Paper type: Wood Free 80g/m2, Paper Thickness=100 µm // Pages in book=120 // Print scale=81% Gap (when printed at 81% scale) = Pages in book × Paper thickness / 2 = 6.000000 mm RICOH COMPANY, LTD. 15-5, Minami Aoyama 1-chome, Minato-ku, Tokyo 107-8544, Japan Phone: +81-(0)3-3479-3111 The Netherlands RICOH EUROPE B.V. Groenelaan 3, 1186 AA, Amstelveen Phone: +31-(0)20-5474111 Italy RICOH ITALIA SpA Via della Metallurgia 12, 37139 Verona Phone: +39-045-8181500 United Kingdom RICOH UK LTD.
Paper type: Wood Free 80g/m2, Paper Thickness=100 µm // Pages in book=120 // Print scale=81% Gap (when printed at 81% scale) = Pages in book × Paper thickness / 2 = 6.000000 mm Introduction This manual describes detailed instructions on the operation and notes about the use of this machine. To get maximum versatility from this machine all operators are requested to read this manual carefully and follow the instructions. Please keep this manual in a handy place near the machine.
JupP1k_GB_Mainte_F_FM.book Page i Thursday, August 22, 2002 4:23 PM Trademarks Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation in the United States and/or other countries. IPS-PRINT Printer Language Emulation Copyright© 1999-2000 Oak Technology, Inc., All rights reserved. Other product names used herein are for identification purposes only and might be trademarks of their respective companies. We disclaim any and all rights in those marks.
JupP1k_GB_Mainte_F_FM.book Page ii Thursday, August 22, 2002 4:23 PM Safety Information When using your printer, the following safety precautions should always be followed. Safety During Operation In this manual, the following important symbols are used: R WARNING: Indicates a potentially hazardous situation which, if instructions are not followed, could result in death or serious injury.
JupP1k_GB_Mainte_F_FM.book Page iii Thursday, August 22, 2002 4:23 PM R CAUTION: • Protect the machine from dampness or wet weather, such as rain and snow. • Unplug the power cord from the wall outlet before you move the machine. While moving the machine, you should take care that the power cord will not be damaged under the machine. • When you disconnect the power plug from the wall outlet, always pull the plug (not the cable).
JupP1k_GB_Mainte_F_FM.book Page iv Thursday, August 22, 2002 4:23 PM ENERGY STAR Program As an ENERGY STAR Partner, we have determined that this machine model meets the ENERGY STAR Guidelines for energy efficiency. The ENERGY STAR Guidelines intend to establish an international energy-saving system for developing and introducing energy-efficient office equipment to deal with environmental issues, such as global warming.
JupP1k_GB_Mainte_F_FM.book Page v Thursday, August 22, 2002 4:23 PM How to Read This Manual Symbols In this manual, the following symbols are used: R WARNING: This symbol indicates a potentially hazardous situation which, if instructions are not followed, could result in death or serious injury. R CAUTION: This symbol indicates a potentially hazardous situation which, if instructions are not followed, may result in minor or moderate injury or damage to property.
JupP1k_GB_Mainte_F_FM.book Page vi Thursday, August 22, 2002 4:23 PM TABLE OF CONTENTS 1. Replacing Consumables and Maintenance Kit Detaching the SR770 (2 Tray Finisher)..................................................... 1 Opening and Closing the Duplex Reversal Unit ...................................... 2 Replacing the Toner Cartridge .................................................................. 3 Replacing the Fuser Oil Unit .....................................................................
JupP1k_GB_Mainte_F_FM.book Page vii Thursday, August 22, 2002 4:23 PM 3. Paper and Other Media Paper and Other Media Supported by This Printer ............................... 47 Paper Sizes.................................................................................................. 47 Paper Recommendations ........................................................................ 53 Loading Paper..............................................................................................
JupP1k_GB_Mainte_F_FM.
JupP1k_GB_Mainte_F_FM.book Page 1 Thursday, August 22, 2002 4:23 PM 1. Replacing Consumables and Maintenance Kit Detaching the SR770 (2 Tray Finisher) There are times when you might have to detach the 2 Tray Finisher from the printer to remove misfed paper. This section describes how to detach the 2 Tray Finisher. A Hold the handle at the top of the 2 Important ❒ Be sure to attach the 2 Tray Finisher to the printer after closing the Duplex Reversal Unit. See p.
JupP1k_GB_Mainte_F_FM.book Page 2 Thursday, August 22, 2002 4:23 PM Replacing Consumables and Maintenance Kit Opening and Closing the Duplex Reversal Unit 1 There are times when you might have to detach the Duplex Reversal Unit to remove misfed paper. This section describes how to detach the Duplex Reversal Unit. A Push up the lock release button and keep it in place. Note ❒ You do not have to remove the External Tray even if the 2 Tray Finisher is attached. Th e D upl ex R ev er sal U n it is opened.
JupP1k_GB_Mainte_F_FM.book Page 3 Thursday, August 22, 2002 4:23 PM Replacing the Toner Cartridge Replacing the Toner Cartridge R WARNING: • Do not incinerate spilled toner or used toner. Toner dust is flammable and might ignite when exposed to an open flame. Disposal should take place at an authorized dealer or an appropriate collection site. If you dispose of the used toner cartridges yourself, dispose of them according to local regulations.
JupP1k_GB_Mainte_F_FM.book Page 4 Thursday, August 22, 2002 4:23 PM Replacing Consumables and Maintenance Kit B Remove the toner cartridge for the color you want to replace. A Unhook the green hook on the toner cartridge with one hand. 1 C Take out a new toner cartridge from the box. ZDJT202J ZDJT999J B Holding the toner cartridge with the other hand, pull out the cartridge up slowly. Note ❒ The black toner cartridge contains more than the other toner cartridges.
JupP1k_GB_Mainte_F_FM.book Page 5 Thursday, August 22, 2002 4:23 PM Replacing the Toner Cartridge E Holding the toner cartridge with the metal contact area in front, attach in the direction of the arrow. G Close the upper right cover. 1 ZDJH042J ZDJT004J Important ❒ Do not touch the metal contact point with your fingers. F Insert the toner cartridge slowly until the green hook snaps on the metal contact area. The following message appears on the panel display. Please wait a while. Loading Toner.
JupP1k_GB_Mainte_F_FM.book Page 6 Thursday, August 22, 2002 4:23 PM Replacing Consumables and Maintenance Kit Replacing the Fuser Oil Unit R CAUTION: • The Fusing Unit becomes very hot. When installing the new Fuser Oil Unit, turn off the printer and wait about an hour. After that, install the new Fusing Unit. Not waiting for the unit to cool down can result in a burn. 1 D If the External Tray is attached to the printer, raise it in the direction of the arrow (A A), and remove it (B B).
JupP1k_GB_Mainte_F_FM.book Page 7 Thursday, August 22, 2002 4:23 PM Replacing the Fuser Oil Unit G Holding the green handle, pull up the Fusing Unit slowly in the direction of the arrow. J Take out the Fuser Oil Unit from the bag, and remove seal (A A), and then remove seal (B B) as shown in the illustration. 1 ZDJH208J ZDJH053J Important ❒ Do not touch any areas other than the handle. H Put the removed Fusing Unit in a stable and level place.
JupP1k_GB_Mainte_F_FM.book Page 8 Thursday, August 22, 2002 4:23 PM Replacing Consumables and Maintenance Kit K Match (UU) on the front of the Fuser Oil Unit and the arrow on the Fusing Unit as shown in the illustration. 1 M Holding the green handle with one hand, use your other hand to push the front area of the handle to create a slight slant, and push the Fusing Unit slowly to the back. ZDJH055J Important ❒ Be careful not to get oil on the metal point of the left side of the Fuser Oil Unit.
JupP1k_GB_Mainte_F_FM.book Page 9 Thursday, August 22, 2002 4:23 PM Replacing the Fuser Oil Unit P If you removed the External Tray in step D, reattach it to the printer. Insert the hooks of the External Tray into the printer slits, and lower it toward you. 1 ZDJH010J Q If the Duplex Unit is installed, close the Duplex Reversal Unit. Reference See p.2 “Opening and Closing the Duplex Reversal Unit” R If the 2 Tray Finisher was installed, reattach the 2 Tray Finisher to the printer. Reference See p.
JupP1k_GB_Mainte_F_FM.book Page 10 Thursday, August 22, 2002 4:23 PM Replacing Consumables and Maintenance Kit Replacing the Photoconductor Unit If "Replace Black PCU (Type F)" appears on the panel display, replace the black Photoconductor Unit. 1 C Take out the green screwdriver. Use this screwdriver for all attachment and detachment of screws. Replace Black PCU (Type F) If "Replace Color PCU (Type A)" appears on the panel display, replace the three color Photoconductor Units.
JupP1k_GB_Mainte_F_FM.book Page 11 Thursday, August 22, 2002 4:23 PM Replacing the Photoconductor Unit F Lift the inner cover until it clicks into place and holds. G Remove the Photoconductor Unit you want to replace. For black, remove the upper left one, and for color, remove the three on the right. A Move the green hook slowly to the right as shown in the illustration. The green hook is located on the upper right of the Photoconductor Unit.
JupP1k_GB_Mainte_F_FM.book Page 12 Thursday, August 22, 2002 4:23 PM Replacing Consumables and Maintenance Kit C Lift and hold the green handle at the top (A A), and pull out the unit slowly (B B). B Place the Photoconductor Unit, and remove the adhesive tape at the tip of the unit. 1 ZDJH210J H Install a new Photoconductor Unit. For black, install one, and for color, install three. A Take the unit out from the bag.
JupP1k_GB_Mainte_F_FM.book Page 13 Thursday, August 22, 2002 4:23 PM Replacing the Photoconductor Unit Important ❒ If you do not attach the green arrow of the Photoconductor Unit securely to the rail, you might damage the Photoconductor Unit. ❒ Do not touch the light-sensitive area of the Photoconductor Unit. E Remove the cover and push in the Photoconductor Unit until it stops. J Tighten two screws using provided screwdriver.
JupP1k_GB_Mainte_F_FM.book Page 14 Thursday, August 22, 2002 4:23 PM Replacing Consumables and Maintenance Kit M Plug in the power cable and turn on the power switch. The following message appears on the panel display. The printer starts calibration. Please wait until it stops. 1 Calibrating... Important ❒ Do not turn off the power switch during calibration to avoid a printer malfunction.
JupP1k_GB_Mainte_F_FM.book Page 15 Thursday, August 22, 2002 4:23 PM Replacing the Development Unit Replacing the Development Unit If "Replace Black Dev. Unit(TypeD)" appears on the panel display, replace the black Development Unit. C Take out the green screwdriver. 1 Use this screwdriver for all attachment and detachment of screws. Replace Black Dev. Unit(TypeD) If "Replace Color Dev. Unit(TypeB)" appears on the panel display, replace the three color (CMY) Development Units. Replace Color Dev.
JupP1k_GB_Mainte_F_FM.book Page 16 Thursday, August 22, 2002 4:23 PM Replacing Consumables and Maintenance Kit F Lift the inner cover until it clicks into place and holds. 1 Important ❒ Pulling out the Development Unit quickly might cause it to drop. B Hold the right side of the Development Unit with your right hand, and pull out the unit slowly. ZDJH016J The Development Unit is installed shown in the illustration.
JupP1k_GB_Mainte_F_FM.book Page 17 Thursday, August 22, 2002 4:23 PM Replacing the Development Unit B Insert the Development Unit along the rail, and push in slowly until it stops. I Lower the inner cover slowly. 1 ZDJH018J ZDJH227E C Holding the Development Unit, pull out the tape slowly in a level manner. J Tighten two screws using provided screwdriver. ZDJH019J ZDJH039J Important ❒ Be sure to pull out the tape to avoid printer malfunction during operation. ❒ The removed tape is dirty.
JupP1k_GB_Mainte_F_FM.book Page 18 Thursday, August 22, 2002 4:23 PM Replacing Consumables and Maintenance Kit L Close the front cover slowly by pushing the two areas on the left and right. 1 ZDJH041J M Plug in the power cable and turn on the power switch. "Please Wait " appears on the panel display, and initial adjustments begin. Please wait until it stops. Please Wait Important ❒ Do not turn off the power switch during adjustments to avoid a printer malfunction.
JupP1k_GB_Mainte_F_FM.book Page 19 Thursday, August 22, 2002 4:23 PM Replacing the Fusing Unit Replacing the Fusing Unit R CAUTION: • The Fusing Unit becomes very hot. When installing the new Fusing Unit, turn off the printer and wait about an hour. After that, install the new Fusing Unit. Not waiting for the unit to cool down can result in a burn. D If the External Tray is attached to 1 the printer, raise it in the direction of the arrow (A A), and remove it (B B).
JupP1k_GB_Mainte_F_FM.book Page 20 Thursday, August 22, 2002 4:23 PM Replacing Consumables and Maintenance Kit G Holding the green handle, pull up the Fusing Unit slowly in the direction of the arrow, and then put it in a stable and level place. 1 J Match (UU) on the front of the Fus- er Oil Unit and the arrow on the Fusing Unit as shown in the illustration. ZDJH055J ZDJH208J H Take out the new Fusing Unit from the bag and put it in a stable and level place.
JupP1k_GB_Mainte_F_FM.book Page 21 Thursday, August 22, 2002 4:23 PM Replacing the Fusing Unit M Holding the green handle of the new Fusing Unit, use your other hand to push the area right in front of the handle to create a slight slant, and then push the Fusing Unit slowly to the back. O If you removed the External Tray in step D, reattach it to the printer. Insert the hooks of the External Tray into the printer slits, and lower it toward you.
JupP1k_GB_Mainte_F_FM.book Page 22 Thursday, August 22, 2002 4:23 PM Replacing Consumables and Maintenance Kit The following message appears on the panel display, and the printer starts color registration adjustment automatically. Please wait for a while. 1 B Pull out the Bypass Tray Extension, and then flip it open. Calibrating... After finishing adjustment, the following message appears. ZDJH203J Initializing...
JupP1k_GB_Mainte_F_FM.book Page 23 Thursday, August 22, 2002 4:23 PM Replacing the Fusing Unit U Confirm that the A3 paper which comes with the Fusing Unit is in the Bypass Tray, and then press {Enter} }. The printer prints 8 Test Sheet (A H). For details about Test Sheet, see p.41 “Test Sheet Samples”. Press {U} or {T} to select "0" or "1" as the values for A - H. Press {Enter} } to move to the next letter. After setting the value for "H", press {Enter} }, and the printer returns to the ready condition.
JupP1k_GB_Mainte_F_FM.book Page 24 Thursday, August 22, 2002 4:23 PM Replacing Consumables and Maintenance Kit Replacing the Dustproof Filter The dustproof filter is attached to the black Development Unit. When replacing the black Development Unit, also replace the dustproof filter. The dustproof filter is attached to the left side of the printer shown in the illustration. 1 C From the box which contained the black Development Unit, take out the new dustproof filter and glove.
JupP1k_GB_Mainte_F_FM.book Page 25 Thursday, August 22, 2002 4:23 PM Replacing the Dustproof Filter E With the hand wearing the glove, take out the dustproof filter that is attached to the dustproof filter cover slowly, one by one, and put them into the box which contained the black Development Unit. F Attach the new dustproof filters to the dustproof filter cover one by one. A Attach the large filter. 1 ZDJH216J B Attach the small filter.
JupP1k_GB_Mainte_F_FM.book Page 26 Thursday, August 22, 2002 4:23 PM Replacing Consumables and Maintenance Kit Replacing the Waste Toner Bottle If "Replace Waste Toner (Type E)" appears on the panel display, replace the waste toner bottle. 1 D Remove the used waste toner bottle slowly from inside the printer. Replace Waste Toner (Type E) A Turn off the power switch and unplug the power cable. B Open the front cover slowly by pulling down from the two areas on the left and right.
JupP1k_GB_Mainte_F_FM.book Page 27 Thursday, August 22, 2002 4:23 PM Replacing the Waste Toner Bottle G Insert the new waste toner bottle in the position shown in the illustration. J Plug in the power cable and turn on the power switch. 1 ZDJH230J H Push it in until it stops. ZDJH231J Important ❒ Be sure to insert the waste toner bottle firmly to avoid the toner from leaking inside the printer. I Close the front cover slowly by pushing the two areas on the left and right.
JupP1k_GB_Mainte_F_FM.book Page 28 Thursday, August 22, 2002 4:23 PM Replacing Consumables and Maintenance Kit Replacing the Paper Feed Rollers Note ❒ The following illustrations are the an examples of replacing the paper feed rollers of Tray 1. The same procedure is followed with the other trays. 1 C Pull out all trays slowly while lifting it up a little. A Check the contents of the box.
JupP1k_GB_Mainte_F_FM.book Page 29 Thursday, August 22, 2002 4:23 PM Replacing the Paper Feed Rollers E While pushing the pin of the paper feed roller A outwards (A A ), remove the paper feed roller (B B). H Hold the new paper feed roller C with its gear towards the shaft. Insert it into the rear shaft so that the roller gear is meshed with the shaft gear (A A ). Lock the roller with the stopper (B B).
JupP1k_GB_Mainte_F_FM.book Page 30 Thursday, August 22, 2002 4:23 PM Replacing Consumables and Maintenance Kit J Hold the new paper feed roller A with its pin towards you (A A). Insert the roller onto the front shaft until it clicks into place (B B). 1 ZERH090E K Slide all trays back into the printer slowly until it stops. Note ❒ If you replaced the paper feed rollers of the optional 2000sheet Large Capacity Tray, load stocks that you removed at step B in the tray.
JupP1k_GB_Mainte_F_FM.book Page 31 Thursday, August 22, 2002 4:23 PM 2. Cleaning and Adjusting the Printer Cautions to Take When Cleaning R WARNING: • Do not remove any covers or screws other than those specified in this manual. Some parts of the machine are at a high voltage and could give you an electric shock. Also, if the machine has laser systems, direct (or indirect) reflected eye contact with the laser beam may cause serious eye damage.
JupP1k_GB_Mainte_F_FM.book Page 32 Thursday, August 22, 2002 4:23 PM Cleaning and Adjusting the Printer Cleaning the Registration Roller R CAUTION: • The inside of the printer becomes very hot. Do not touch the parts with a label indicating the "hot surface", otherwise it could cause a burn. 2 C Wipe around the registration roller by turning with a soft damp cloth. Clean the roller when replacing the black Development Unit. A Turn off the power switch and unplug the power cable.
JupP1k_GB_Mainte_F_FM.book Page 33 Thursday, August 22, 2002 4:23 PM Cleaning the DustProof Glass Cleaning the DustProof Glass The dustproof glass may require cleaning if white lines appear on the print side of the document. A Turn C Slide the cleaning brush in and out slowly 8 to 10 times to clean all four areas. off the power switch and unplug the power cable. 2 B Open the front cover and remove the cleaning brush. ZDJP707J ZDJP705J There are four holes for cleaning the dustproof glass.
JupP1k_GB_Mainte_F_FM.book Page 34 Thursday, August 22, 2002 4:23 PM Cleaning and Adjusting the Printer Adjusting the Color Registration 2 When the printer is moved, when the Fusing Unit is replaced, or after printing repeatedly for some time, registration shifting might occur. By performing color registration adjustment, you can maintain optimum print results. C Press {U} or {T} to display "Color Note ❒ Normally, do not perform manual color adjustment. played, and then press {Enter} }.
JupP1k_GB_Mainte_F_FM.book Page 35 Thursday, August 22, 2002 4:23 PM Adjusting the Color Registration Automatic color adjustment takes about two minutes. When it completes, a check message is displayed. A Press {Menu}}. Completed 2 Press {Enter} } to return to the color adjustment menu. Color Regist.: Auto Adjust G When you have made all the set- tings, press {On Line} }. "Ready " appears on the panel display. Ready Fuser Adjust ZDJS001J "Menu" appears on the panel display.
JupP1k_GB_Mainte_F_FM.book Page 36 Thursday, August 22, 2002 4:23 PM Cleaning and Adjusting the Printer Important ❒ When the toner cartridge is almost empty or "Auto Adjust” is not finished, the following message appears on the panel display and Fuser Adjust is not available. 2 Cannot Adjust See User’s Guide Confirm that the toner cartridge is installed. The toner cartridge must be installed. See p.3 “Replacing the Toner Cartridge”. If the toner cartridge is installed, perform "Auto Adjust". See p.
JupP1k_GB_Mainte_F_FM.book Page 37 Thursday, August 22, 2002 4:23 PM Adjusting the Color Registration D Press {U} or {T} to display "Color When color shifting occurs Regist.", and then press {Enter} }. Perform this procedure when color shifting occurs even after performing "Auto Adjust". L or larger paper in the A Load A4L Bypass Tray. Maintenance: Color Regist. E Press {U} or {T} to display "Fuser 2 Adjust", and then press {Enter} }. Note ❒ Be sure to select paper size in the "Paper Input" menu.
JupP1k_GB_Mainte_F_FM.book Page 38 Thursday, August 22, 2002 4:23 PM Cleaning and Adjusting the Printer G Press {U} or {T} to display the paper types and resolution in which color shifting occurs, and then press {Enter} }. Custom Adjust: Plain: 600dpi 2 Select a value from "Plain: 600dpi", " P la i n : 1 20 0 d p i " a n d " T h i c k : 600dpi". Note ❒ The current resolution is displayed on the printer driver properties.
JupP1k_GB_Mainte_F_FM.book Page 39 Thursday, August 22, 2002 4:23 PM Adjusting the Color Registration E Confirm that "Print" is displayed Manual Adjust Important ❒ Normally, do not perform manual color adjustment. A Press {Menu}}. in the menu for printing the Test Sheet, and then press {Enter} }. Test Sheet: Print 2 The Test Sheet is printed. See p.41 “Test Sheet Samples”. F Enter the corrective values for A through L on the Test Sheet in order. Adjustment A: (-7.0 +7.
JupP1k_GB_Mainte_F_FM.book Page 40 Thursday, August 22, 2002 4:23 PM Cleaning and Adjusting the Printer B Press {Enter} }. C Make the settings for "B" to "L" in the same manner, using steps A and B. D When you finish the settings up to "L", press {Enter} } in the next menu. 2 Manual Adjust: Print Result The Test Sheet is printed. See p.41 “Test Sheet Samples”. Printing... E Confirm that square "0" is the whitest within A through L on the printed Test Sheet.
JupP1k_GB_Mainte_F_FM.book Page 41 Thursday, August 22, 2002 4:23 PM Adjusting the Color Registration Test Sheet Samples Following images are samples for the test sheet.
JupP1k_GB_Mainte_F_FM.
JupP1k_GB_Mainte_F_FM.book Page 43 Thursday, August 22, 2002 4:23 PM Adjusting the Image Density Adjusting the Image Density Adjust the image density when the print side of the page is a hazy gray or the print image looks patchy. Important ❒ Extreme settings may create output that appears dirty. ❒ Image density settings should be made from the application or the printer driver whenever possible. Note ❒ Changing the image density setting might cause a deterioration of color balance.
JupP1k_GB_Mainte_F_FM.book Page 44 Thursday, August 22, 2002 4:23 PM Cleaning and Adjusting the Printer Adjusting the Registration of the Trays You can adjust the registration of each tray. The vertical adjustment is used for all trays. Normally, you need not update the registration. But when the optional Paper Feed Unit or the Duplex Unit is installed, updating the registration is useful in some cases. The following procedure describes how to adjust Tray 3.
JupP1k_GB_Mainte_F_FM.book Page 45 Thursday, August 22, 2002 4:23 PM Adjusting the Registration of the Trays B Press {U} or {T} to display the "Adjustment", and then press {Enter} }. Registration: Adjustment F Print the test sheet to check the settings you have made. G Press {On Line}}. "Ready " appears on the panel display. C Press {U} or {T} to display the tray to adjust, and then press {Enter} }. 2 Ready Adjustment: Vert.
JupP1k_GB_Mainte_F_FM.
JupP1k_GB_Mainte_F_FM.book Page 47 Thursday, August 22, 2002 4:23 PM 3. Paper and Other Media Paper and Other Media Supported by This Printer Paper Sizes This section describes the type, size, feed direction, and maximum amount of paper that can be loaded into each paper tray in this printer. Note ❒ The following symbols and terminology are used to represent the feed direction.
JupP1k_GB_Mainte_F_FM.book Page 48 Thursday, August 22, 2002 4:23 PM L 216 × 356 L 216 × 279 K 279 × 216 51/2" × 81/2" L 140 × 216 L 184 × 276 K 276 × 184 Folio (8 /4" × 13") L 210 × 330 1 Foolscap (F4, 8 /2" × 13") L 216 × 330 F/GL (8" × 13") L 203 × 330 1 Com#10 Env (9 /2" × 4 /8") K 241.3 × 104.8 C5 Env (9.02" × 6.38") K 229 × 162 C6 Env (6.38" × 4.49") K 162 × 114 DL Env (8.66" × 4.33") K 220 × 110 Monarch Env (7 /2" × 3 /8") K 190.5 × 98.
JupP1k_GB_Mainte_F_FM.book Page 49 Thursday, August 22, 2002 4:23 PM Paper and Other Media Supported by This Printer 11" × 17" Legal (LG) L 81/2" × 14" Letter (LT) L 81/2" × 11" K 11" × 81/2" 51/2" × 81/2" L 51/2" × 81/2" Executive (Exec.) L 71/4" × 101/2" K 101/2" × 71/4" A3 L 11.26" × 16.54" B4 JIS L 10.12" × 14.33" A4 L 8.26" × 5.83" K 5.83" × 8.26" L 7.17" × 10.12" K 10.12" × 7.17" L 5.83" × 8.26" B5 JIS A5 K 8.26" × 5.83" B6 JIS L 5.04" × 7.17" A6 L 4.
JupP1k_GB_Mainte_F_FM.book Page 50 Thursday, August 22, 2002 4:23 PM Paper and Other Media • • • • • 3 • means that the size is exclusive. means that the size is supported and printer select the paper size automatically. means that the size is supported but the paper size should be selected with the control panel. means that the size is supported but the paper size should be set with the control panel as a custom size. * means that the supported size is approximately 3.
JupP1k_GB_Mainte_F_FM.book Page 51 Thursday, August 22, 2002 4:23 PM B6 JIS L 128 × 182 A6 L 105 × 148 11" × 17" L 279 × 432 Legal (LG, 81/2" × 14") L 216 × 356 Letter (LT, 81/2" × 11") L 216 × 279 K 279 × 216 51/2" × 81/2" L 140 × 216 Executive (Exec., 71/4" × 101/2") L 184 × 276 K 276 × 184 Folio (8 /4" × 13") L 210 × 330 Foolscap (F4, 81/2" × 13") L 216 × 330 F/GL (8" × 13") L 203 × 330 Com#10 Env (9 /2" × 41/8") K 241.3 × 104.8 CA Env (9.02" × 6.
JupP1k_GB_Mainte_F_FM.book Page 52 Thursday, August 22, 2002 4:23 PM Paper and Other Media Legal (LG) L 81/2" × 14" Letter (LT) L 81/2" × 11" K 11" × 81/2" 51/2" × 81/2" L 51/2" × 81/2" Executive (Exec.) L 71/4" × 101/2" K 101/2" × 71/4" A3 L 11.26" × 16.54" B4 JIS L 10.12" × 14.33" A4 L 8.26" × 5.83" K 5.83" × 8.26" L 7.17" × 10.12" K 10.12" × 7.17" L 5.83" × 8.26" K 8.26" × 5.83" B6 JIS L 5.04" × 7.17" A6 L 4.13" × 5.
JupP1k_GB_Mainte_F_FM.book Page 53 Thursday, August 22, 2002 4:23 PM Paper Recommendations Paper Recommendations Loading Paper Important ❒ Do not use paper that is meant for an ink-jet printer or it may stick to the Fusing Unit and cause a paper misfeed. ❒ When printing on an OHP transparency that has a print side, load it with the print side over on the Bypass Tray. Not taking this precaution may cause it to stick to the Fusing Unit and cause a misfeed.
JupP1k_GB_Mainte_F_FM.book Page 54 Thursday, August 22, 2002 4:23 PM Paper and Other Media Types of Paper and Other Media ❖ Plain Paper • Tray 1/2 can hold up to 500 sheets. PAPER FEED UNIT Type 3800C (500x1) can hold up to 500 sheets. PAPER FEED UNIT Type 3800C (500x2) can hold up to 1000 sheets. Paper Bank PS470 can hold up to 2000 sheets. Confirm that the top of the stack is not higher than the limit mark inside the tray.
JupP1k_GB_Mainte_F_FM.book Page 55 Thursday, August 22, 2002 4:23 PM Paper Recommendations ❖ Envelopes Important ❒ Only envelopes A and B as shown below are supported. Supported *1 Supported *1 3 Not supported *1 Misfeeds also might occur when using envelopes A and B depending on the length and shape of the flaps. • When printing on envelopes, use the bypass tray, and select "Thick Paper" as a paper type in the "Paper Input" menu on the control panel. ⇒ p.
JupP1k_GB_Mainte_F_FM.book Page 56 Thursday, August 22, 2002 4:23 PM Paper and Other Media • Make the printer driver's setting for rotating the print image by 180 degrees. For details, see the Help file for the printer driver. • Confirm that there is no air in the envelopes before loading. • To get better print quality, it is recommended that you set the right, left, top, and bottom print margin, to at least 15 mm (0.6") each. • Do not print on both sides of envelopes.
JupP1k_GB_Mainte_F_FM.book Page 57 Thursday, August 22, 2002 4:23 PM Printable Area Printable Area The following shows the printable area for this printer. Be sure to set the print margins correctly by the application. 4.2mm (0.166 inch) Feed Direction 4.2mm (0.166 inch) 4.2mm (0.166 inch) 3 4.2mm (0.166 inch) A : printable area Note ❒ The printable area may vary depending on the paper size, printer language and printer driver settings.
JupP1k_GB_Mainte_F_FM.book Page 58 Thursday, August 22, 2002 4:23 PM Paper and Other Media Loading Paper Load paper and change the paper size in Tray 1, Tray 2 and the optional Paper Feed Unit by following the procedures below. Important ❒ Tray 1 uses A4 K paper exclusively. Load only A4 paper at all times. ❒ 2000-sheet Large Capacity Tray uses A4 K paper exclusively. Load only A4 paper at all times.
JupP1k_GB_Mainte_F_FM.book Page 59 Thursday, August 22, 2002 4:23 PM Loading Paper Loading Paper in Tray 2 and the Optional Paper Feed Unit This section describes loading paper which is different from default size in Tray 2. D Pinching both sides of the end guide (A A), move the end guide in the direction of the arrow to open it. A Pull out the Paper Tray slowly until it stops. 3 ZDJY801J E Load paper in the same direction. ZDJH005J B Set the paper guide lock to the "unlocked" position.
JupP1k_GB_Mainte_F_FM.book Page 60 Thursday, August 22, 2002 4:23 PM Paper and Other Media G Make sure the paper is fixed in place, and then lock the side guide. 3 ZDJY007J H Pinching both sides of the end guide (A A), move the end guide toward the paper stack until it stops (B B). Loading paper in Paper Bank PS470 (2000-sheet Large Capacity Tray) Important ❒ 2000-sheet Large Capacity Tray uses A4 K paper exclusively. Load only A4 paper at all times.
JupP1k_GB_Mainte_F_FM.book Page 61 Thursday, August 22, 2002 4:23 PM Loading Paper Important ❒ Align the paper and load them against the left and right walls, or a paper misfeed might occur. This section uses Letter (81/2 × 11) L as an example. A Press {Menu}}. ❒ Confirm that the top of the stack is not higher than the limit mark inside the tray. C Push in the Paper Tray slowly until it stops.
JupP1k_GB_Mainte_F_FM.book Page 62 Thursday, August 22, 2002 4:23 PM Paper and Other Media E Press {U} or {T} to display the loaded paper size, and then press {Enter} }. Input", and then press {Enter} }. Menu: Paper Input Tray 2 : 8 1/2 x 11 After about two seconds, the display is returned to the menu. F Press {On Line}}. 3 H Press {U} or {T} to display "Paper "Ready " appears on the panel display. Ready This completes the change in setting.
JupP1k_GB_Mainte_F_FM.book Page 63 Thursday, August 22, 2002 4:23 PM Loading Paper D Press {U} or {T} to display the Changing the paper type By selecting the paper type you want to load, the printer can execute better printing. You can select from the following paper types. • Plain Paper, Recycled Paper, Special Paper, Color Paper, Letterhead Paper, Preprinted Paper, Prepunched Paper, Bond Paper, Card Stock A Press {Menu}}. target paper tray, and then press {Enter} }.
JupP1k_GB_Mainte_F_FM.book Page 64 Thursday, August 22, 2002 4:23 PM Paper and Other Media Load Paper in the Bypass Tray Besides regular paper, you can load thick paper, envelopes, OHP transparencies, and paper that is longer than A3L onto the Bypass Tray, which cannot be loaded in the Paper Trays or Paper Feed Unit. Note ❒ Paper sizes supported by the Bypass Tray are 90 - 305 mm in width, and 148 - 458 mm in length.
JupP1k_GB_Mainte_F_FM.book Page 65 Thursday, August 22, 2002 4:23 PM Loading Paper B Slide the side guides outward (A A), and then load paper until it stops with the print side up (B B). D Set the paper size using the control panel as follows: A Press {Menu} }. 3 ZDJH204J C Adjust the side guides to the paper width. ZDJS001J "Menu" appears on the panel display B Press {U} or {T} to "Paper Input" menu, and then press {Enter} }. The following message appears on the panel display.
JupP1k_GB_Mainte_F_FM.book Page 66 Thursday, August 22, 2002 4:23 PM Paper and Other Media E Press {On Line} }. "Ready " appears on the panel display. Ready B Press {U} or {T} to display "Paper Input", and then press {Enter} }. The following message appears on the panel display. Menu: Paper Input Specifying a custom paper size for the Bypass Tray 3 Important ❒ The paper size selected with the printer driver overrides the one selected with the control panel.
JupP1k_GB_Mainte_F_FM.book Page 67 Thursday, August 22, 2002 4:23 PM Loading Paper G Press {On Line}}. A Press {Menu}}. The following message appears on the panel display. Ready Specifying a paper type for the Bypass Tray By selecting the paper type you want to load, the printer can execute better printing. You can select from the following paper types.
JupP1k_GB_Mainte_F_FM.book Page 68 Thursday, August 22, 2002 4:23 PM Paper and Other Media E Press {U} or {T} to display the target paper type, and then press {Enter} }. Bypass Tray: *Thick Paper After about two seconds, the display is returned to the menu. F Press {On Line}}. 3 The following message appears on the panel display.
JupP1k_GB_Mainte_F_FM.book Page 69 Thursday, August 22, 2002 4:23 PM 4. Troubleshooting Error & Status Messages on the Control Panel ❖ Status Messages Messages/Second messages Description Solution Calibrating... The printer is calibrating the color. Energy Save Mode In Energy Save Mode Level 2. No action required. Hex Dump Mode In Hex Dump Mode. Loading Toner... The printer is loading the ton- Wait for a while. er. Offline The printer is offline and cannot print data. Press {On Line} }.
JupP1k_GB_Mainte_F_FM.book Page 70 Thursday, August 22, 2002 4:23 PM Troubleshooting Messages/Second messages Add Toner Cyan Description Solution The printer is out of toner (C). Replace a new toner cartridge (C). See p.1 “Replacing Consumables and Maintenance Kit”. Add Toner Magenta The printer is out of toner (M). Replace a new toner cartridge (M). See p.1 “Replacing Consumables and Maintenance Kit”. Add Toner Yellow The printer is out of toner (Y). Replace a new toner cartridge (Y). See p.
JupP1k_GB_Mainte_F_FM.book Page 71 Thursday, August 22, 2002 4:23 PM Error & Status Messages on the Control Panel Messages/Second messages Description Solution Close Right Cover The right cover is open. Close Upper Left Cover The upper left cover (the cov- Close the upper left cover. er for the fusing unit) is open. Driver Setting Error (Memory) The printer identified a down- Verify that the paper memory load error.
JupP1k_GB_Mainte_F_FM.book Page 72 Thursday, August 22, 2002 4:23 PM Troubleshooting Messages/Second messages Description Solution Hardware Problem Finisher There is a problem with the finisher. Turn the power switch off and then on. If the message appears again, contact your sales or service representative. Hardware Problem HDD The printer identified a HDD Board error. Remove and re-install the HDD Board correctly. If the message appears again, contact your sales or service representative.
JupP1k_GB_Mainte_F_FM.book Page 73 Thursday, August 22, 2002 4:23 PM Error & Status Messages on the Control Panel Messages/Second messages Description Solution Hardware Problem NV-RAM The printer identified a Mem- Replace the User Account Enory Switch (User Account En- hance Unit. hance Unit) error. Hardware Problem Option RAM The printer identified an optional RAM error. Remove and re-install the optional RAM. If the message appears again, contact your sales or service representative.
JupP1k_GB_Mainte_F_FM.book Page 74 Thursday, August 22, 2002 4:23 PM Troubleshooting Messages/Second messages Description Solution The maximum HDD area size for form/font has been exceeded. Delete the disused form /font types. An HDD overflow error occurred during Sample Print or Lacked Print. Delete the stored files or reduce the size of the Sample Print file or Lacked Print file. HDD Not Installed The user tries to print the Lacked Print data without HDD installed.
JupP1k_GB_Mainte_F_FM.book Page 75 Thursday, August 22, 2002 4:23 PM Error & Status Messages on the Control Panel Messages/Second messages Description P=07 I=9Fc01234 Power Off On Solution A controller error. The SC number indicates the prob/If Error Reoccur Call Service lem. Turn the power switch off and then on. If the message appears again, contact your sales or service representative.
JupP1k_GB_Mainte_F_FM.book Page 76 Thursday, August 22, 2002 4:23 PM Troubleshooting Messages/Second messages Remove MisfeedY: Paper Tray /See Instructions in Front Cover Description Solution There is a misfeed in the spec- Remove the misfed paper folified input tray, or the printer lowing the instructions inside is not feeding paper. the front cover. For more information, see p.96 “When "Remove Misfeed Y: Paper Tray" Appears”. Remove Misfeed: Duplex Unit There is a misfeed in the duplex unit.
JupP1k_GB_Mainte_F_FM.book Page 77 Thursday, August 22, 2002 4:23 PM Error & Status Messages on the Control Panel Messages/Second messages Replace Black PCU (Type F) Description It is time to replace the black PCU. Solution Replace a new black PCU. Depending on your service contract, contact your sales or service representative. See p.1 “Replacing Consumables and Maintenance Kit”. Replace Color Dev. Unit(TypeB) It is time to replace the color development unit. Replace a new color development unit.
JupP1k_GB_Mainte_F_FM.book Page 78 Thursday, August 22, 2002 4:23 PM Troubleshooting Messages/Second messages Description Replace Waste Toner (Type E) It is time to replace the waste toner. Solution Replace a waste toner bottle. Depending on your service contract, contact your sales or service representative. See p.1 “Replacing Consumables and Maintenance Kit”. The toner cartridge (C) is not set correctly or is not set, and the color printing is non-applicable. Set the toner cartridge (C) correctly.
JupP1k_GB_Mainte_F_FM.book Page 79 Thursday, August 22, 2002 4:23 PM Error & Status Messages on the Control Panel Messages/Second messages Reset Toner Cyan Description The indicated toner cartridge is not set correctly. Solution Set the indicated toner cartridge(s) correctly. See "Setting Up" in the Setup Guide. Reset Toner Magenta The indicated toner cartridge is not set correctly. Set the indicated toner cartridge(s) correctly. See "Setting Up" in the Setup Guide.
JupP1k_GB_Mainte_F_FM.book Page 80 Thursday, August 22, 2002 4:23 PM Troubleshooting Messages/Second messages Description SC XXX-X Power Off On 4 Solution The Service Code or SC /If Error Reoccur Call Service number indicates the problem. Turn the power switch off and then on. If the message appears again, contact your sales or service representative. Staple Cancelled The Staple feature has been cancelled.
JupP1k_GB_Mainte_F_FM.book Page 81 Thursday, August 22, 2002 4:23 PM Printer Does Not Print Printer Does Not Print Possible Cause Is the power on? Solutions Confirm that the cable is securely plugged into the power outlet and the printer. Turn on the power switch. Does the Online indicator stay on? Press {On Line} } so the indicator lights. Does the Error indicator stay red? Check the error message on the panel display and take the required action.
JupP1k_GB_Mainte_F_FM.book Page 82 Thursday, August 22, 2002 4:23 PM Troubleshooting Possible Cause Is the Data In indicator blinking or lit after starting the print job? Solutions If not blinking or lit, the data is not being sent to the printer. ❖ If the printer is connected to the computer using the interface cable Make sure the following printer port settings are correct: • For a parallel port connection, port LPT1 or LPT2 should be set.
JupP1k_GB_Mainte_F_FM.book Page 83 Thursday, August 22, 2002 4:23 PM Printer Does Not Print Possible Cause When you use 1394 Interface Unit Type1045 Solutions ❖ Network Connection Contact your network administrator. A Confirm that the 1394 Interface Unit Type1045 is attached to the computer correctly. B Confirm that the IEEE1394 interface cable is connected secure- ly. C Restart the computer. If the error occurs even after executing above operation, proceed to the following steps.
JupP1k_GB_Mainte_F_FM.book Page 84 Thursday, August 22, 2002 4:23 PM Troubleshooting Other Printing Problems Status Black gradation is not natural. Possible Causes, Descriptions, and Solutions • PCL 5c/PostScript Select "CMY+K" for Gray Reproduction in the printer driver's [Advanced] dialog box under the [Print Quality] tab. • RPCS Select "CMY+K" for Gray Reproduction under the [Image Adjustments] tab in the printer driver's [Change Use Setting] dialog box.
JupP1k_GB_Mainte_F_FM.book Page 85 Thursday, August 22, 2002 4:23 PM Other Printing Problems Status It takes too much time to complete the print job. Possible Causes, Descriptions, and Solutions Photographs and other data intensive pages take a long time for the printer to process, so simply wait when printing such data. Changing the following settings may help to speed up printing. • PCL 5c Select "600×600 dpi" for Resolution under the [Print Quality] tab in the printer driver's dialog box.
JupP1k_GB_Mainte_F_FM.book Page 86 Thursday, August 22, 2002 4:23 PM Troubleshooting Status Possible Causes, Descriptions, and Solutions Output are not delivered to the selected tray you require. When using the bypass tray, the size selected on the display panel might be different from actual paper size. Select the correct paper size. See p.47 “Paper and Other Media Supported by This Printer”.
JupP1k_GB_Mainte_F_FM.book Page 87 Thursday, August 22, 2002 4:23 PM Other Printing Problems Status The image is printed in the wrong orientation. Possible Causes, Descriptions, and Solutions The feed direction you selected and the feed direction selected in Option Setup of the printer driver might not be the same. Make the proper settings. The control panel error message Open the front cover of the printer, and then close it. stays on after removing the misfed paper. The print image is not clear.
JupP1k_GB_Mainte_F_FM.book Page 88 Thursday, August 22, 2002 4:23 PM Troubleshooting Removing Misfed Paper If a paper misfeed occurs, an error message appears indicating the location of the misfed paper on the panel display. This printer has the auto-recovery function, by which misfed paper is sent to the Standard Tray or Right Cover. Usually, you can remove the misfed paper easily with this function. B Use both hands to push it straight back in, and let go when it clicks into place.
JupP1k_GB_Mainte_F_FM.book Page 89 Thursday, August 22, 2002 4:23 PM Removing Misfed Paper C Raise the Duplex Reversal Unit slowly with both hands, and push it in until it clicks into place. Opening and Closing the Duplex Reversal Unit There are times when you might have to detach the Duplex Reversal Unit to remove misfed paper. This section describes how to detach the Duplex Reversal Unit. A Push up the lock release button and keep it in place. ZDJP205J 4 Th e D upl ex R ev er sal U n it is closed.
JupP1k_GB_Mainte_F_FM.book Page 90 Thursday, August 22, 2002 4:23 PM Troubleshooting A Turn off the power switch and unplug the power cable. B Open the front cover slowly by pulling down from the two areas on the left and right. E Pinch the upper left area of the Duplex Feed Unit, and pull it out slowly halfway. ZDJP213J 4 ZDJH007J C Take out the green screwdriver. F Holding the Duplex Feed Unit firmly with both hands, pull it straight out.
JupP1k_GB_Mainte_F_FM.book Page 91 Thursday, August 22, 2002 4:23 PM Removing Misfed Paper H Close the Duplex Feed Unit. I Holding the Duplex Feed Unit with both hands, insert it along the rails slowly until it stops. J Refasten the Duplex Feed Unit using provided screwdriver. Use the screw that was removed in step D. 4 ZDJP057J ZDJP056J The top and bottom rails are located in the position shown in the illustration.
JupP1k_GB_Mainte_F_FM.book Page 92 Thursday, August 22, 2002 4:23 PM Troubleshooting When "Remove Misfeed A:Internal Path" Appears When "Remove Misfeed B: Fusing Unit" Appears A Open the right cover. R CAUTION: • The inside of the machine becomes very hot. Do not touch the parts with a label indicating a "hot surface". Touching a "hot surface" could result in a burn. A If the 2 Tray Finisher is installed, detach it from the printer. 4 Reference ⇒ p.
JupP1k_GB_Mainte_F_FM.book Page 93 Thursday, August 22, 2002 4:23 PM Removing Misfed Paper D Pull out the upper left cover for the printer slowly. ZDJH047J E Open the upper left cover. Important ❒ Always turn the blue dial in the direction of the arrow. If you turn it in the reverse direction, the paper feeds into the printer, making it difficult for you to take out the paper. ❒ Do not pull out the misfed paper. Use the blue dial to feed misfed paper.
JupP1k_GB_Mainte_F_FM.book Page 94 Thursday, August 22, 2002 4:23 PM Troubleshooting I If the Duplex Unit is installed, close the Duplex Reversal Unit. Reference ⇒ p.89 “Opening and Closing the Duplex Reversal Unit” J If the 2 Tray Finisher was installed, reattach the 2 Tray Finisher to the printer. When "Remove Misfeed R: Finisher" Appears Open the top cover (A) and front cover (B) of the 2 Tray Finisher, and remove the misfed paper. Reference ⇒ p.
JupP1k_GB_Mainte_F_FM.book Page 95 Thursday, August 22, 2002 4:23 PM Removing Misfed Paper B Open the top cover for the 2 Tray Finisher, and pull out the misfed paper slowly. F Lower the lever slowly to return it into place. G Check areas B and C of step D. Lower the lever in the direction of the arrows (A A), and pull out the misfed paper slowly. ZDJY208J 4 C Close the top cover slowly. D Open the front cover for the 2 Tray Finisher.
JupP1k_GB_Mainte_F_FM.book Page 96 Thursday, August 22, 2002 4:23 PM Troubleshooting K Close the front cover for the 2 Tray Finisher. If the error message does not clear even after the misfed paper is removed, detach the 2 Tray Finisher from the printer to check for the misfed paper there. When "Remove Misfeed Y: Paper Tray" Appears A Open the Lower Right cover for the Paper Feed Unit, and pull out the misfed paper. Reference See p.
JupP1k_GB_Mainte_F_FM.book Page 97 Thursday, August 22, 2002 4:23 PM Removing Misfed Paper B Open the left cover for the Duplex Reversal Unit, and remove the misfed paper. Do not pull the paper out by force. E Raise the Duplex Reversal Unit slowly and insert until it clicks into place. Raise the left cover, and close it securely by pushing the area labeled "PUSH". 4 ZDJY210J If you cannot remove the paper, proceed to step C.
JupP1k_GB_Mainte_F_FM.book Page 98 Thursday, August 22, 2002 4:23 PM Troubleshooting Removing Jammed Staples When "Add Staples " appears on the panel display, or when the printer does not staple even after it is instructed to, the staples might be jammed. C Open the face plate of the cartridge to unlock it. Add Staples A Open the front cover for the 2 Tray Finisher. The stapler is attached to the position shown in the illustration. 4 ZDJP227J D Remove the jammed staples.
JupP1k_GB_Mainte_F_FM.book Page 99 Thursday, August 22, 2002 4:23 PM Removing Jammed Staples A), F Slant and insert the cartridge (A and push in until it clicks into place (B B). ZDJP218J 4 G Close the front cover for the 2 Tray Finisher.
JupP1k_GB_Mainte_F_FM.book Page 100 Thursday, August 22, 2002 4:23 PM Troubleshooting Adding Staples When "Add Staples " appears on the panel display, add a new staple refill. Add Staples C Push the areas labeled "PUSH", located on both sides of the stapler. A Open the front cover for the 2 Tray Finisher. The stapler is attached to the position shown in the illustration. 4 ZDJP222J The case cover at top floats up. D Pull the case cover up.
JupP1k_GB_Mainte_F_FM.book Page 101 Thursday, August 22, 2002 4:23 PM Adding Staples F Push in until the arrow on the refill case lines up with the arrow on the refill case cover. A), I Slant and insert the cartridge (A and push in until it clicks into place (B B). ZDJP225J G Push the case cover down until it clicks into place. ZDJP218J 4 J Close the front cover for the 2 Tray Finisher. ZDJP230J H Pull out the ribbon used for bundling the staples.
JupP1k_GB_Mainte_F_FM.book Page 102 Thursday, August 22, 2002 4:23 PM Troubleshooting Removing Punch-hole Chips When "Punch-hole Chips are Full" appears on the panel display, the punch waste box is full. Follow these steps to remove paper chips. Note ❒ Same message appears when the punch waste box is not installed correctly. Punch-hole Chips are Full 4 A Open the front cover for the 2 Tray Finisher. The punch waste box is attached to the position shown in the illustration.
JupP1k_GB_Mainte_F_FM.book Page 103 Thursday, August 22, 2002 4:23 PM 5. Appendix When the Front Cover Does Not Close When "Close Front Cover" appears on the panel display, even if the cover seems to be closed properly, it is not. C Push in the Transfer Unit until it stops. Close Front Cover When the front cover does not close, confirm that the Transfer Unit is attached firmly. The Transfer Unit is attached to the position shown in the illustration.
JupP1k_GB_Mainte_F_FM.book Page 104 Thursday, August 22, 2002 4:23 PM Appendix E Close the front cover slowly by pushing the two areas on the left and right. ZDJH041J F Plug in the power cable and turn on the power switch.
JupP1k_GB_Mainte_F_FM.book Page 105 Thursday, August 22, 2002 4:23 PM Moving and Transporting the Printer Moving and Transporting the Printer R CAUTION: • When moving the machine, each person should hold the handle, where two are located on opposite sides, and lift slowly. Lifting it carelessly or dropping it may cause an injury. • When you move the printer, remember to unplug the power cord from the wall outlet to avoid a fire or an electric shock.
JupP1k_GB_Mainte_F_FM.book Page 106 Thursday, August 22, 2002 4:23 PM Appendix D Lift the printer and move it horizontally to the place where you want to install it. Important ❒ Be sure to move the printer horizontally. Moving the printer slowly avoiding the toner to scatter. ❒ If the Paper Feed Unit(s) is installed, detach it and move the printer separately.
JupP1k_GB_Mainte_F_FM.book Page 107 Thursday, August 22, 2002 4:23 PM Consumables Consumables R CAUTION: • Our products are engineered to meet the highest standards of quality and functionality. When purchasing expendable supplies, we recommend using only those specified by an authorized dealer.
JupP1k_GB_Mainte_F_FM.book Page 108 Thursday, August 22, 2002 4:23 PM Appendix ❖ Other consumables Note ❒ Actual life of consumables depends on the type and size of paper you are using, the contents of your print images, and printing environment conditions. All that means that consumables might require replacement sooner than the life indicated. Furthermore, the life of color consumables may considerably shorten as mixed printing of black & white pages and color pages frequently occurs.
JupP1k_GB_Mainte_F_FM.
JupP1k_GB_Mainte_F_FM.
JupP1k_GB_Mainte_F_FM.
JupP1k_GB_Mainte_F_FM.
Paper type: Wood Free 80g/m2, Paper Thickness=100 µm // Pages in book=120 // Print scale=81% Gap (when printed at 81% scale) = Pages in book × Paper thickness / 2 = 6.000000 mm Introduction This manual describes detailed instructions on the operation and notes about the use of this machine. To get maximum versatility from this machine all operators are requested to read this manual carefully and follow the instructions. Please keep this manual in a handy place near the machine.
Paper type: Wood Free 80g/m2, Paper Thickness=100 µm // Pages in book=120 // Print scale=81% Gap (when printed at 81% scale) = Pages in book × Paper thickness / 2 = 6.000000 mm RICOH COMPANY, LTD. 15-5, Minami Aoyama 1-chome, Minato-ku, Tokyo 107-8544, Japan Phone: +81-(0)3-3479-3111 The Netherlands RICOH EUROPE B.V. Groenelaan 3, 1186 AA, Amstelveen Phone: +31-(0)20-5474111 Italy RICOH ITALIA SpA Via della Metallurgia 12, 37139 Verona Phone: +39-045-8181500 United Kingdom RICOH UK LTD.
