (System Settings)". General Features This section describes the user tools in the General Features menu under System Settings. Default settings are shown in bold type. ❖ Program / Change / Delete User Text You can register text phrases you often use when specifying settings, such as ".com" and "Regards". You can register up to 40 entries.
PAGE 58
System Settings ❖ Warm-Up Beeper (copier/Document Server) You can have the beeper sound when the machine becomes ready to copy after leaving Energy Saver mode, or when the power is turned on. • On • Off 2 ❖ Copy Count Display (copier/Document Server) The copy counter can be set to show the number of copies made (count up) or the number of copies yet to be made (count down).
PAGE 59
General Features ❖ Output: Copier (copier) Specify a tray to which documents are delivered. 2 AQT004S 1. Finisher Upper Tray 2. Finisher Shift Tray 3. Finisher Upper Tray 4. Finisher Shift Tray 5. Finisher Upper Tray 6. Finisher Shift Tray 7. Finisher Booklet Tray 8. Internal Tray 1 9. Internal Tray 2 ❖ Output: Document Server (Document Server) Specify a tray to which documents are delivered.
PAGE 60
System Settings 2 ❖ Output: Printer (printer) Specify a tray to which documents are delivered. The output trays set on the printer driver have priority over the output tray specified below. • Internal Tray 1 • Internal Tray 2 • Finisher Upper Tray • Finisher Shift Tray ❖ System Status/Job List Display Time Specify how long to display the System Status and Job List display for. • On: 60 second(s) • Off By selecting [On], you can specify a display time between 10 and 999 seconds.
PAGE 61
Tray Paper Settings Tray Paper Settings This section describes the user tools in the Tray Paper Settings menu under System Settings. Default settings are shown in bold type. Important ❒ If the specified paper size differs from the actual size of the paper loaded in the paper tray, a misfeed might occur because the correct paper size was not detected. 2 ❖ Paper Tray Priority: Copier (copier/Document Server) Specify the tray to supply paper for output.
PAGE 62
System Settings ❖ Tray Paper Size: Tray 2-4 Select the size of the paper loaded in the paper tray. The paper guide for the optional LCT is fixed for A4K, 81/2"×11"K size paper. Contact your service representative if you need to change the paper size.
PAGE 63
Tray Paper Settings ❖ Printer Bypass Paper Size Specify the size of the paper in the bypass tray when printing data from the computer.
PAGE 64
System Settings 2 • Paper Thickness • Thin Paper • Plain Paper (60-81g/m2, 16-22lb.) • Middle Thick (82-105g/m2, 22-28lb.) • Thick Paper 1 (106-169g/m2, 28.5-44.9lb.) • Thick Paper 2 (170-219g/m2, 45-58lb.) • Thick Paper 3 (220-253g/m2, 58.5-67lb.) ❖ Paper Type: Tray 1-4 Sets the display so you can see what type of paper is loaded in each paper tray. The print function uses this information to automatically select the paper tray.
PAGE 65
Tray Paper Settings ❖ Cover Sheet Tray Allows you to specify and display the paper tray that is setting cover sheets. After selecting the paper tray, you can also specify the display timing and copy method for two-sided copying.
PAGE 66
System Settings Note ❒ When paper of the same type and size is loaded in two different paper trays and you want to specify tray for 2 Sided Copy and tray for 1 Sided Copy, specify the upper tray for 2 Sided Copy. If one of the trays is specified as the default in Paper Tray Priority, assign 2 Sided Copy to that tray. 2 ❒ A mark appears next to the paper tray if [Off] is selected in [Auto Paper Select].
PAGE 67
Timer Settings Timer Settings This section describes the user tools in the Timer Settings menu under System Settings. Default settings are shown in bold type. ❖ Auto Off Timer After a specified period has passed, following job completion, the machine automatically turns off, in order to conserve energy. This function is called "Auto Off". The machine status after the Auto Off operation is referred to as "Off mode", or "Sleep mode". For the Auto Off Timer, specify the time to elapse before Auto Off.
PAGE 68
System Settings ❖ Facsimile Auto Reset Timer (facsimile) Specifies the time to elapse before the facsimile mode resets. The time can be set from 30 to 999 seconds, using the number keys. The default setting is 30 second(s). 2 ❖ Printer Auto Reset Timer (printer) Specifies the time to elapse before the printer function resets. • On • Off The time can be set from 10 to 999 seconds, using the number keys. The default setting is 60 second(s).
PAGE 69
Interface Settings Interface Settings This section describes the user tools in the Interface Settings menu under System Settings. Default settings are shown in bold type. 2 Network This section describes the user tools in the Network menu under Interface Settings. ❖ Machine IPv4 Address Before using this machine in the network environment, you must specify the IPv4 address and subnet mask. When you select [Specify], enter the IPv4 address and subnet mask as "xxx.xxx.xxx.xxx" ("x" indicates a number).
PAGE 70
System Settings ❖ IPv6 Gateway Address Displays the machine’s IPv6 gateway address. ❖ IPv6 Stateless Address Autoconfiguration Specify IPv6 Stateless Address Autoconfiguration. • Active • Inactive 2 ❖ DNS Configuration Make settings for the DNS server. When you select [Specify], enter the DNS Server IPv4 address as "xxx.xxx.xxx.xxx"("x" indicates a number). • Auto-Obtain (DHCP) • Specify • DNS Server 1: 000.000.000.000 • DNS Server 2: 000.000.000.000 • DNS Server 3: 000.000.000.
PAGE 71
Interface Settings ❖ Effective Protocol Select the protocol to use in the network. • IPv4: Active / Inactive • IPv6: Active / Inactive • NetWare: Active / Inactive • SMB: Active / Inactive • AppleTalk: Active / Inactive 2 ❖ NCP Delivery Protocol Select the protocol for NCP delivery. • IPX Priority • TCP / IP Priority • IPX Only • TCP / IP Only If you select "IPX Only" or "TCP / IP Only", you cannot switch the protocol even if you cannot connect with it.
PAGE 72
System Settings 2 ❖ Ethernet Speed Set the access speed for networks. Select a speed that matches your network environment. [Auto Select] should usually be selected. • Auto Select • 10Mbps Full Duplex • 10Mbps Half Duplex • 100Mbps Full Duplex • 10Mbps Half Duplex ❖ LAN Type When you have installed the IEEE 802.11b interface unit, select the method of connection. • Ethernet • IEEE 802.11b [LAN Type] is displayed when wireless LAN board is installed. If Ethernet and IEEE 802.
PAGE 73
Interface Settings ❖ Host Name Specify the host name. Enter the host name using up to 63 characters. ❖ Machine Name Specify the machine name. Enter the machine name using up to 31 characters. 2 Parallel Interface This section describes the user tools in the Parallel Interface menu under Interface Settings. [Parallel Interface] is displayed when this machine is installed with the IEEE 1284 interface board. ❖ Parallel Timing Sets the timing for the control signal of the parallel interface.
PAGE 74
System Settings ❖ Signal Control Specifies how error during printing or sending facsimile from the computer is to be dealt with. • Job Acceptance Priority • Printer Priority 2 IEEE 1394 This section describes the user tools in the IEEE 1394 menu under Interface Settings. [IEEE 1394] is displayed when this machine is installed with the IEEE 1394 interface board. ❖ IPv4 Address Before using this machine in the network environment, you must specify the IPv4 address and subnet mask.
PAGE 75
Interface Settings ❖ WINS Configuration Specify the WINS server settings. If [On] is selected, specify the WINS Server IPv4 address as "xxx.xxx.xxx.xxx" ("xxx" indicates a number). If DHCP is in use, specify the scope ID. Enter scope ID using up to 31 characters. • On • Primary WINS Server: 000.000.000.000 • Secondary WINS Server: 000.000.000.
PAGE 76
System Settings IEEE 802.11b 2 This section describes the user tools in the IEEE 802.11b menu under Interface Settings. [IEEE 802.11b] is displayed when this machine is installed with the wireless LAN interface board. Be sure to make all settings simultaneously. ❖ Communication Mode Specifies the communication mode of the wireless LAN. • 802.11 Ad-hoc Mode • Ad-hoc Mode • Infrastructure Mode ❖ SSID Setting Specifies SSID to distinguish the access point in infrastructure mode or 802.11 ad hoc mode.
PAGE 77
Interface Settings ❖ Wireless LAN Signal When using in infrastructure mode, you can check the machine's radio wave status using the control panel. Radio wave status is displayed when you press [Wireless LAN Signal]. ❖ Transmission Speed Specifies the communication speed of the IEEE 802.11b (wireless LAN). • Auto Select • 11Mbps Fixed • 5.5Mbps Fixed • 2Mbps Fixed • 1Mbps Fixed 2 ❖ Restore Factory Defaults You can return the IEEE 802.11b (wireless LAN) settings to their defaults. • No • Yes Reference p.
PAGE 78
System Settings B Press [Interface Settings]. 2 C Press [Print List]. D Press the {Start} key. The configuration page is printed. E Press [Exit]. F Press the {User Tools/Counter} key. Note ❒ You can also exit by pressing [Exit] on the User Tools main menu. 68 Downloaded From ManualsPrinter.
PAGE 79
File Transfer File Transfer This section describes the user tools in the File Transfer menu under System Settings. Default settings are shown in bold type. ❖ Delivery Option Enables or disables sending stored or scanned documents to the ScanRouter delivery server. • On • Main Delivery Server IPv4 Address • Sub Delivery Server IPv4 Address • Off Specify this option when selecting whether or not to use the ScanRouter delivery software.
PAGE 80
System Settings 2 • File to Deliver Specify whether all received fax documents or only received fax documents that include delivery codes (ID or SUB/SEP codes) are sent to the ScanRouter delivery software. • File with Delivery Code • Print File • Delivery Failure File If a received fax document cannot be sent to the ScanRouter delivery software, it is stored in memory. To print a stored file, select [Print File], to delete, select [Delete File].
PAGE 81
File Transfer ❖ SMTP Authentication Specify SMTP authentication (PLAIN, LOGIN, CRAMMD5, DIGEST-MD5). When sending e-mail to an SMTP server, you can enhance the SMTP server security level using authentication that requires entering the user name and password. If the SMTP server requires authentication, set [SMTP Authentication] to [On], and then specify the user name, password and encryption. Enter the user name and password to be set for the Administrator's e-mail address when using Internet Fax.
PAGE 82
System Settings ❖ Reception Protocol Specify Reception Protocol for receiving Internet Fax. • POP3 • IMAP4 • SMTP 2 ❖ POP3 / IMAP4 Settings Specify the POP3/IMAP4 server name for receiving Internet faxes. The specified POP3/IMAP4 server name is used for [POP before SMTP]. • Server Name If DNS is in use, enter the host name. If DNS is not in use, enter the POP3/IMAP4 or server IPv4 address. Enter POP3/IMAP4 server name using up to 127 characters. Spaces cannot be entered.
PAGE 83
File Transfer ❖ E-mail Communication Port Specify the port numbers for receiving Internet faxes. The specified POP3 port number is used for [POP before SMTP]. • POP3: 110 • IMAP4: 143 • SMTP: 25 Enter a port number between 1 and 65535 using the number keys, and then press the {q} key. 2 ❖ E-mail Reception Interval Specify, in minutes, the time interval for receiving Internet faxes via POP3 or IMAP4 server.
PAGE 84
System Settings 2 ❖ Program / Change / Delete E-mail Message You can program, change, or delete the e-mail message used when sending an Internet fax or scan file as an attachment. Program / Change: A Press [System Settings]. B Press [File Transfer]. C Press [TNext]. D Press [Program / Change / Delete E-mail Message]. E Press [Program / Change]. F Press [Not Programmed]. G Press [Change]. H Enter a name, and then press [OK]. Enter the name using up to 20 characters. I Press [Edit].
PAGE 85
File Transfer ❖ Auto Specify Sender Name Set whether or not to specify the name of the sender when sending e-mail. • On If you select [On], the specified e-mail address will appear in the "From:" box. If you do not specify the sender’s address, the administrator’s e-mail address will appear in the "From:" box.
PAGE 86
System Settings Administrator Tools 2 This section describes the user tools in the Administrator Tools menu under System Settings. Default settings are shown in bold type. Administrator Tools are used by the administrator. To change these settings, contact the administrator. We recommend specifying Administrator Authentication before making Administrator Tools settings. ❖ Address Book Management You can add, change or delete information registered in the Address Book. For details, see "Address Book".
PAGE 87
Administrator Tools ❖ Address Book: Program / Change / Delete Group Names registered in the Address Book can be added into a group. You can then easily manage the names registered in each group. • Program / Change You can register and change groups. • Names You can register a name, key display, registration number, and title selection. • Programmed User/Group You can check the names or groups registered in each group. • Protection You can register a protection code.
PAGE 88
System Settings D Press the name key to be moved. E You can select a name using the number keys. Press the name key in the place you want to move it to. 2 The user key is moved to the selected position, and the user key currently at the selected position is moved forward or backward. If you move the selected user key forward, the user key currently at the selected position is moved backward. If you move the selected user key backward, the user key currently at the selected position is moved forward.
PAGE 89
Administrator Tools ❖ Print Address Book: Destination List You can print the destination list registered in the Address Book. • Print in Title 1 Order Prints the Address Book in Title 1 order. • Print in Title 2 Order Prints the Address Book in Title 2 order. • Print in Title 3 Order Prints the Address Book in Title 3 order. • Print Group Dial List Prints the group Address Book. A Press [System Settings]. B Press [Administrator Tools]. C Press [Print Address Book: Destination List].
PAGE 90
System Settings E F 2 Enter the new name, and then press [OK]. Press [OK]. ❖ Address Book: Switch Title Specifies the title to select a name. • Title 1 • Title 2 • Title 3 ❖ Back Up / Restore Address Book You can back up the machine’s address book to external storage or restore the backup copy from the external storage. • Back Up You can back up the machine’s address book to external storage. • Restore You can restore the backup copy of the address book from external storage.
PAGE 91
Administrator Tools ❖ User Authentication Management • User Code Auth. Using User Code Authentication, you can limit the available functions and supervise their use. When using User Code Authentication, register the user code. Using the Printer PC Control function, you can obtain a log of prints corresponding to the codes entered using the printer driver. If User Code Authentication has been specified, Auto Colour Select cannot be used.
PAGE 92
System Settings 2 ❖ Auto Delete File in Document Server Specify whether documents stored in the Document Server will or will not be deleted after a specified period of time. • On: 3 day(s) • Off If you select [On], documents stored subsequently are deleted after the specified period. If you select [Off], documents are not automatically deleted. If you select [On], enter a number of days from 1 to 180 (in 1 day increments).
PAGE 93
Administrator Tools To use the LDAP server in Administrator Tools, select [On] under LDAP server. This function supports LDAP Version 2.0 and 3.0. Ver 2.0 does not support High Security authentication. ❖ LDAP Search Specify whether or not to use the LDAP server for searching. • On • Off If you select [Off], LDAP server list will not appear on the searching display. 2 ❖ AOF (Always On) Specify whether or not to use Auto Off.
PAGE 94
System Settings Program / Change / Delete LDAP Server This section explains how to specify the LDAP server settings. To program / change the LDAP server 2 A Press [System Settings]. B Press [Administrator Tools]. C Press [Program / Change / Delete LDAP Server]. D Check that [Program / Change] is selected. E Select the LDAP server you want to program or change. When programming the server, select [Not Programmed]. F Set each item as necessary. G Press [OK] after setting each item.
PAGE 95
Administrator Tools Programming the LDAP server This section explains how to specify the LDAP server settings. To enter an identification name A Press [Change] under "Name". 2 Register a name for the LDAP server that will appear on the server selection screen of the LDAP search operation. B Enter the server’s identification name. C Press [OK]. To enter a server name A Press [Change] under "Server Name". Register the LDAP server’s host name or IPv4 address. B Enter the LDAP server name. C Press [OK].
PAGE 96
System Settings To enter a port number A Press [Change] under "Port No.". Specify the port number for communicating with the LDAP server. Specify a port that is compliant with your environment. 2 B Enter the port number using the number keys, and then press the {#} key. When SSL is set to [On], the port number automatically changes to "636". To start SSL communication A Press [On] under "Use Secure Connection (SSL). Use SSL to communicate with the LDAP server.
PAGE 97
Administrator Tools To enter the user name and password A Press [TNext]. B Press [Change] under "User Name". When [On] or [High Security] is selected for the authentication setting, use the administrator account name and password. Do not enter the administrator account name and password when using authentication for each individual or each search. 2 C Enter the user name, and then press [OK]. Procedures for the user name setting differ depending on server environment.
PAGE 98
System Settings To set search conditions A Press [TNext] twice. B Press [Change] for items you want to use as search conditions from the fol- 2 lowing: [Name], [E-mail Address], [Fax Number], [Company Name], and [Department Name]. You can enter an attribute as a typical search keyword. Using the entered attribute, the function searches the LDAP server’s Address Book. C Enter the attribute you want to use when searching for e-mail addresses, and then press [OK].
PAGE 99
Administrator Tools E Enter the key display, and then press [OK]. The registered "key display" appears as a keyword for searching LDAP. • Without key display registration 2 • With key display registration The key does not appear on the search screen unless both "Attribute" and "Key Display" are registered. Make sure you register both to use the optional search. Downloaded From ManualsPrinter.
PAGE 100
System Settings 2 90 Downloaded From ManualsPrinter.
PAGE 101
3. Copier / Document Server Features This chapter describes user tools in the Copier / Document Server Features menu. For details on how to access Copier / Document Server Features, see "Accessing User Tools (System Settings)". General Features This section describes the user tools in the General Features menu under Copier / Document Server Features. Default settings are shown in bold type.
PAGE 102
Copier / Document Server Features ❖ Original Photo Type Priority When you select "Text / Photo" or "Photo" in "Original Type Priority", you can change the settings of the selected original type. • Glossy Photo • Printed Photo • Copied Photo 3 ❖ Original Type Display You can have the original types shown on the initial display. • Hide • Display If you select [Hide], the display is as below. ❖ Paper Display You can choose to have the available paper trays and sizes shown on the initial display.
PAGE 103
General Features ❖ Copy Orientation in Duplex Mode You can set the copy orientation when making two-sided copies. • Top to Top • Top to Bottom ❖ Max. Copy Quantity The maximum copy quantity can be set between 1 and 999. The default setting is 999 sheets. ❖ Auto Tray Switching If you load paper of the same size in two or more trays, the machine automatically shifts to the other when the first tray runs out of paper (when Auto Paper Select is selected.) This function is called "Auto Tray Switching".
PAGE 104
Copier / Document Server Features ❖ Customize Function: Copier You can assign up to six frequently-used functions to Copy Function keys.
PAGE 105
General Features • Rotate Sort • Positive/Negative ❖ Customize Function: Document Server Storage You can assign up to six frequently-used functions to Document Server Storage keys.
PAGE 106
Copier / Document Server Features Reproduction Ratio This section describes the user tools in the Reproduction Ratio menu under Copier / Document Server Features. Default settings are shown in bold type. 3 ❖ Shortcut R/E You can register up to three frequently used Reduce / Enlarge ratios other than the fixed Reduce / Enlarge ratio and have them shown on the initial display. You can also change registered Reduce/ Enlarge ratios.
PAGE 107
Reproduction Ratio • Inch version • 25% • 11"×17" → 51/2"×81/2" (50%) • 11"×17" → 81/2"×11" (65%) • 11"×15" → 81/2"×11" (73%) • 81/2"×14" → 81/2"×11" (78%) • 81/2"×13" → 81/2"×11" (85%) • 93% • 81/2"×14" → 11"×17" (121%) • 81/2"×11" → 11"×17" (129%) • 51/2"×81/2" → 81/2"×14" (155%) • 51/2"×81/2" → 11"×17" (200%) • 400% • User R / E Ratio (25-400%) • Off Default: • F1: 73% • F2: 155% • F3: 93% 3 ❖ R / E Ratio Specify the enlargement and reduction ratios that appear if [Reduce / Enlarge] is pressed on the
PAGE 108
Copier / Document Server Features 3 • Metric version • 25% • A3 → A5, 8"×13" → A5 (50%) • A3 → 8"×13" (65%) • A3 → A4, A4 → A5 (71%) • B4JIS → 8"×13" (75%) • 8"×13" → A4, B4JIS → 8"×13" (82%) • 93% • B4JIS → A3 (115%) • 8"×13" → A3, A4 → B4JIS (122%) • A4 → A3, A5 → A4 (141%) • A5 → A3 (200%) • 400% • User R / E Ratio (25-400%) • Inch version • 25% • 11"×17" → 51/2"×81/2" (50%) • 11"×17" → 81/2"×11" (65%) • 11"×15" → 81/2"×11" (73%) • 81/2"×14" → 81/2"×11" (78%) • 81/2"×13" → 81/2"×11" (85%) • 93% • 81/2"
PAGE 109
Reproduction Ratio ❖ R/E Ratio Priority You can set the ratio that has priority when [Reduce / Enlarge] is pressed.
PAGE 110
Copier / Document Server Features Edit 3 This section describes the user tools in the Edit menu under Copier / Document Server Features. Default settings are shown in bold type. Enter the width of the binding margin with the number keys as follows: • Metric version: 0–30 mm (in increments of 1 mm) • Inch version: 0"-1.2" (in increments of 0.1 inch) Enter the width of the erased margin with the number keys as follows: • Metric version: 2–99 mm (in increments of 1 mm) • Inch version: 0.1"-3.
PAGE 111
Edit ❖ Back Margin: Top/Bottom Specify top and bottom margins on the back side of copies in Margin Adjustment mode. • Top • Bottom Default: • Metric version: T / B: 0mm • Inch version: T / B: 0.0" ❖ 1 Sided → 2 Sided Auto Margin: TtoT In 1 sided to 2 sided Duplex mode, you can specify the margins on the back side. The margin is set to the same value of "Back Margin: Left/Right". • Left • Right Default: • Metric version: Right 5 mm • Inch version: Right 0.
PAGE 112
Copier / Document Server Features ❖ Erase Centre Width Specify the width of the erased centre margins with this function. Default: • Metric version: 10 mm • Inch version: 0.4" ❖ Front Cover Copy in Combine You can make a combined copy on the front cover sheet when you select Front Cover mode. 3 GCST019E • Combine • Do not Combine ❖ Copy Order in Combine You can set the copy order in Combine mode to Left to Right or Top to Bottom.
PAGE 113
Edit ❖ Image Repeat Separation Line You can select a separation line and colour using the Image Repeat function from: None, Solid, Broken A, Broken B, or Crop Marks. • None • Solid 3 • Broken A • Broken B • Crop Marks Line colour (Full Colour): • Yellow • Red • Cyan • Magenta • Green • Blue • Black Separation lines cannot be specified when using [None]. In "Black and White", printing will be done in black. Selecting solid or broken lines might produce a blank area of approximately 1.5 mm (0.
PAGE 114
Copier / Document Server Features ❖ Double Copies Separation Line You can select a separation line using the Double Copies function from: None, Solid, Broken A, Broken B, or Crop Marks. • None • Solid 3 • Broken A • Broken B • Crop Marks Line colour (Full Colour): • Yellow • Red • Cyan • Magenta • Green • Blue • Black Separation lines cannot be specified when using [None]. In "Black and White", printing will be done in black.
PAGE 115
Edit ❖ Separation Line in Combine You can select a separation line using the Combine function from: None, Solid, Broken A, Broken B, or Crop Marks. • None • Solid 3 • Broken A • Broken B • Crop Marks Line colour (Full Colour): • Yellow • Red • Cyan • Magenta • Green • Blue • Black Separation lines cannot be specified when using [None]. In "Black and White", printing will be done in black. Selecting solid or broken lines might produce a blank area of approximately 1.5 mm (0.
PAGE 116
Copier / Document Server Features Stamp This section describes the user tools in the Stamp menu under Copier / Document Server Features. Default settings are shown in bold type. Background Numbering 3 This section describes the user tools in the Background Numbering menu under Stamp. ❖ Size You can set the size of the numbers. • Small • Normal • Large ❖ Density You can set the density of the numbers. • Light • Normal • Dark • Very Dark ❖ Stamp Colour You can set the colour of the numbers.
PAGE 117
Stamp Preset Stamp This section describes the user tools in the Preset Stamp menu under Stamp. ❖ Stamp Language You can select the language of the message printed in Stamp mode. • English • German • French • Italian • Spanish • Dutch • Portuguese • Polish • Czech • Swedish • Finnish • Hungarian • Norwegian • Danish • Russian • Japanese • Simplified Chinese • Traditional Chinese • Hangul 3 ❖ Stamp Priority You can select the stamp type given priority when [Preset Stamp] is pressed.
PAGE 118
Copier / Document Server Features 3 ❖ Stamp Format Specify how each of stamp is printed. • Stamp Position Specify where to print the stamp. • Top Left • Top Centre • Top Right • Centre Left • Centre • Centre Right • Bottom Left • Bottom Centre • Bottom Right • Stamp Position You can adjust the position of the stamp within the available ranges shown below.
PAGE 119
Stamp • Density You can set the pattern used to print the stamp. • Normal The stamp is printed on the image. You cannot check which parts will overlap. • Lighter The image can be seen through the stamp. • Lightest The image appears even clearer than in the Lighter setting. • Page to Stamp You can have the stamp printed on the first page or all pages. • All Pages • 1st Page Only 3 ❖ Stamp Colour Sets the stamp print colour.
PAGE 120
Copier / Document Server Features User Stamp This section describes the user tools in the User Stamp menu under Stamp. ❖ Program/Delete Stamp You can register, change, or delete user stamps. You can register up to four custom stamps with your favorite designs. 3 ❖ Stamp Format:1-4 Specify how each of registered User Stamps 1 to 4 is printed. • Stamp Position Specify where to print the User Stamp.
PAGE 121
Stamp • Page to Stamp Sets whether to print the stamp on all pages or only the first page. • All Pages • 1st Page Only ❖ Stamp Colour:1-4 Sets the colour registered in User Stamp colour (1 to 4). • Yellow • Red • Cyan • Magenta • Green • Blue • Black 3 Reference "User Stamp", Copy/Document Server Reference Date Stamp This section describes the user tools in the Date Stamp menu under Stamp. ❖ Format You can select the date format for Date Stamp mode. • MM / DD / YYYY • MM.DD.YYYY • DD / MM / YYYY • DD.
PAGE 122
Copier / Document Server Features ❖ Size You can set the Date Stamp size. • Auto • Large • Middle • Small 3 ❖ Superimpose You can have the Date Stamp printed in white when it overlaps black parts of the image. • On • Off ❖ Stamp Colour You can set the selected priority colour when printing the date. • Yellow • Red • Cyan • Magenta • Green • Blue • Black 112 From ManualsPrinter.
PAGE 123
Stamp ❖ Stamp Setting Specify how Date Stamp is printed. • Stamp Position Specify where to print the Date Stamp. • Top Left • Top Centre • Top Right • Bottom Left • Bottom Centre • Bottom Right • Stamp Position You can adjust the position of the Date Stamp within the available ranges shown below.
PAGE 124
Copier / Document Server Features Page Numbering This section describes the user tools in the Page Numbering menu under Stamp. 3 ❖ Stamp Format You can select the page number format given priority when [Page Numbering] is pressed. • P1,P2… • 1/5,2/5… • -1-,-2-… • P.1,P.2… • 1,2… • 1-1,1-2… ❖ Font You can select the page number printed in Page Numbering mode. • Font 1 • Font 2 • Font 3 ❖ Size You can set the size of the stamp printed in Page Numbering mode.
PAGE 125
Stamp ❖ Stamp Position Specify how each of stamp is printed. • Stamp Position Specify where to print the stamp. • Top Left • Top Centre • Top Right • Bottom Left • Bottom Centre • Bottom Right • Stamp Position You can adjust the position of the stamp within the available ranges shown below.
PAGE 126
Copier / Document Server Features ❖ Page Numbering Initial Letter You can select the page numbering initial letter between "P1, P2.../P.1, P.2..." and "S1, S2.../S.1, S.2...". • P1, P2.../P.1, P.2... • S1, S2.../S.1, S.2... Reference p.3 “Accessing User Tools” 3 116 From ManualsPrinter.
PAGE 127
Input/Output Input/Output This section describes the user tools in the Input/Output menu under Copier / Document Server Features. Default settings are shown in bold type. ❖ Switch to Batch You can select to have Batch mode or SADF mode displayed when you press the [Special Original] key. • Batch • SADF 3 ❖ SADF Auto Reset In SADF mode, an original must be set within a specified time after the previous original has been fed. You can adjust this time from 3 to 99 seconds in increments of 1 second.
PAGE 128
Copier / Document Server Features 3 ❖ Staple Position Specify which Top 2 staples or Bottom shown on the initial display with priority. The optional 1000-sheet finisher, 3000-sheet finisher, or booklet finisher is required to use this function. • Top 1 • Centre • Left 2 • Top 2 • Bottom 1 • Slant • Off ❖ Punch Type Specify which punch type (2 holes or 3 holes) has priority to be shown on the initial display.
PAGE 129
Input/Output ❖ Simplified Screen: Finishing Types You can select which key is displayed with higher priority for "Finishing Types" on the Simplified Screen. • Stack • Slant • Top 1 • Bottom 1 • Left 2 • 2 Holes Left • 3 Holes Left • 4 Holes Left • Do not Display 3 Reference p.3 “Accessing User Tools” "Orientation-Fixed Paper or Two-Sided Paper", Troubleshooting "Batch mode", Copy/ Document Server Reference "Sort", Copy/ Document Server Reference Downloaded From ManualsPrinter.
PAGE 130
Copier / Document Server Features Adjust Colour Image This section describes the user tools in the Adjust Colour Image menu under Copier / Document Server Features. Default settings are shown in bold type. 3 ❖ Background Density of ADS (Full Colour) "The background density is adjusted to skip the texture and copy. You can adjust the background density up to 5 levels when in Full Colour. Centre of the 5 level adjustment is set by default.
PAGE 131
Settings for the Document Server Settings for the Document Server For details, see "System Settings", and "Copier / Document Server Features".
PAGE 132
Copier / Document Server Features 3 122 From ManualsPrinter.
PAGE 133
4. Facsimile Features This chapter describes user tools in the Facsimile Features menu. For details on how to access Facsimile Features, see "Accessing User Tools (System Settings)". General Features This section describes the user tools in the General Features menu under Facsimile Features. ❖ Quick Operation Key (1-3) Frequently used functions programmed as Quick Operation keys are shown on the menu immediately after the power is turned on.
PAGE 134
Facsimile Features Up to three functions can be programmed to Quick Operation keys. Functions that appear dimmed have already been set. ❖ Switch Title Select the title to be shown on the destination list. • Title 1 • Title 2 • Title 3 ❖ Search Destination Select a destination list to be used in "Search Destination". You can select from Address Book, or registered LDAP Server. 4 ❖ Communication Page Count Checks the transmission, reception, and totals on the display.
PAGE 135
General Features ❖ On Hook Mode Release Time Use this function to specify a time to cancel On Hook mode after you transmit using On Hook dialing. • 1 minute • 3 minutes • 5 minutes • 10 minutes Reference p.3 “Accessing User Tools” p.174 “Box Settings” "Adjusting the Volume", Troubleshooting "Sending at a Specific Time (Send Later)", Facsimile Reference "Fax Header Print", Facsimile Reference "Reading the Display", Facsimile Reference Downloaded From ManualsPrinter.
PAGE 136
Facsimile Features Scan Settings This section describes the user tools in the Scan Settings menu under Facsimile Features. ❖ Program / Change / Delete Scan Size You can program, change, or cancel frequently used scan sizes. For details about programming Scan Size, see "Program / Change / Delete Scan Size". Reference p.3 “Accessing User Tools” p.143 “Program / Change / Delete Scan Size” 4 126 From ManualsPrinter.
PAGE 137
Send Settings Send Settings This section describes the user tools in the Send Settings menu under Facsimile Features. ❖ Max. E-mail Size When the other party has a limit on the size of e-mail messages that can be received, or sending data heavy e-mail causes problems, you can make settings to limit the size of sent e-mail. When this function is set to on, transmission of e-mail that exceeds the set size is aborted.
PAGE 138
Facsimile Features ❖ Program / Change / Delete Standard Message Program standard messages to be printed at the top of the first page of the original of the opposite party. It is useful for personalizing messages such as sending greetings. You can program three standard messages. You cannot change the "Confidential", "Urgent", "Please phone.", or "Copy to corres. section" messages. The procedure is the same for both programming and changing. A Press [Facsimile Features]. B Press [Send Settings].
PAGE 139
Send Settings ❖ Backup File TX Setting You can specify whether or not to send to a selected folder the backup of a file sent by Memory Transmission. By setting [Backup File TX Setting] to [On] and selecting the destination folder, you can automatically send to the selected folder the backup of a file sent by Memory Transmission using the machine’s control panel, Web Image Monitor, DeskTopBinder, or LAN-Fax. Select the destination folder for the backup file from the address book.
PAGE 140
Facsimile Features Reception Settings This section describes the user tools in the Reception Settings menu under Facsimile Features. ❖ Switch Reception Mode Specify the method for receiving fax documents. • Manual Reception • Auto Reception 4 ❖ Program Special Sender By programming particular receivers as Special Sender in advance, you can have Special Senders treated differently. For details about how to program Special Sender, see "Special Senders to Treat Differently".
PAGE 141
Reception Settings ❖ Stored Reception File User Setting The administrator can be specified for managing documents stored on the machine after fax documents are received. To specify the administrator, enter the administrator user code for managing documents using Web Image Monitor or DeskTopBinder. You must register the administrator's User Code to the destination list in advance. This function is only available when [Store] is selected in "Reception File Setting".
PAGE 142
Facsimile Features A Press [On]. B Press [Change], and then enter the sending e-mail address to be authorized. C If you make a mistake, press [Backspace] or [Clear], and then enter again. Press [OK] twice. 4 ❖ 2 Sided Print Specify whether or not received fax documents are to be printed on both sides of the paper. • On • Off ❖ Checkered Mark Specify whether or not a checkered mark is to be printed on the first page of received fax documents.
PAGE 143
Reception Settings ❖ Print Reception Time Specify whether or not the received date, time, and file number are printed at the bottom of received fax documents. • On • Off ❖ Reception File Print Quantity Specify the number of copies to be printed for each fax document received. • 1 to 10 set(s) ❖ Paper Tray Use this function to print fax documents received from programmed senders and fax documents from other senders, using different paper trays.
PAGE 144
Facsimile Features 4 E Select the line type. F Select a tray to deliver the received paper onto, and then press [OK]. If you want to specify another line type, repeat from step 5. ❖ Folder Transfer Result Report You can set whether the Folder Transfer Result Report is transmitted to the specified e-mail address, when folders are programmed as the forwarding destinations to which documents are sent from all senders or Special Senders.
PAGE 145
Reception Settings ❖ Memory Lock Reception When you switch Memory Lock on, received documents are stored in memory and not printed automatically. When a document is received in the Memory Lock mode, the Confidential File indicator blinks. To print this document, enter the Memory Lock ID. A user without the ID cannot print the document. This prevents unauthorized users from accessing the document. To use Memory Lock, program the Memory Lock ID, and then switch Memory Lock on.
PAGE 146
Facsimile Features Initial Settings This section describes the user tools in the Initial Settings menu under Facsimile Features. ❖ Parameter Setting User Parameters allow you to customize various settings to suit your needs. For details about Parameter Setting, see "Parameter Settings". 4 ❖ Parameter Setting: Print List You can print Parameter Setting list. Print this list to see the current User Parameter settings. However, not all the parameter settings are printed. A Press [Facsimile Features].
PAGE 147
Initial Settings ❖ Program Memory Lock ID Program a Memory Lock ID to be entered before printing documents when the Memory Lock function is activated. A Press [Facsimile Features]. B Press [Initial Settings]. C Press [Program Memory Lock ID]. D Enter an ID using the number keys, and then press [OK]. A Memory Lock ID can be any four-digit number, except 0000. 4 E If you make a mistake, press [Clear] or the {Clear/Stop} key before pressing [OK], and then try again. Press the {User Tools/Counter} key.
PAGE 148
Facsimile Features ❖ Program Fax Information Program information to be shown on the display of the other machine and printed as a report. The following information can be programmed. • Fax Header • Own Name • Own Fax Number For details about how to program Fax Information, see "Registering Fax Information". 4 ❖ Enable H.323 Specify whether or not H.323 is used for IP-Fax transmission. • On • Off ❖ Enable SIP Specify whether or not SIP is used for IP-Fax transmission. • On • Off ❖ H.
PAGE 149
Initial Settings ❖ SIP Settings Set the SIP server's IPv4 address or host name, and SIP user name. If you select [On] using the User Parameters, you can use the SIP server. See "Parameter Settings" ( switch 34, bit 1). You can use alphanumeric symbols (lower and upper cases) and symbols (";", "?", ":", "&", "=", "+", "$", ",", "-", "_", ".", "!", "~", "*", "#", "‘", "(", ")", "%", "/", and "@") for registration of the SIP User Name in SIP Settings. Make sure you enter these characters correctly.
PAGE 150
Facsimile Features F G H Press [Change] for "Prefix". Enter the Prefix using the number keys, and then press [OK]. To change the existing prefix, press [Clear], and then enter a new prefix. For documents sent using a gateway to G3 Fax, prefixes can be used. If the first several digits of IP-Fax number and the gateway- specific prefix are identical, documents can be transmitted using the registered digits of the gateway.
PAGE 151
Reception File Setting Reception File Setting Specify whether received documents are to be saved on the hard disk or printed immediately without being saved. You can print stored documents repeatedly or download them as images to a computer using a Web Image Monitor or DeskTopBinder. If you select printing without saving, documents are printed each time they are received.
PAGE 152
Facsimile Features E Press the {User Tools/Counter} key. Note ❒ You can use "Parameter Settings" (switch 10, bit 5) to select whether or not to print stored received documents. See "Parameter Settings". 4 ❒ If [Store] is selected and a destination for notification is specified, notification of document reception can be sent to the specified e-mail address. ❒ Documents saved on the hard disk are categorized as received and stored documents.
PAGE 153
Program / Change / Delete Scan Size Program / Change / Delete Scan Size Program frequently used scan sizes. Important ❒ When programming or changing a scan size, it is recommended that you make a record of the new size. When you select a scan size to scan a custom size original, two custom sizes are available (Program Size 1 and Program Size 2). Use these functions to program a custom size in advance. The procedure is the same for programming and changing. You can program up to two sizes.
PAGE 154
Facsimile Features E Enter a horizontal size using the number keys. 4 Each time you press [mm] or [inch], the units switch between "mm" and "inch". If you enter a length and press [mm] or [inch], the length is converted automatically according to the unit (fractions are rounded off). For example, when you enter {2}, {2}, and {0} in millimeters and change to "inch", the length "8.7 inch" is shown on the display. If you press [mm] or [inch] again, "221 mm" is displayed.
PAGE 155
Program / Change / Delete Scan Size Deleting a scan size Delete programmed scan size. A Press [Facsimile Features]. B Press [Scan Settings]. C Press [Program / Change / Delete Scan Size]. D Press [Delete], and then select [Program Size 1] or [Program Size 2]. 4 E Press [Delete]. To cancel deleting, press [Do not Delete]. The display returns to that of stepD. F Press [Exit]. G Press the {User Tools/Counter} key. Downloaded From ManualsPrinter.
PAGE 156
Facsimile Features Registering Fax Information You can send information to the other party when transmitting or receiving a fax document. This information is shown on the display of the other machine and printed as a report. The following information can be sent. Important ❒ You can confirm programmed settings from the User Parameter List. It is recommended that you print and keep the User Parameter List when you program or change settings. See "Parameter List".
PAGE 157
Registering Fax Information Registering Fax Information A Press [Facsimile Features]. B Press [Initial Settings]. C Press [Program Fax Information]. D Select the Fax Information you want to register or change. 4 E Register the name and facsimile number. F Press [Exit]. G Press the {User tools/Counter} key. Registering a Fax Header A Check that [Fax Header] is selected. B Press [First Name] or [Second Name]. C Enter a fax header including your Own Name and Fax Number, and then press [OK].
PAGE 158
Facsimile Features Registering an Own Name A Press [Own Name]. B Press [Own Name]. 4 C Enter your own name, and then press [OK]. Registering an Own Fax Number A Press [Own Fax Number]. B Select line type to program. The display differs depending on the optional units installed on the machine. C Enter your own facsimile's number using the number keys, and then press [OK]. To enter a + sign or a space, press [+] or [Space]. 148 From ManualsPrinter.
PAGE 159
Registering Fax Information Changing Fax Information A Press [Facsimile Features]. B Press [Initial Settings]. C Press [Program Fax Information]. D Select the Fax Information you want to change. To change a Fax Header, see "Registering a Fax Header". To change Own Name, see "Registering an Own Name". To change Own Fax Number, "Registering an Own Fax Number". E Press [Exit]. F Press the {User tools/Counter} key. 4 Reference p.147 “Registering a Fax Header” p.148 “Registering an Own Name” p.
PAGE 160
Facsimile Features Forwarding Print documents received and forward to a specified End Receiver. This is useful if, for example, you are visiting another office and would like a copy of your documents to be sent to that office. You can also specify a "folder" as the forwarding destination. Important ❒ To use this function, set Forwarding under Reception Settings to On (enable). 4 ❒ You can select end receivers only from among destinations programmed in the Address Book.
PAGE 161
Forwarding Programming an End Receiver Important ❒ One end receiver can be registered for each special sender. To register two or more end receivers, use group destination. However, a maximum of 500 destinations can be specified in a group. A Press [Facsimile Features]. B Press [Reception Settings]. C Press [Forwarding]. D Press [On]. 4 If there is an End Receiver already programmed, a receiver name is shown. If you want to change the receiver, press [Receiver] and proceed to stepE.
PAGE 162
Facsimile Features E Specify an End Receiver using the destination list, and then press [OK]. 4 The receiver name is shown to the right of [Receiver]. Press the key on the left of the display to switch the destination between fax number, e-mail address, IP-Fax destination, and folder. Set a folder destination in Address Book Management under Administrator Tools in the System Settings menu. See "Registering Folders".
PAGE 163
Forwarding Quitting the forwarding function A Press [Facsimile Features]. B Press [Reception Settings]. C Press [Forwarding]. D Press [Off], and then press [OK]. 4 E Press the {User Tools/Counter} key. Forwarding Mark You can print a Forwarding Mark on receiver's documents that have been forwarded. The receiver can distinguish between forwarded and normally received documents. This function is not available when memory forwarding is performed to a folder destination. Reference p.
PAGE 164
Facsimile Features Parameter Settings User Parameters allow you to customize various settings to suit your needs. To change function settings, set the User Parameter Switches. ❖ Switches and Bits Each User Parameter has a set of switches, and each of the switches consist of eight bits, whose values are "0" or "1". The right most bit is bit 0 and the left most is bit 7. You can adjust the settings to match your needs by switching the value of bits between "0" and "1".
PAGE 165
Parameter Settings Switch Bit Item 0 1 05 Substitute the reception when the machine cannot print (because paper is jammed, all paper trays have run out of paper, toner is empty, or all paper trays are out of order) 00: Enabled unconditionally (Free) - 2,1 01: Enabled when Own Name/ Own Fax Number is received 10: Enabled for Closed Network Code match 4 11: Disabled (Reception off) 05 5 Print sheet is limited to that which has high- Off est priority.
PAGE 166
Facsimile Features Switch Bit Item 0 1 15 Selecting the available paper feed tray. 001: Tray 1 - 0, 1, 2 010: Tray 2 011: Tray 3 100: Tray 4 101: Large Capacity Tray (LCT) 4 15 5 Whether or not to select the available paper feed tray. 17 2 Whether you need to press [Add] after speci- Not fying a destination with the Destination key necessary when broadcasting Necessary 17 3 Whether or not to reset the settings when original is scanned.
PAGE 167
Parameter Settings Switch Bit Item 0 1 20 Reprinting time of stored documents in memory that could not be printed using LAN-Fax Driver 0000: 0 minutes - 5,4,3,2 0001: 1 minutes 0010: 2 minutes 0011: 3 minutes 0100: 4 minutes 0101: 5 minutes 0110: 6 minutes 4 0111: 7 minutes 1000: 8 minutes 1001: 9 minutes 1010: 10 minutes 1011: 11 minutes 1100: 12 minutes 1101: 13 minutes 1110: 14 minutes 1111: 15 minutes 21 0 Print results of sending Reception Notice Re- Off On quest message (print only when a
PAGE 168
Facsimile Features 4 Switch Bit Item 0 1 22 0 Detect a dial tone before sending faxes when using the telephone line (LINE) Not detect (Off) Detect (On) 22 1 Detect a dial tone before sending faxes when using the telephone line (LINE2) Not detect (Off) Detect (On) 22 2 Detect a dial tone before sending faxes when using the telephone line (LINE3) Not detect (Off) Detect (On) 24 0 Store documents that could not be transmitted in memory Off On 24 1 Length of time documents that could
PAGE 169
Parameter Settings Switch Bit Item 0 36 Maximum number of redials when sending a backup file 00000000: 7, 6, 5, 4, 3, 2, 1, 0 1 1 time(s) 00000001: 2 time(s) 00000010: 3 time(s) . . 11000000: 195 time(s) . .
PAGE 170
Facsimile Features Changing the User Parameters This section describes how to set parameters. Important ❒ Access to some User Parameter Settings may require options, or other settings may need to be made beforehand. ❒ It is recommended that you print and keep a User Parameter list when you program or change a User Parameter. ❒ Do not change any bit switches other than those shown on the previous pages. 4 A Press [Facsimile Features]. B Press [Initial Settings]. C Press [Parameter Setting].
PAGE 171
Special Senders to Treat Differently Special Senders to Treat Differently By programming particular senders in advance, you can set the following function for each sender: • Authorized RX • Forwarding • Reception File Print Qty • Print 2 Sided • Memory Lock • Paper Tray Use Own Name or Own Fax Number to program your senders. If the sender has a machine of the same manufacturer, program an Own Name that has already been programmed as a sender.
PAGE 172
Facsimile Features You can program up to 30 wild cards. Spaces are ignored when identifications are compared. You can use wild cards for the following functions: • Forwarding • Special Senders • Authorized RX (Authorized Reception) When using Partial agreement, you can enter up to the first 24 characters of an e-mail address to use it as an own name or facsimile name. Note ❒ You cannot program senders as Special Senders if they do not have Own Name or Own Fax Number programmed.
PAGE 173
Special Senders to Treat Differently Reference p.154 “Parameter Settings” Facsimile Reference "Reception Settings" Reception File Print Quantity Print the specified number of copies of documents received from programmed senders (Special Senders). If you do not program any Special Senders, the machine prints the specified number of copies for all received documents. Note ❒ You cannot use multi-copy printing with Memory Lock. ❒ You can specify up to 10 copies.
PAGE 174
Facsimile Features Print 2 Sided Print on both sides of the paper. Note ❒ If you select the bypass tray for "Paper Tray", duplex printing is disabled. Memory Lock 4 Store incoming documents from programmed senders (Special Senders) in memory without printing them. People without the Memory Lock ID cannot print the documents, and therefore this function is useful for receiving confidential documents .
PAGE 175
Special Senders to Treat Differently Programming/Changing Special Senders Program and change Special Senders. A Press [Facsimile Features]. B Press [Reception Settings]. C Press [Program Special Sender]. D Check [Program / Change] is selected. E Select the sender to program or change. 4 F Enter a sender name, and then press [OK]. Enter a destination name using Own Name or Own Fax Number. G Press [Full Agreement] or [Partial Agreement]. Downloaded From ManualsPrinter.
PAGE 176
Facsimile Features H Select the item you want to program. 4 You must select only the item you want to program. To cancel these settings, press [Cancel]. The display returns to that of stepE. I Press [OK]. A Special Sender is programmed. To program another sender, repeat the procedure from stepE. J Press [Exit]. K Press the {User Tools/Counter} key. Reference p.167 “Authorized RX (Authorized Reception)” p.168 “Forwarding” p.167 “Reception File Print Qty” p.169 “Print 2 Sided” p.169 “Memory Lock” p.
PAGE 177
Special Senders to Treat Differently Authorized RX (Authorized Reception) Specify when programming a Special Sender. A Press [Authorized Reception per Sender]. B Press [On] or [Off], and then press [OK]. 4 Reception File Print Qty Specify when programming a Special Sender. A Press [RX File Print Quantity per Sender]. B Press [Number of Sets]. C Enter the print quantity using the number keys, and then press [OK].
PAGE 178
Facsimile Features Forwarding Specify when programming a Special Sender. Important ❒ One forward destination can be registered for each Special Sender. To register two or more forward destinations, use group destinations. However a maximum of 500 destinations can be specified in a group. A Press [Forwarding per Sender]. B Select [On] or [Off]. If you select [Off], proceed to stepD. 4 C Press the Destination key of a forward destination, and then press [OK]. D Press [OK].
PAGE 179
Special Senders to Treat Differently Print 2 Sided Specify when programming a Special Sender. A Press [2 Sided Print per Sender]. B Press [On] or [Off], and then press [OK]. Note ❒ Selecting [Same as Basic Settings] will result in the same setting made for "2 Sided Print" of "Reception Settings". Memory Lock 4 Specify when programming a Special Sender. A Press [Memory Lock Reception per Sender]. B Press [On] or [Off], and then press [OK].
PAGE 180
Facsimile Features Programming Initial Set Up of a Special Sender Program the "Initial Set Up" of a Special Sender. You can also specify the Bypass Tray Paper Size. A Press [Facsimile Features]. B Press [Reception Settings]. C Press [Program Special Sender]. D Press [Initial Set Up]. 4 E Select the function you want to program. In this feature, "Authorized RX" has the same settings as "Reception Settings".
PAGE 181
Special Senders to Treat Differently G Press [On] or [Off], and then press [OK]. The illustration shows the "Authorized RX" display as an example. H To program Bypass Tray Paper Size, press [Bypass Tray Paper Size]. 4 You can select a size from [Auto Detect], [Regular Size], or [Custom Size]. If you select [Auto Detect], proceed to stepsI and N. If you select [Regular Size], proceed to stepsI, J and N. If you select [Custom Size], proceed to stepsI and K to N. I Select the size you want to program.
PAGE 182
Facsimile Features L Enter the vertical size of the paper using the number keys, and then press the {q} key. 4 Specify a vertical size from 90 mm (3.6") to 305 mm 12.0"). You cannot enter a size smaller than 90 mm or larger than 305 mm. Each time you press [mm] or [inch], the units switch between "mm" and "inch". If you enter a length and change the units by pressing [mm] or [inch], it is converted automatically (fractions are rounded off).
PAGE 183
Special Senders to Treat Differently Deleting a Special Sender Use this function to delete "Initial Set Up" of a Special Sender. The Bypass Tray Paper Size can also be deleted. A Press [Facsimile Features]. B Press [Reception Settings]. C Press [Program Special Sender]. D Press [Delete], and then select the Special Sender you want to delete. E Press [Yes]. 4 To cancel deleting a special sender, press [No]. The display returns to that of stepD. F Press [Exit]. G Press the {User Tools/Counter} key.
PAGE 184
Facsimile Features Box Settings The following functions are for delivery and transfer of documents: • Personal Box • Information Box • Transfer Box 4 ❖ SUB Code and SEP Code SUB Code and SEP Code are IDs consisting of up to 20 digits, and can include numbers, #, *, and spaces. To use this function, you must program a box and SUB/SEP Code beforehand. The other party can send documents to, and retrieve stored documents from, this box using the code.
PAGE 185
Box Settings E Select a box to program. When programming a new box, press [Not Programmed]. To change a box already programmed, press it and proceed to stepH. 4 F Press [Personal Box]. G Enter a box name, and then press [OK]. H Enter a SUB Code. To change the SUB Code, press [Clear] or the {Clear/Stop} key, and then try again. To change a Box name, press [Box Name], and then repeat from step G. I Specify the settings you require. If you do not want to program a password or receiver, proceed to stepP.
PAGE 186
Facsimile Features K Enter a password, and then press [OK]. If you make a mistake, press [Clear] or the {Clear/Stop} key before pressing [OK], and then try again. 4 L Re-enter the password, and then press [OK]. If you make a mistake, press [Clear] or the {Clear/Stop} key before pressing [OK], and then try again. To change the password after pressing [OK], press [Change] and repeat stepsK and L, or press [Cancel] and repeat from stepJ. M Press [OK]. N Press [Receiver].
PAGE 187
Box Settings R Press the {User Tools/Counter} key. Note ❒ When programming a password, a mark is displayed before the Box name. ❒ Specify a fax number, Internet Fax destination and IP-Fax destination as the transmission destination. ❒ The Fax Header is not printed on delivered documents. ❒ If a document cannot be delivered, a Communication Failure Report is printed and the document is saved as a Confidential Reception document. ❒ You can edit boxes in the same way you program them.
PAGE 188
Facsimile Features E If the password is programmed, enter a password using the number keys, and then press [OK]. If you make a mistake, press [Clear] or the {Clear/Stop} key, and then try again. 4 F Press [Delete]. To cancel deleting a box, press [Do not Delete]. The display returns to that of stepD. G Press [Exit]. H Press the {User Tools/Counter} key. Programming/Changing Information Boxes This section describes how to set up an Information Box.
PAGE 189
Box Settings E Select the box to program. When programming a new box, press [Not Programmed]. To change a box already programmed, press it, and then proceed to stepH. If a password is programmed, enter the password, press [OK], and then proceed to stepH. 4 F Press [Information Box]. G Enter a box name, and then press [OK]. H Enter the SEP Code. To change the SEP Code, press [Clear] or the {Clear/Stop} key, and then try again.
PAGE 190
Facsimile Features J Enter a password, and then press [OK]. If you make a mistake, press [Clear] or the {Clear/Stop} key before pressing [OK], and then try again. 4 K Re-enter the password, and then press [OK]. If you make a mistake, press [Clear] or the {Clear/Stop} key before pressing [OK], and then try again. L Press [OK]. M Press [Exit]. N Press the {User Tools/Counter} key. Note ❒ You can edit boxes in the same way you program them. However, boxes that are being used cannot be edited.
PAGE 191
Box Settings Deleting Information Boxes This section describes how to delete Information Boxes. Important ❒ If there are documents in the box, you cannot delete the box. A Press [Facsimile Features]. B Press [General Features]. C Press [Box Setting]. D Press [Delete], and then select the box you want to delete. 4 E If the password is programmed, enter a password using the number keys, and then press [OK]. If you make a mistake, press [Clear] or the {Clear/Stop} key, and then try again.
PAGE 192
Facsimile Features Programming/Changing Transfer Boxes This section describes how to set up an Transfer Box. This function turns the machine into a fax relay station. Documents sent with a SUB Code that matches the SUB Code programmed as a Transfer Box are received, and then relayed to a programmed receiver. Since documents can be sent to multiple destinations in a single transfer request, you can economize on call charges when sending to distant destinations.
PAGE 193
Box Settings E Select the box to program. When programming a new box, press [Not Programmed]. To change a box already programmed, press it, and then proceed to stepH. 4 F Press [Transfer Box]. G Enter a Box name, and then press [OK]. H Enter a SUB Code. To change the SUB Code, press [Clear] or the {Clear/Stop} key, and then try again. To change Box name, press [Box Name], and then repeat from stepG. I To Program End Receivers, Select an Receiving Station. You can store five Receiving Station.
PAGE 194
Facsimile Features J Specify End Receivers with Destination keys, and then press [OK]. 4 You can change the display to the fax destination, Internet fax destination, and IP-Fax destination using the key on the left side of the display. A reception station can also be registered as a group destination. In such a case, a maximum of 500 parties including End Receivers 1-5 can be specified in a group. To register another End Receiver, repeat from stepI. K To program a password, press [Password].
PAGE 195
Box Settings P Press the {User Tools/Counter} key. Note ❒ After documents are transferred, Transfer Result Reports are not sent back to the sender. ❒ Specify the Internet fax destination and IP-Fax destination as a reception station. ❒ After documents are transferred, they are deleted. ❒ When this function is set to on, the machine prints out the received documents it transfers and a Transfer Result Report after the transfer has finished.
PAGE 196
Facsimile Features E If the password is programmed, enter a password using the number keys, and then press [OK]. If you make a mistake, press [Clear] or the {Clear/Stop} key, and then try again. 4 F Press [Delete]. To cancel deleting a special sender, press [Do not Delete]. The display returns to that of stepD. G Press [Exit]. H Press the {User Tools/Counter} key. Printing the Box List Print a list showing the currently programmed Personal Boxes, Information Boxes, and Transfer Boxes.
PAGE 197
5. Printer Features This chapter describes user tools in the Printer Features menu. For details on how to access Printer Features, see "Accessing User Tools (System Settings)". Test Print This section describes the user tools in the Test Print menu under Printer Features. ❖ Multiple Lists You can print the configuration page and error log. ❖ Configuration Page You can print the machine's current configuration values. ❖ Error Log You can print error logs listing all errors that occurred during printing.
PAGE 198
Printer Features Printing the configuration page A Press [Printer Features]. B Press [Configuration Page] on the [List / Test Print]. 5 The configuration page is printed. C Press the {User Tools/Counter} key. Interpreting the configuration page ❖ System Reference • Unit Number Displays the serial number assigned to the board by its manufacturer. • Total Memory Displays the total amount of memory (SDRAM) installed on the printer.
PAGE 199
Test Print • Connection Equipment Displays the installed optional equipments. ❖ Paper Input Displays settings made under Tray Paper Settings menu. ❖ System Displays settings made under the System menu. ❖ PCL Menu Displays settings made under PCL Menu. ❖ PS Menu Displays settings made under PS Menu. ❖ PDF Menu Displays settings made under PDF Menu. ❖ Host Interface Displays settings made under the Host Interface menu.
PAGE 200
Printer Features Maintenance This section describes the user tools in the Maintenance menu under Printer Features. Default settings are shown in bold type. ❖ List / Test Print Lock You can lock the [List / Test Print] menu. • On • Off ❖ Delete All Temporary Print Jobs You can delete all print jobs temporarily stored in the machine. 5 ❖ Delete All Stored Print Jobs You can delete all print jobs stored in the machine.
PAGE 201
System System This section describes the user tools in the System menu under Printer Features. Default settings are shown in bold type. ❖ Print Error Report Select this to have an error report printed when a printer or memory error occurs. • On • Off ❖ Auto Continue You can select this to enable Auto Continue. When it is On, printing continues after a system error occurs.
PAGE 202
Printer Features ❖ Initial Print Job List You can set the desired type of print job list that appears on the screen when you press [Print Jobs]. • Complete List Displays the list of print jobs stored in the machine. • List Per User ID Displays the list of the User ID who stored a file in the machine. ❖ Memory Usage You can select the amount of memory used in Font Priority or Frame Priority, according to paper size or resolution. • Font Priority This setting uses memory for registering fonts.
PAGE 203
System ❖ Printer Language Specify the printer language. • Auto • PCL • PS • PDF This menu appears only when the PostScript 3 unit is installed. ❖ Sub Paper Size You can enable the Auto Substitute Paper Size (A4, LT) feature. • Auto • Off ❖ Page Size You can select the default paper size.
PAGE 204
Printer Features ❖ Default Printer Language You can set the default printer language if the machine cannot find the printer language automatically. • PCL • PS • PDF This menu appears only when the PostScript 3 unit is installed. ❖ Tray Switching You can set to switch the paper tray. • Off • On Reference p.3 “Accessing User Tools” 5 "Loading paper", Troubleshooting 194 From ManualsPrinter.
PAGE 205
Host Interface Host Interface This section describes the user tools in the Host Interface menu under Printer Features. Default settings are shown in bold type. ❖ I/O Buffer You can set the size of the I/O Buffer. Normally it is not necessary to change this setting. • 128KB • 256KB ❖ I/O Timeout You can set how many seconds the machine should wait before ending a print job. If data from another port usually arrives in the middle of a print job, you should increase this timeout period.
PAGE 206
Printer Features PCL Menu This section describes the user tools in the PCL Menu under Printer Features. Default settings are shown in bold type. ❖ Orientation You can set the page orientation. • Portrait • Landscape ❖ Form Lines You can set the number of lines per page. The number of lines can be specified from 5 to 128 by increments of one. Default: Metric version: 64, Inch version: 60 5 ❖ Font Source You can set the storage location of the default font.
PAGE 207
PCL Menu ❖ Symbol Set Specify the character set of the selected font. The available options are as follows: Roman-8, ISO L1, ISO L2, ISO L5, PC-8, PC-8 D/N, PC-850, PC-852, PC8-TK, Win L1, Win L2, Win L5, Desktop, PS Text, VN Intl, VN US, MS Publ, Math8, PS Math, VN Math, Pifont, Legal, ISO 4, ISO 6, ISO 11, ISO 15, ISO 17, ISO 21, ISO 60, ISO 69, Win 3.0 ❖ Courier Font You can select a courier font type.
PAGE 208
Printer Features PS Menu This section describes the user tools in the PS Menu under Printer Features. Default settings are shown in bold type. This menu appears only when the optional PostScript 3 unit is installed. 5 ❖ Data Format You can select a data format. • Binary Data • TBCP This setting is not effective when operating the machine with a parallel or EtherTalk connection.
PAGE 209
PDF Menu PDF Menu This section describes the user tools in the PDF Menu under Printer Features. Default settings are shown in bold type. ❖ Change PDF Password Set the password for the PDF file executing PDF Direct Print. • Current Password • New Password • Confirm New Password A password can be set using the Web Image Monitor, but in this case the password information is sent through the network. If security is a priority, set the password using this menu from the Control Panel.
PAGE 210
Printer Features ❖ Colour Profile You can set the colour profile. • Auto • Presentation • Solid Colour • Photographic • User Setting Reference p.3 “Accessing User Tools” 5 200 From ManualsPrinter.
PAGE 211
6. Scanner Features This chapter describes user tools in the Scanner Features menu. For details on how to access Scanner Features, see "Accessing User Tools (System Settings)". General Settings This section describes the user tools in the General Settings menu under Scanner Features. Default settings are shown in bold type. ❖ Switch Title Select the title to be shown on the destination list.
PAGE 212
Scanner Features ❖ Destination List Display Priority 2 In the machine’s address book, select which address book appears by default. You can select either [E-mail Address] or [Folder]. • E-mail Address • Folder 6 ❖ Print & Delete Scanner Journal Up to 100 transmission/delivery results can be checked on this machine. If the stored transmission/ delivery results reach 100, select whether to print the delivery journal. • On The transmission/delivery journal is printed automatically.
PAGE 213
Scan Settings Scan Settings This section describes the user tools in the Scan Settings menu under Scanner Features. Default settings are shown in bold type. ❖ A.C.S. Sensitivity Level Sets the sensitivity level for judging colour/black and white for scanning originals when [Scan Type] is set to [Auto Colour Select]. ❖ Wait Time for Next Orig.
PAGE 214
Scanner Features 6 ❖ Wait Time for Next Original(s): SADF When dividing originals and scanning them separately with the ADF to form a single file, select [Set Wait Time] or [Continuous Wait] for the waiting status. • Continuous Wait • Set Wait Time: 60 sec. This setting is valid if [SADF] is specified for [Original Feed Type] when scanning. If [Set Wait Time] is selected, enter the wait time in seconds (3-999) for placing additional originals with the number keys.
PAGE 215
Send Settings Send Settings This section describes the user tools in the Send Settings menu under Scanner Features. Default settings are shown in bold type. ❖ Compression (Black & White) Select whether or not to compress black and white scan files. • On • Off Compression reduces the time required for transferring the scan file. The actual time required for file transfer will vary depending on the file size and network load.
PAGE 216
Scanner Features ❖ Divide & Send E-mail This function is effective only when [On] is selected for [Max. E-mail Size]. Select whether or not an image exceeding the size specified in [Max. E-mail Size] should be divided and sent using more than one e-mail. • Yes (per Max. Size) • Yes (per Page) • Off When [Yes (per Max. Size)] is selected, enter the Max. Number of Divisions (2500) with the number keys.
PAGE 217
7. Registering Addresses and Users for Facsimile/Scanner Functions This chapter describes how to register destinations and users in the Address Book. For details on how to access System Settings, see "Accessing User Tools (System Settings)". Address Book Registering information such as the names of users and their e-mail addresses in the Address Book allows you to manage them easily. Important ❒ Address Book data is stored on the hard disk. It can be lost if there is some kind of hard disk failure.
PAGE 218
Registering Addresses and Users for Facsimile/Scanner Functions ❖ Protection You can set protection codes to stop sender's name from being used or folders from being accessed without authorization. ❖ Fax Dest. You can register fax numbers, line, fax header and select label insertion. When using IP-Fax, you can register the IP-Fax destination and select the protocol. 7 ❖ E-mail You can register e-mail destinations in the Address Book. 208 From ManualsPrinter.
PAGE 219
Address Book ❖ Folder You can register the protocol, path name and server name. • SMB • FTP • NCP 7 ❖ Add to Group You can put registered e-mail and folder destinations into a group for easier management. Downloaded From ManualsPrinter.
PAGE 220
Registering Addresses and Users for Facsimile/Scanner Functions Note ❒ You can also use a Web Image Monitor to register names in the Address Book. With the SmartDeviceMonitor for Admin, you can register multiple names at the same time. For details about using Web Image Monitor, see the Web Image Monitor Help. ❒ Using Address Management Tool in SmartDeviceMonitor for Admin, you can backup Address Book data. We recommend backing up data when using the Address Book.
PAGE 221
Address Book Sending scanned files to a shared folder directly After registering the path name, user name and password, you can connect to a shared folder simply by selecting the destination shown on the initial scanner display whenever sending files using the scanner function to a shared folder. To share the folder using Windows, select the SMB protocol. To register the folder to the FTP server, select the FTP protocol. To register the folder to the NetWare server, select the NCP protocol. Reference p.
PAGE 222
Registering Addresses and Users for Facsimile/Scanner Functions Registering Names Register user information including their names. The user name is useful for selecting a destination when sending faxes or e-mail. You can also use it as a folder destination. You can register up to 2000 names. Registering Names This section describes how to register names. A Press [System Settings]. 7 B Press [Administrator Tools]. C Press [Address Book Management]. D Check that [Program / Change] is selected.
PAGE 223
Registering Names H Press the key for the classification you want to use under Select Title. The keys you can select are as follows: • [Frequent]: Added to the page that is displayed first. • [AB], [CD], [EF], [GH], [IJK], [LMN], [OPQ], [RST], [UVW], [XYZ], [1] to [10]: Added to the list of items in the selected title. You can select [Frequent] and one more page for each title. I Press [OK] twice. J Press the {User Tools/Counter} key. Note ❒ The name can be used for documents in the Document Server.
PAGE 224
Registering Addresses and Users for Facsimile/Scanner Functions Changing a Registered Name This section describes how to change a name. A Press [System Settings]. B Press [Administrator Tools]. C Press [Address Book Management]. D Check that [Program / Change] is selected. E Select the registered name you want to change. 7 Press the name key, or enter the registered number using the number keys. F To change the name or key display, press [Change] on the right of the name or key display.
PAGE 225
Registering Names Deleting a Registered Name This section describes how to delete a name. A Press [System Settings]. B Press [Administrator Tools]. C Press [Address Book Management]. D Press [Delete]. E Select the name you want to delete. Press the name key, or enter the registered number using the number keys. 7 F Press [Yes]. G Press [Exit]. H Press the {User Tools/Counter} key. Downloaded From ManualsPrinter.
PAGE 226
Registering Addresses and Users for Facsimile/Scanner Functions Authentication Information Following describes the procedure for authenticating a user code. Important ❒ The functions associated with each user code are the same. If you change or delete user codes, management data and limits associated with that code become invalid.
PAGE 227
Authentication Information Registering a User Code This section describes how to register a user code. A Press [System Settings]. B Press [Administrator Tools]. C Press [Address Book Management]. D Check that [Program / Change] is selected. E Press the name whose code is to be registered, or enter the registered number using the number key. You can search by the registered name, fax number, folder name, e-mail address, or IP-Fax destination. 7 F Press [Auth. Info].
PAGE 228
Registering Addresses and Users for Facsimile/Scanner Functions I Select the functions to be used with the user code from Available Functions. J Press [OK]. K Press [Exit]. L Press the {User Tools/Counter} key. Note ❒ You can enter a one-to eight-digit user code. ❒ To register the name, see Registering Names". 7 Reference p.212 “Registering Names” Changing a User Code This section describes how to change a user code. Important ❒ Even if you change a user code, the counter value will not be cleared.
PAGE 229
Authentication Information D Check that [Program / Change] is selected. E Select the user whose user code you want to change. Press the name key, or enter the registered number using the number keys. You can search by the registered name, fax number, folder name, e-mail address, or IP-Fax destination. F Press [Auth. Info]. G Press [Change], and then enter the new user code using the number keys H Press {q} key. I To change the available functions, press [Auth. Info] and then press [TNext] 7 twice.
PAGE 230
Registering Addresses and Users for Facsimile/Scanner Functions Deleting a User Code This section describes how to delete a user code. Important ❒ After clearing the user code, the counter is automatically cleared. A Press [System Settings]. 7 B Press [Administrator Tools]. C Press [Address Book Management]. D Press [Delete]. E Select the name whose code is to be deleted. Press the name key, or enter the registered number using the number keys.
PAGE 231
Authentication Information J Press the {User Tools/Counter} key. Note ❒ To delete a name from the Address Book entirely, see "Deleting a Registered Name". Reference p.215 “Deleting a Registered Name” Displaying the Counter for Each User This section describes how to display the counter for each user. A Press [System Settings]. 7 B Press [Administrator Tools]. C Press [Display / Clear / Print Counter per User].
PAGE 232
Registering Addresses and Users for Facsimile/Scanner Functions B Press [Administrator Tools]. C Press [Display / Clear / Print Counter per User]. D Select a user code from the left side of the display. Press [Select All on the Page] to select all user codes on the page. E Press [Print Counter List] under Per User. 7 Enter the user code, and then press {q} if the user code is registered.
PAGE 233
Authentication Information Printing the Counter for All Users This section describes how to print the counter for all users. A Press [System Settings]. B Press [Administrator Tools]. C Press [Display / Clear / Print Counter per User]. D Press [Print Counter List] under All Users. 7 Enter the user code, and then press {q} if the user code is registered. E Select the function usage you want to print from [Copier Counter], [Print Counter], [Fax Counter], and [Scanner Counter]. F Press [Print].
PAGE 234
Registering Addresses and Users for Facsimile/Scanner Functions Clearing the Number of Prints This section describes how to clear the counter. A Press [System Settings]. B Press [Administrator Tools]. C Press [Display / Clear / Print Counter per User]. D Select the user code to clear. E To clear the number of prints made under a user code, select the user code 7 from the left side of the display. Press [Select All on the Page] to select all user codes on the page. F Press [Clear] under Per User.
PAGE 235
Fax Destination Fax Destination Register a fax destination so you do not need to enter fax numbers each time, and can send documents that have been scanned in using the facsimile function. • It is easy to select the fax destination if you register "Name" and "Key Display" for the fax destination. • You can register fax destinations as a group. For details about registering a group, see "Registering Names to a Group". • You can register fax destinations by selecting them from redial function.
PAGE 236
Registering Addresses and Users for Facsimile/Scanner Functions ❖ Label insertion Use label insertion to print information such as the destination name on the sheet printed out at the destination. Data is printed as follows: • Destination Name The destination name specified in [Fax Destination] is printed with "To" before it at the top of the sheet. • Standard Message A registered two-line sentence is printed under "Destination Name".
PAGE 237
Fax Destination Fax Destination This section describes how to register a fax number. Registering a Fax Destination A Press [System Settings]. B Press [Administrator Tools]. C Press [Address Book Management]. D Check that [Program / Change] is selected. E Select the name whose fax destination you want to register. Press the name 7 key, or enter the registered number using the number keys. F Press [Fax Dest.]. G Enter the fax number using the number keys, and then press [OK] under Facsimile No..
PAGE 238
Registering Addresses and Users for Facsimile/Scanner Functions I Press [OK]. Note ❒ When a group is registered, you can also add this fax destination to the group. For details about registering groups, see "Registering Names to a Group". ❒ To register the name, see "Registering Names". Reference p.212 “Registering Names” p.229 “Using a Fax Destination as a sender” p.229 “To change the line” p.230 “To change the SUB Code” p.230 “To change the SEP Code” p.230 “To set the International TX Mode” p.
PAGE 239
Fax Destination G Change the settings. H Press [OK]. Note ❒ To change the name, key display and title, see "Changing a Registered Name". Reference p.214 “Changing a Registered Name” p.229 “To change the fax number” p.229 “To change the line” p.230 “To change the SUB Code” p.230 “To change the SEP Code” p.230 “To set the International TX Mode” p.230 “To select the fax header” p.231 “To set label insertion” Using a Fax Destination as a sender A Press [Protection].
PAGE 240
Registering Addresses and Users for Facsimile/Scanner Functions To change the SUB Code A Press [Adv. Features], and then press [SUB Code]. B Press [Change] under TX SUB Code. C Enter the new SUB Code, and then press [OK]. D To change the password, press [Change] under Password (SID). E Enter the new password, and then press [OK]. F Press [OK]. To change the SEP Code 7 A Press [Adv. Features], and then press [SEP Code]. B Press [Change] under RX SEP Code. C Enter the new SEP Code, and then press [OK].
PAGE 241
Fax Destination To set label insertion When Label Insertion is set to ON, the receiver's name and standard messages are printed on the fax message when it is received at the other end. A Press [Change] under Label Insertion. B Press [On]. C Press [Change] under Line 2. D Select the new standard message or press [Manual Entry] to enter the new message. E Enter the new message, and then press [OK]. F Press [OK]. G Press [Change] under Line 3. H Select the new standard message, and then press [OK].
PAGE 242
Registering Addresses and Users for Facsimile/Scanner Functions C Press [Address Book Management]. D Press [Delete]. E Select the name whose fax destination you want to delete. Press the name key, or enter the registered number using the number keys. You can search by the registered name, fax number, folder name, e-mail address, or IP-Fax destination. F Press [Fax Dest.]. G Press [Change] under Facsimile No.. H Press [Delete All]. 7 I Press [OK] twice. J Press the {User Tools/Counter} key.
PAGE 243
Fax Destination IP-Fax Destination This section describes how to register a IP-Fax destination. Note ❒ For details about sending an IP-Fax, "Sending by IP-Fax", Facsimile Reference. Reference "Sending by IP-Fax", Facsimile Reference Registering an IP-Fax Destination A Press [System Settings]. 7 B Press [Administrator Tools]. C Press [Address Book Management]. D Check that [Program / Change] is selected. E Select the name whose IP-Fax destination you want to register.
PAGE 244
Registering Addresses and Users for Facsimile/Scanner Functions I Enter the IP-Fax destination. J Press [OK] twice. Note ❒ To register the name, see Registering Names". Reference p.212 “Registering Names” p.217 “Registering a User Code” p.259 “Registering Names to a Group” "Entering Text", About This Machine Changing a Registered IP-Fax Destination A Press [System Settings]. 7 B Press [Administrator Tools]. C Press [Address Book Management]. D Check that [Program / Change] is selected.
PAGE 245
Fax Destination G Press [Change] under "Fax Destination". H Enter the new destination, and then press [OK]. I Press [OK]. J Press [OK]. Note ❒ To change the name, key display and title, see "Changing a Registered Name". Reference p.214 “Changing a Registered Name” "Entering Text", About This Machine 7 Using the IP–Fax Destination as the sender A Press [Protection]. B Press [Sender] under [Use Name as]. To change the IP-Fax Destination A Press [Change] under [Use Name as].
PAGE 246
Registering Addresses and Users for Facsimile/Scanner Functions To program the SUB Code A Press [Adv. Features], and then press [SUB Code]. B Press [Change] under TX SUB Code. C Enter the SUB Code, and then press [OK]. D To enter a password, press [Change] under Password (SID). E Enter a password using the number keys, and then press [OK]. F Press [OK]. To program the SEP Code 7 A Press [Adv. Features], and then press [SUB Code]. B Press [Change] under RX SEP Code.
PAGE 247
Fax Destination Deleting a Registered IP-Fax Destination If you delete a destination that is a specified delivery destination, messages to its registered Personal Box, for example, cannot be delivered. Be sure to check the settings in the fax function before deleting any destinations. A Press [System Settings]. B Press [Administrator Tools]. C Press [Address Book Management]. D Press [Delete]. E Select the name whose IP-Fax destination you want to delete.
PAGE 248
Registering Addresses and Users for Facsimile/Scanner Functions E-mail Destination Register e-mail destinations so you do not need to enter an e-mail address every time, and can send scan files from scanner or fax function by e-mail. • It is easy to select the e-mail destination if you register "Name" and "Key Display" as the e-mail destination. • You can register e-mail destinations as a group. • You can use the e-mail address as the sender's address when sending scan files in scanner mode.
PAGE 249
E-mail Destination G Press [Change]. H Enter the e-mail address. 7 I Press [OK]. J Select [E-mail / Internet Fax Destination] or [Internet Fax Destination Only]. K If you want to use internet fax, specify whether or not to use " Send via SMTP Server". L Press [OK]. Note ❒ You can enter up to 128 characters for the e-mail address. ❒ To register the name, see Registering Names". Reference p.212 “Registering Names” p.217 “Registering a User Code” p.
PAGE 250
Registering Addresses and Users for Facsimile/Scanner Functions Changing an E-mail Destination A Press [System Settings]. B Press [Administrator Tools]. C Press [Address Book Management]. D Check that [Program / Change] is selected. E Select the name whose e-mail address you want to change. 7 Press the name key, or enter the registered number using the number keys. You can search by the registered name, fax number, folder name, e-mail address, or IP-Fax destination. F Press [E-mail].
PAGE 251
E-mail Destination Using the e-mail address as the sender A Press [Protection]. B Press [Sender] under [Use Name as]. Deleting an E-mail Destination A Press [System Settings]. B Press [Administrator Tools]. C Press [Address Book Management]. D Press [Delete]. E Select the name whose e-mail address you want to delete. 7 Press the name key, or enter the registered number using the number keys. You can search by the registered name, fax number, folder name, e-mail address, or IP-Fax destination.
PAGE 252
Registering Addresses and Users for Facsimile/Scanner Functions Registering Folders By registering a shared folder, you can send scan files to it directly. There are three types of protocol you can use: • SMB For sending files to shared Windows folders. • FTP Use when sending files to an FTP server. • NCP Use when sending files to an Net- Ware server. Note ❒ For details about protocols, server names, and folder levels, consult your network administrator.
PAGE 253
Registering Folders C Press [Address Book Management]. D Check that [Program / Change] is selected. E Select the name whose folder you want to register. Press the name key, or enter the registered number using the number keys. F Press [Auth. Info], and then press [Next]. G Press [Specify Other Auth. Info] on the right side of Folder Authentication. H Press [Change] under Login User Name. I Enter the login user name, and then press [OK]. J Press [Change] under Login Password.
PAGE 254
Registering Addresses and Users for Facsimile/Scanner Functions R Press [Exit]. Note ❒ To register the name, see Registering Names". ❒ ❒ ❒ ❒ You can enter up to 64 characters for the user name. You can enter up to 64 characters for the password. You can enter a path using up to 128 characters. To specify a folder, you can either enter the path manually or locate the folder by browsing the network. ❒ If the connection test fails, check the settings, and then try again.
PAGE 255
Registering Folders To locate the SMB folder using Browse Network A Press [Browse Network]. The client computers sharing the same network as the machine appear. Network display only lists client computers you are authorized to access. B Select a client computer. Shared folders under it appear. You can press [Up One Level] to switch between levels. C Select the folder you want to register. D [OK].
PAGE 256
Registering Addresses and Users for Facsimile/Scanner Functions Changing an SMB Folder A Press [System Settings]. B Press [Administrator Tools]. C Press [Address Book Management]. D Check that [Program / Change] is selected. E Select the name whose folder you want to change. 7 Press the name key, or enter the registered number using the number keys. You can search by the registered name, fax number, folder name, e-mail address, or IP-Fax destination. F Press [Folder].
PAGE 257
Registering Folders To change the protocol A Press [FTP] or [NCP]. B A confirmation message appears. Press [Yes]. Changing the protocol will clear all settings made under the previous protocol. C Enter each item again. Reference p.248 “Registering an FTP Folder” Deleting an SMB registered folder 7 A [System Settings]. B Press [Administrator Tools]. C Press [Address Book Management]. D Press [Delete]. E Select the name whose folder you want to delete.
PAGE 258
Registering Addresses and Users for Facsimile/Scanner Functions G Press the protocol which is not currently selected. A confirmation message appears. H Press [Yes]. I Press [OK]. J Press [Exit]. Note ❒ To delete the name, key display, and title, see "Deleting a Registered Name". Reference p.215 “Deleting a Registered Name” Using FTP to Connect Note ❒ To register a shared folder configured in Windows, see "Using SMB to Connect". ❒ To register a folder in an NetWare server, see "Using NCP to Connect".
PAGE 259
Registering Folders F Press [Auth. Info], and then press [Next]. G Press [Specify Other Auth. Info] on the right side of Folder Authentication. H Press [Change] under Login User Name. I Enter the login user name, and then press [OK]. J Press [Change] under Login Password. K Enter the password, and then press [OK]. L Enter the password again to confirm, and then press [OK]. M Press [Folder]. N Press [FTP]. 7 O Press [Change] under Server Name. P Enter the server name, and then press [OK].
PAGE 260
Registering Addresses and Users for Facsimile/Scanner Functions Y Press [Exit]. Note ❒ To register the name, see Registering Names". ❒ ❒ ❒ ❒ ❒ ❒ ❒ ❒ ❒ ❒ ❒ 7 ❒ You can enter up to 64 characters for the user name. You can enter up to 64 characters for the password. You can enter a server name using up to 64 characters. You can enter an absolute path, using this format: "/user/ home/username"; or a relative path, using this format: "directory/sub-directory".
PAGE 261
Registering Folders D Check that [Program / Change] is selected. E Select the name whose folder you want to change, and then press [Folder]. Press the name key, or enter the registered number using the number keys. You can search by the registered name, fax number, folder name, e-mail address, or IP-Fax destination. F Press [Folder]. G Select the items you want to change. H Press [Connection Test] to check the path is set correctly. I Press [OK]. J Press [Exit].
PAGE 262
Registering Addresses and Users for Facsimile/Scanner Functions Changing items under FTP A Press [Change] under Port No. B Enter the new port number, and then press {q}. C Press [Change] under Server Name. D Enter the new server name, and then press [OK]. E Press [Change] under "Path". F Enter the new path, and then press [OK]. Deleting an FTP Folder A Press [System Settings]. 7 B Press [Administrator Tools]. C Press [Address Book Management]. D Press [Delete].
PAGE 263
Registering Folders J Press [Exit]. Note ❒ To delete a name entirely, see "Deleting a Registered Name". Reference p.215 “Deleting a Registered Name” Using NCP to Connect Note ❒ To register a shared folder configured in Windows, see "Using SMB to Connect" ❒ To register a folder in an FTP server, see "Using FTP to Connect" Reference p.242 “Using SMB to Connect” p.248 “Using FTP to Connect” Registering an NCP Folder A Press [System Settings]. 7 B Press [Administrator Tools].
PAGE 264
Registering Addresses and Users for Facsimile/Scanner Functions I Enter the login user name, and then press [OK]. J Press [Change] under Login Password. K Enter the password, and then press [OK]. L Enter the password again to confirm, and then press [OK]. M Press [Folder]. N Press [NCP]. O Select "Connection Type". If you want to specify a folder in an NDS tree, press [NDS]. If you want to specify a folder on a NetWare server, press [Bindery]. P Specify the folder. Q Press [OK]. R Press [Exit].
PAGE 265
Registering Folders To locate the NCP folder manually A Press [Change] under Path. B Enter the path where the folder is located. C [OK]. D Press [Connection Test] to check the path is set correctly. E Press [Exit]. Note ❒ If you set "Connection Type" to [NDS], and if the NDS tree name is "tree", the name of the context including the volume is "context", the volume name is "volume" and the folder name is "folder", then the path will be "\\tree\volume. context\folder".
PAGE 266
Registering Addresses and Users for Facsimile/Scanner Functions Changing an NCP registered folder A Press [System Settings]. B Press [Administrator Tools]. C Press [Address Book Management]. D Check that [Program / Change] is selected. E Select the user of the registered folder you want to change. 7 Press the name key, or enter the registered number using the number keys. You can search by the registered name, fax number, folder name, e-mail address, or IP-Fax destination. F Press [Folder].
PAGE 267
Registering Folders To change the protocol A Press [SMB], or [FTP]. B A confirmation message appears. Press [Yes]. Changing the protocol will clear all settings made under the previous protocol. C Enter each item again. Reference p.242 “Registering an SMB Folder” p.248 “Registering an FTP Folder” Deleting an NCP Folder A Press [System Settings]. 7 B Press [Administrator Tools]. C Press [Address Book Management]. D Press [Delete]. E Select a user of the folder you want to delete.
PAGE 268
Registering Addresses and Users for Facsimile/Scanner Functions J [Exit]. Note ❒ To delete a name entirely, see Deleting a Registered Name". Reference p.215 “Deleting a Registered Name” 7 258 From ManualsPrinter.
PAGE 269
Registering Names to a Group Registering Names to a Group You can register names to a group to enable easy management of e-mail addresses and folders for each group. To add names to a group, the groups must be registered beforehand. Important ❒ When using Scan to Folder function, you cannot send scan files to a group with over 50 folders registered. ❒ The maximum number of destinations registerable to a group is 500.
PAGE 270
Registering Addresses and Users for Facsimile/Scanner Functions F Press [Change] under Group Name. G Enter the group name, and then press [OK]. The Key Display name is set automatically. H Press the title key under Select Title, if necessary. The keys you can select are as follows: • [Frequent]: Added to the page that is displayed first. • [AB], [CD], [EF], [GH], [IJK], [LMN], [OPQ], [RST], [UVW], [XYZ], [1] to [10]… Added to the list of items in the selected title.
PAGE 271
Registering Names to a Group B Press [Administrator Tools]. C Press [Address Book Management]. D Check that [Program / Change] is selected. E Select the name to register in a group. Press the name key, or enter the registered number using the number keys. You can search by the registered name, fax number, folder name, e-mail address, or IP-Fax destination. F Press [Add to Group]. G Select a group to which you want to add the name to.
PAGE 272
Registering Addresses and Users for Facsimile/Scanner Functions Adding a Group to Another Group You can add a group to another group. A Press [System Settings]. B Press [Administrator Tools]. C Press [Address Book: Program / Change / Delete Group]. D Check that [Program / Change] is selected. E Select the group that you want to put into another group. 7 Press the group key, or enter the registered number using the number keys.
PAGE 273
Registering Names to a Group G Select the group which you want to add to. The group key that you have selected becomes highlighted, and the group is added to it. 7 H Press [OK]. Downloaded From ManualsPrinter.
PAGE 274
Registering Addresses and Users for Facsimile/Scanner Functions Displaying Names Registered in a Group You can check the names or groups registered in each group. A Press [System Settings]. B Press [Administrator Tools]. C Press [Address Book: Program / Change / Delete Group]. D Check that [Program / Change] is selected. E Select the group where the members you want to check is registered. 7 You can search by the registered name, fax number, folder name, e-mail address, or IP-Fax destination.
PAGE 275
Registering Names to a Group D Check that [Program / Change] is selected. E Select the name to remove from a group. Press the name key, or enter the registered number using the number keys. You can search by the registered name, fax number, folder name, e-mail address, or IP-Fax destination. F Press [Add to Group]. G Select the group from which you want to remove the name. The group key that you have selected becomes highlighted, and the name is added to it. H Press [OK].
PAGE 276
Registering Addresses and Users for Facsimile/Scanner Functions Deleting a Group Within Another Group A Press [System Settings]. B Press [Administrator Tools]. C Press [Address Book: Program / Change / Delete Group]. D Check that [Program / Change] is selected. E Select the group that you want to delete from. 7 Press the group key, or enter the registered number during the number keys. You can search by the registered name, fax number, folder name, e-mail address, or IP-Fax destination.
PAGE 277
Registering Names to a Group H [OK]. Changing a Group Name A Press [System Settings]. 7 B Press [Administrator Tools]. C Press [Address Book: Program / Change / Delete Group]. D Check that [Program / Change] is selected. E Press the group key you want to change. You can search by the registered name, fax number, folder name, e-mail address, or IP-Fax destination. F To change the group name and key display, press [Change] under Group Name or Key Display. Downloaded From ManualsPrinter.
PAGE 278
Registering Addresses and Users for Facsimile/Scanner Functions G Enter the new group name or key display, and then press [OK]. H To change the title, press the title key under Select Title. I To change the registration number, press [Change] under Registration No.. J Enter the new registration number using the number keys. K Press the {q} key. L Press [OK]. Deleting a Group A Press [System Settings]. 7 B Press [Administrator Tools]. C Press [Address Book: Program / Change / Delete Group].
PAGE 279
Registering a Protection Code Registering a Protection Code You can stop sender's names or folders being accessed by setting a protection code. You can use this function to protect the following: • Folders You can prevent unauthorized access to folders. • Sender's names You can prevent misuse of sender's names. Reference p.217 “Registering a User Code” Registering a Protection Code to a Single User A Press [System Settings]. 7 B Press [Administrator Tools]. C Press [Address Book Management].
PAGE 280
Registering Addresses and Users for Facsimile/Scanner Functions G Press [Destination] or [Sender] under Use Name as. Both [Destination] and [Sender] can be selected at the same time. H Press [Change] under Protection Code. I Enter a protection code using the number keys, and then press {q}. J Press [OK]. K Press [Exit]. 7 Note ❒ Specify a protection code of up to eight digits. You can also specify "Protection" without specifying a protection code. 270 From ManualsPrinter.
PAGE 281
Registering a Protection Code Registering a Protection Code to a Group User A Press [System Settings]. B Press [Administrator Tools]. C Press [Address Book: Program / Change / Delete Group]. D Check that [Program / Change] is selected. E Press the group key you want to register or enter the registered number using the number keys. F Press [Protection]. G Press [Folder Destination] under Protection Object. H Press [Change] under Protection Code.
PAGE 282
Registering Addresses and Users for Facsimile/Scanner Functions Registering SMTP and LDAP Authentication SMTP Authentication For each user registered in the Address Book, you can register a login user name and login password to be used when accessing an SMTP server. To use an SMTP server, you need to program it beforehand. Important ❒ When [Do not Specify] is selected for SMTP Authentication, the User Name and Password that you have specified in SMTP Authentication of File Transfer settings applies.
PAGE 283
Registering SMTP and LDAP Authentication H Press [Change] under Login User Name. I Enter the login user name, and then press [OK]. J Press [Change] under Login Password. K Enter the password, and then press [OK]. L Enter the password again to confirm, and then press [OK]. M [OK]. Note ❒ To register the name, see Registering Names". ❒ You can enter up to 191 characters for the user name. ❒ When using POP before SMTP Authentication, you can enter up to 63 characters.
PAGE 284
Registering Addresses and Users for Facsimile/Scanner Functions LDAP Authentication For each user registered in the Address Book, you can register a login user name and login password to be used when accessing an LDAP server. To use an LDAP server, you need to program it beforehand. For details, see "LDAP Server Settings", Network Guide.
PAGE 285
Registering SMTP and LDAP Authentication H Press [Change] under Login User Name. I Enter the login user name, and then press [OK]. J Press [Change] under Login Password. K Enter the password, and then press [OK]. L Enter the password again to confirm, and then press [OK]. M Press [OK]. Note ❒ To register the name, see Registering Names".
PAGE 286
Registering Addresses and Users for Facsimile/Scanner Functions 7 276 From ManualsPrinter.
PAGE 287
8. Other User Tools Initial settings allow you switch the language as well as checking the number of printed papers by displaying the counter. For details on how to access respective settings, see "Accessing User Tools (System Settings)". Maintenance This section describes the user tools in Maintenance. [Maintenance] allows colour drift and gradient correction.
PAGE 288
Other User Tools Changing the Display Language You can change the language used on the display. English is set as default. A Press [Français]. The language is changed to French. B Press [Sortie]. 8 The menu appears in French. Reference p.3 “Accessing User Tools” 278 From ManualsPrinter.
PAGE 289
Enquiry Enquiry The enquiry function lets you check the telephone numbers to contact for repairs, or ordering consumables such as toner. Be sure to contact your service engineer to verify the following: ❖ Consumables • Telephone No. to order • Toner • Staple • Staple (Centre) • TX Stamp Name ❖ Machine Maintenance/Repair • Telephone No. • Serial No. of Machine ❖ Sales Representative • Telephone No. A Press [Enquiry]. 8 Enquiry information appears. B Press [Print Enquiry List].
PAGE 290
Other User Tools C Press the {Start} key. Enquiry information prints out. D Press [Exit] twice. Reference p.3 “Accessing User Tools” 8 280 From ManualsPrinter.
PAGE 291
Counter Counter Displaying the Total Counter You can display the total counter value used for all functions. A Press [Counter]. B To print a counter list, press [Print Counter List]. 8 C Press the {Start} key. A counter list prints out. Reference p.3 “Accessing User Tools” Downloaded From ManualsPrinter.
PAGE 292
Other User Tools 8 282 From ManualsPrinter.
PAGE 293
9.
PAGE 294
Appendix ❖ Copy paper size: • Trays: A3L-A5K, 11"×17"L-71/4"×101/2"L • Bypass:A3L-A6L, 11"×17"L-71/4"×101/2"L • Bypass (custom size): Vertical: 90.0-305.0mm, 3.55"-12.00" Horizontal: 148.0-600.0mm, 5.83"-23.62" • Duplex: A3L-A5K, 11"×17"L-101/2"L • LCT: A4K, 81/2"×11"K ❖ Paper weight: • Paper Tray: 60-216g/m2, 16-57lb. • Bypass: 60-253g/m2, 16-67lb. • Duplex: 64-169g/m2, 17-45lb.
PAGE 295
Specifications for the Main Unit ❖ Reproduction ratio: Preset reproduction ratios: Enlargement: Metric version Inch version 400% 400% 200% 200% 141% 155% 122% 129% 115% 121% Full size: Metric version Inch version 100% 100% Reduction: Metric version Inch version 93% 93% 82% 85% 75% 78% 71% 73% 65% 65% 50% 50% 25% 25% Zoom: From 25 to 400% in increments of 1% 9 ❖ Maximum continuous copy run: 999 sheets ❖ Paper capacity: • Tray1,2: 550 sheets (80g/m2, 20lb.
PAGE 296
Appendix ❖ Power consumption: Main unit only Complete system Warm-up about 1.5 kW about 1.5 kW Stand-by about 250 W about 280 W During printing about 1.2 kW about 1.3 kW Maximum about 1.5 kW about 1.5 kW The complete system consists of the main unit, booklet finisher, large capacity tray, file format converter, IEEE 802.11b (wireless LAN) interface unit, and USB Host interface unit. ❖ Dimensions (W × D × H up to exposure glass): 670×670×760mm, 26.8"×26.8"×30.
PAGE 297
Specifications for the Main Unit ❖ Noise emission: Sound power level: Main unit only Type 1 Type 2 Stand-by less than 44 dB(A) less than 44 dB(A) Copying less than 66 dB(A) less than 67 dB(A) Type 1 Type 2 Stand-by less than 45 dB(A) less than 45 dB(A) Copying less than 71 dB(A) less than 71 dB(A) Type 1 Type 2 Stand-by less than 32 dB(A) less than 32 dB(A) Copying less than 52 dB(A) less than 53 dB(A) Type 1 Type 2 Stand-by less than 33 dB(A) less than 33 dB(A) Copying less t
PAGE 298
Appendix Specifications for Options ❖ Exposure Glass Cover Lower this over originals for copying. ❖ Auto Document Feeder Lower this over originals for copying. • Mode: ADF mode, Batch mode, SADF mode, Mixed Size mode, Custom Size Originals mode, Auto detect (A4, 81/2"×11") • Original size: A3L-B6JISKL Vertical: 128-297mm, 5.1"-11.7" Horizontal: 128-432mm, 5.1"-17.3" • Maximum number of originals: 100 sheets (80g/m2, 20lb.) • Dimensions (W×D×H): 570×520×135mm, 22.8"×20.8"×5.4" • Weight: Approx. 12kg, 26.
PAGE 299
Specifications for Options • Stack capacity: No Staple: • 1,000 sheets: A4KL, B5JISKL, A5KL, 81/2"×11"KL, 81/2"×51/2"KL (80g/m2, 20lb.) • 500 sheets: A3L, B4JISL, 12"×18"L, 11"×17"L, 81/2"×14"L (80g/m2, 20lb.) Staple: • 2-9 sheets: 100 sets (A4K, 81/2"×11"K) (80g/m2, 20lb.) • 10-50 sheets:100–20 sets (A4K, 81/2"×11"K) (80g/m2, 20lb.) • 2-9 sheets: 100 sets (A4L, B5JISKL, 81/2"×11"L) (80g/m2, 20lb.) • 10-50 sheets: 50-10 sets (A4L, B5JISKL, 81/2"×11"L) (80g/m2, 20lb.
PAGE 300
Appendix 9 ❖ 3000-sheet Finisher Finisher Upper Tray: • Paper siez: A3L, B4JISL, A4KL, B5JISKL, A5KL, B6JISL, A6L, 12"×18"L, 11"×17"L, 81/2"×14"L, 81/2"×11"KL, 81/2"×51/2"L • Paper weight: 52-163g/m2, 14-43lb. • Stack capacity: • 250 sheets: A4KL, B5JISKL, A5KL, B6JISL, A6L, 81/2"×11"KL, 81/2"×51/2"L (80g/m2, 20lb.) • 50 sheets: A3L, B4JISL, 12"×18"L, 11"×17"L, 81/2"×14"L (80g/m2, 20lb.
PAGE 301
Specifications for Options • Staple paper size: A3L, B4JISL, A4KL, B5JISKL, 12"×18"L, 11"×17"L, 81/2"×14"L, 81/2"×11"KL • Staple paper weight: 64-90g/m2, 17-24lb. • Staple position • 1 staples - 3 positions • 2 staples - 2 positions • Power consumption: 96W (power is supplied from the main unit) • Dimensions (W×D×H) 657×613×960mm, 26.3"×24.5"×38.4" • Weight: Approx. 54kg, 119lb.
PAGE 302
Appendix 9 • Stack capacity: No Staple: • 2,000 sheets: A4K, 81/2"×11"K (80g/m2, 20lb.) • 1,000 sheets: A3L, B4JISL, A4L, B5JISKL, 12"×18"L, 11"×17"L, 81/2"×14"L, 81/2"×11"L (80g/m2, 20lb.) • 500 sheets: A5K (80g/m2, 20lb.) • 100 sheets: A5L, B6JISL, A6L, 81/2"×51/2"L (80g/m2, 20lb.) Staple: • 2-12 sheets: 150 sets (A4K, 81/2"×11"K) (80g/m2, 20lb.) • 13-50 sheets: 150-40(A4K, 81/2"×11"K) (80g/m2, 20lb.) • 2-9 sheets: 100 sets (A4L, B5JISKL, 81/2"×11"L) (80g/m2, 20lb.
PAGE 303
Specifications for Options • Saddle stitch • Paper size: A3L, B4JISL, A4L, B5JISL, 12"×18"L, 11"×17"L, 81/2"×14"L, 81/2"×11"L • Saddle stitching capacity: 2-15 sheets (80g/m2, 20lb.) • Stack capacity: 2-5 sheets: 30 sets (80g/m2, 20lb.) 6-10 sheets: 15 sets (80g/m2, 20lb.) 11-15 sheets: 10 sets (80g/m2, 20lb.) • Folding: Centre folding • Paper weight: 64-90g/m2, 17-24lb. • Position: 1 position • Power consumption: 96W (power is supplied from the main unit) • Dimensions (W×D×H) 657×613×960mm, 26.3"×24.
PAGE 304
Appendix ❖ 2 Tray Paper Unit • Paper size: A3L, B4JISL, A4KL, B5JISKL, A5K, 11"×17"L, 8 1 / 2 "×14"L, 81/2"×11"KL, 81/4"×14"L, 71/4"×101/2"KL, 8"×13"L, 81/2"×13"L, 81/4"×13"L, 8KL, 16KKL • Paper weight: 60-216g/m2, 16-57lb. • Paper capacity: 1,100 sheets (80g/m2, 20lb.) ×2 trays • Power consumption: Maximum 50W (power is supplied from the main unit) • Dimensions (W×D×H): 580×620×260mm, 22.9"×24.5"×10.3" • Weight: Approx. 25kg 55.2lb.
PAGE 305
Information about Installed Software Information about Installed Software expat • The software including controller, etc. (hereinafter "software") installed on this product uses the expat under the conditions mentioned below. • The product manufacturer provides warranty and support to the software of the product including the expat, and the product manufacturer makes the initial developer and copyright holder of the expat, free from these obligations.
PAGE 306
Appendix NetBSD 1. Copyright Notice of NetBSD For all users to use this product: This product contains NetBSD operating system: For the most part, the software constituting the NetBSD operating system is not in the public domain; its authors retain their copyright. The following text shows the copyright notice used for many of the NetBSD source code. For exact copyright notice applicable for each of the files/binaries, the source code tree must be consulted. A full source code can be found at http://www.
PAGE 307
Information about Installed Software • This product includes software developed by the University of California, Berkeley and its contributors. • This product includes software developed by Jonathan R. Stone for the NetBSD Project. • This product includes software developed by the NetBSD Foundation, Inc. and its contributors. • This product includes software developed by Manuel Bouyer. • This product includes software developed by Charles Hannum. • This product includes software developed by Charles M.
PAGE 308
Appendix Sablotron Sablotron (Version 0.82) Copyright © 2000 Ginger Alliance Ltd. All Rights Reserved a) The application software installed on this product includes the Sablotron software Version 0.82 (hereinafter, "Sablotron 0.82"), with modifications made by the product manufacturer. The original code of the Sablotron 0.82 is provided by Ginger Alliance Ltd., the initial developer, and the modified code of the Sablotron 0.82 has been derived from such original code provided by Ginger Alliance Ltd.
PAGE 309
Information about Installed Software SASL CMU libsasl Tim Martin Rob Earhart Rob Siemborski Copyright (c) 2001 Carnegie Mellon University. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: A Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
PAGE 310
Appendix MD4 Copyright (C) 1990-2, RSA Data Security, Inc. All rights reserved. License to copy and use this software is granted provided that it is identified as the "RSA Data Security, Inc. MD4 Message-Digest Algorithm" in all material mentioning or referencing this software or this function. License is also granted to make and use derivative works provided that such works are identified as "derived from the RSA Data Security, Inc.
PAGE 311
Information about Installed Software Samba(Ver 3.0.4) For SMB transmission, this machine uses Samba ver 3.0.4 (hereinafter referred to as Samba 3.0.4). Copyright © Andrew Tridgell 1994-1998 This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version.
PAGE 312
Appendix Open SSL Copyright (c) 1998-2004 The OpenSSL Project. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
PAGE 313
Information about Installed Software This product includes cryptographic software written by Eric Young (eay@cryptsoft.com). This product includes software written by Tim Hudson (tjh@cryptsoft.com). Original SSLeay License Copyright (C) 1995-1998 Eric Young (eay@cryptsoft.com) All rights reserved. This package is an SSL implementation written by Eric Young (eay@cryptsoft.com). The implementation was written so as to conform with Netscapes SSL.
PAGE 314
Appendix IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH A
PAGE 315
Information about Installed Software 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. Neither the name of the University nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
PAGE 316
Appendix THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
PAGE 317
Information about Installed Software THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
PAGE 318
Appendix - DES is now external, in the OpenSSL library - GMP is no longer used, and instead we call BN code from OpenSSL - Zlib is now external, in a library - The make-ssh-known-hosts script is no longer included - TSS has been removed - MD5 is now external, in the OpenSSL library - RC4 support has been replaced with ARC4 support from OpenSSL - Blowfish is now external, in the OpenSSL library [The licence continues] Note that any information and cryptographic algorithms used in this software are publicly
PAGE 319
Information about Installed Software IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF T
PAGE 320
Appendix 3. Neither the name of the University nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
PAGE 321
Information about Installed Software THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
PAGE 322
Appendix THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
PAGE 323
Information about Installed Software THIS SOFTWARE IS PROVIDED BY THE OPENLDAP FOUNDATION AND ITS CONTRIBUTORS ``AS IS'' AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
PAGE 324
INDEX 1 Sided to 2 Sided Auto Margin: TtoB, 100 1 Sided to 2 Sided Auto Margin: TtoT, 100 2 Sided Print, 130 4 Colour Graphic Mode, 190 A About Address Book, 207 Accessing User Tools, 3 A.C.S. Priority, 120 A.C.S. Sensitivity, 120 A.C.S.
PAGE 325
Copier / Document Server Features / Edit, 100 Copier / Document Server Features / General Features, 91 Copier / Document Server Features / Input/Output, 117 Copier / Document Server Features / Reproduction Ratio, 96 Copier / Document Server Features / Stamp, 106 Copies, 191 Copy Count Display, 47 Copy on Designating Page in Combine, 100 Copy Order in Combine, 100 Copy Orientation in Duplex Mode, 91 Counter, 281 Courier Font, 196 Cover Sheet Tray, 51 Customize Function: Copier, 91 Customize Function: Documen
PAGE 326
Font (Date Stamp), 111 Font Number, 196 Font (Page Numbering), 114 Font Pitch, 196 Font Source, 196 Format (Date Stamp), 111 Form Lines, 196 Forwarding, 130, 150, 163 Forwarding Mark, 153 Front Cover Copy in Combine, 100 Front Margin: Left / Right, 100 Front Margin: Top / Bottom, 100 Function Priority, 47 Function Reset Timer, 47 G General Features / Copier / Document Server Features, 91 General Features / Facsimile Features, 123 General Settings / Scanner Features, 201 General Settings / System Settings,
PAGE 327
Output: Document Server, 47 Output: Facsimile, 47 Output: Printer, 47 P Page Numbering, 114 Page Numbering in Combine (Page Numbering), 114 Page Numbering Initial Letter, 114 Page Size, 191 Panel key Sound, 47 Panel Off Timer, 57 Paper Display, 91 Paper Tray, 130, 164 Paper Tray Priority: Copier, 51 Paper Tray Priority: Facsimile, 51 Paper Tray Priority: Printer, 51 Paper Type: Bypass Tray, 51 Paper Type: Tray 1-4, 51 Parallel Communication Speed, 63 Parallel Interface, 63 Parallel Timing, 63 Parameter Set
PAGE 328
Registering a NCP Folder Destination, 253 Registering an E-mail Destination, 238 Registering an SMB Folder Destination, 242 Registering a Protection Code to a Group User, 271 Registering a Protection Code to a Single User, 269 Registering a User Code, 217 Registering Fax Information, 146, 147 Registering Folders, 242 Registering LDAP Authentication, 272, 274 Registering Names, 212 Registering Names to a Group, 260 Registering SMTP Authentication, 272 Registering user names and destination names, 212 Removin
PAGE 329
Setup Wireless LAN, 11 Shortcut R/E, 96 Signal Control, 63 Simplified Screen: Finishing Types, 117 SIP Settings, 136 Size (Background Numbering), 106 Size (Date Stamp), 111 Size (Page Numbering), 114 Slip Sheet Tray, 51 SMB Computer Name, 59 SMB Work Group, 59 SMTP Authentication, 69, 272 SMTP RX File Delivery Settings, 130 SMTP Server, 69 Special Senders to Treat Differently, 161 Specifications, 283 Specifications for the Main Unit, 283 Specify Tray for Lines, 130 SSID Setting, 66 Stamp Colour:1-4 (User St
PAGE 330
In accordance with IEC 60417, this machine uses the following symbols for the main power switch: a means POWER ON. c means STAND BY. Trademarks Microsoft®, Windows® and Windows NT® are registered trademarks of Microsoft Corporation in the United States and/or other countries. Acrobat® is a registered trademark of Adobe Systems Incorporated. NetWare is a registered trademark of Novell, Inc.
PAGE 331
Operating Instructions General Settings Guide Type for MP C3500/Aficio MP C3500/ISC 3535 Type for MP C4500/Aficio MP C4500/ISC 4045 AE AE B222-7858 Downloaded From ManualsPrinter.