Service manual

ENGINE SERVICE MODE
G130/G131 5-16 SM
[Temp. Cor. 1] Fusing Temperature Correction (Correction Timing)
1913
Specifies the number of sheets to determine whether or not to apply the fusing
temperature correction. During a multi print job, the fusing temperature tends to
slightly overshoot around the 10th sheet and then stabilize. Temperature
overshooting may cause the glossiness to increase. To minimize the overshooting,
both fusing and pressure roller temperatures are decreased by the amount specified
in SP1-914 at the number of sheets specified in this SP mode, until the end of the
job. The temperatures are decreased in two steps.
Example: 162 mm/s line speed for G131
First step (also called 'Mode 1'): After 20 sheets (SP 1-913-2), temperature drops by
5°C (SP 1-914-2).
Second step (also called 'Mode 2'): After 50 sheets (SP 1-913-7), temperature drops
by 10°C (SP 1-914-7).
Narrow: LT/A4 SEF width or less
Wide: Wider than LT/A4 SEF
1913 001 Mode 1: H *BCU [1 to 255 / 20 / 1 sheet/step] Only for G130
1913 002 Mode 1: M *BCU
1913 003 Mode 1: L *BCU
1913 004 Mode 1 OHP narrow *BCU
1913 005 Mode 1: H: wide *BCU
[1 to 255 / 20
/ 1 sheet/step]
1913 006 Mode 2: H *BCU [1 to 255 / 50 / 1 sheet/step] Only for G130
1913 007 Mode 2: M *BCU
1913 008 Mode 2: L *BCU
1913 009 Mode 2: H: narrow *BCU
1913 010 Mode 2: H: wide *BCU
[1 to 255 / 50
/ 1 sheet/step]
[Temp. Cor. 2] Fusing Temperature Correction (Temperature Setting)
1914
Specifies the temperature to be subtracted from the target temperatures specified in
SP1-105-4 to-30.
Narrow: LT/A4 SEF width or less
Wide: Wider than LT/A4 SEF
1914 001 Temp 1:H *BCU
[0 to 20 / 5
/ 5°C /step] Only for G130
1914 002 Temp 1:M *BCU
[0 to 20 / 0
/ 5°C /step]
1914 003 Temp 1:L *BCU
[0 to 20 / 0
/ 5°C /step]
1914 004 Temp 1 OHP narrow *BCU
1914 005 Temp 1 OHP wide *BCU
[0 to 20 / 0
/ 5°C /step]
1914 006 Temp 2:H *BCU
[0 to 20 / 0
/ 5°C /step] Only for G130
1914 007 Temp 2:M *BCU
1914 008 Temp 2:L *BCU
[0 to 20 / 0
/ 5°C /step]
1914 009 Temp 2 OHP narrow *BCU
1914 010 Temp 2 OHP wide *BCU
[0 to 20 / 0
/ 5°C /step]
1915 [Stand-by Time]
Job Receiving *BCU [0 to 180 / 60 / 10 seconds/step]
0: The machine does not shift to the stand-by
mode.
1915 001
Specifies the time to shift the machine into the stand-by mode when not receiving a
print start command after receiving a print preparation command.
Job End *BCU [0 to 180 / 30 / 10 seconds/step]
0: The machine does not shift to the stand-by
mode.
1915 002
Specifies the time to shift the machine into the stand-by mode after the last job is
completed.