Service manual

ENGINE SERVICE MODE
SM 5-57 G130/G131
Service Tables
5860 [SMTP/POP3/IMAP]
SMTP Auth *CTL [0 to 1 / 0 / 1/step]
0: Disable, 1: Enable
5860 003
Enables or disables the SMTP authentication for mail transfers.
SMTP Auth Encryp *CTL [0 to 2 / 0 / 1/step]
0: Automatic, 1: Not encrypt, 2: Encrypt
5860 006
Encrypts or does not encrypt passwords for SMTP authentications.
POP before SMTP *CTL [0 to 1 / 0 / 1/step]
0: Disable, 1: Enable
5860 007
Enables or disables the authentication that is executed on the POP server before
the communication is established with the SMTP server to transfer mails.
POP to SMTP Wait *CTL [0 to 10000 / 300 / 1 ms/step] 5860 008
Specifies the waiting time to access the SMTP server after the authentication on the
POP server.
Rcv Protocol *CTL [1 to 3 / 1 / 1 /step]
1: POP3, 2: IMAP4, 3: SMTP
5860 009
Sets the receiving protocol for receiving an e-mail.
POP Auth. Encrypt *CTL [0 to 2 / 0 / 1/step]
0: Automatic, 1: Not encrypt, 2: Encrypt
5860 013
Encrypts or does not encrypt passwords for POP3/IMAP4 authentications.
POP Server Port No. *CTL [1 to 65535 / 110 / 1/step] 5860 014
Specifies the port number of the POP server.
IMAP Srv Port No *CTL [1 to 65535 / 143 / 1/step] 5860 015
Specifies the port number of the IMAP4 server.
Receive Interval *CTL [2 to 1440 / 3 / 1 min/step] 5860 017
Specifies the interval for receiving an e-mail.
Mail Keep Sett. *CTL [0 to 2 / 0 / 1 /step]
0: No keep, 1: All, 2: Error mail
5860 019
Sets the mail type kept in the mail server after receiving an e-mail.
When you set the "1", all e-mails are kept in the mail server after receiving an e-
mail. When you set the "2", only error mails are kept in the mail server after
receiving an e-mail. When you set the "0", no e-mail is kept in the mail server after
receiving an e-mail.
Part. Mail Rcv Tm *CTL [1 to 168 / 72 / – ] 5860 020
Sets the amount of time to wait before saving a mail that breaks up during
reception. The received mail is discarded if the remaining portion of the mail is not
received during this prescribed time.
MDN Res RFC2298 *CTL [ 0 to 1 / 1 / – ]
0: No, 1: Yes
5860 021
Determines whether RFC2298 compliance is switched on for MDN reply mail.
SMTP From Replace *CTL [0 to 1 / 0 / 1/step] 5860 022
Determines whether the FROM item of the mail header is switched to the validated
account after the SMTP server is validated.
0: No. “From” item not switched, 1: Yes. “From” item switched.
SMTP Auth Direct [0 or 1 / 0 / – ]
Bit switch:
• Bit 0: LOGIN
• Bit 1: PLAIN
• Bit 2: CRAM MD5
• Bit 3: DIGEST MD5
• Bit 4 to 7: Not used
5860 025
Selects the authentication method for SMPT.
NOTE: This SP is activated only when SMTP authorization is enabled with UP
mode.