Operating Instructions Copy Reference 1 Placing Originals 2 Copying 3 Appendix Read this manual carefully before you use this machine and keep it handy for future reference. For safe and correct use, be sure to read the Safety Information in "About This Machine" before using the machine.
Introduction This manual contains detailed instructions and notes on the operation and use of this machine. For your safety and benefit, read this manual carefully before using the machine. Keep this manual in a handy place for quick reference. Important Contents of this manual are subject to change without prior notice. In no event will the company be liable for direct, indirect, special, incidental, or consequential damages as a result of handling or operating the machine.
Manuals for This Machine Refer to the manuals that are relevant to what you want to do with the machine. Important ❒ Media differ according to manual. ❒ The printed and electronic versions of a manual have the same contents. ❒ Adobe Acrobat Reader/Adobe Reader must be installed in order to view the manuals as PDF files. ❒ Depending on which country you are in, there may also be html manuals. To view these manuals, a Web browser must be installed.
❖ Network Guide Explains how to configure and operate the machine in a network environment, and use the software provided. This manual covers all models, and includes descriptions of functions and settings that might not be available on this machine. Images, illustrations, and information about operating systems that are supported might also differ slightly from those of this machine.
What You Can Do with This Machine Available functions differ depending on the model and options. Reference p.2 “Functions Requiring Optional Configurations” Types of Duplex Copies ❖ 1 Sided 2 Pages → 2 Sided 1 Page See p.47 “Duplex (Type 2 only)”. ❖ 2 Sided 1 Page → 2 Sided 1 Page See p.47 “Duplex (Type 2 only)”. ❖ 1 Sided 4 Pages → Combine 2 Sided 1 Page See p.53 “Two-Sided Combine (Type 2 only)”.
❖ 1 Sided 8 Pages → Combine 2 Sided 1 Page See p.53 “Two-Sided Combine (Type 2 only)”. GCSHVYAE 1 Front 2 Back ❖ 2 Sided 2 Pages → Combine 2 Sided 1 Page See p.53 “Two-Sided Combine (Type 2 only)”. GCSHVY1E ❖ 2 Sided 4 Pages → Combine 2 Sided 1 Page See p.53 “Two-Sided Combine (Type 2 only)”.
Combining Multiple Pages onto a Single Page See p.50 “One-Sided Combine”.
❖ 2 Sided 2 Pages → Combine 1 Sided 1 Page GCSHVYBJ Copying Originals Such as Books See p.56 “Series Copies”. ❖ Bound Originals → 1 Sided 2 Pages CP2B0100 ❖ 2 Sided 1 Page → 1 Sided 2 Pages Copying onto Envelopes ❖ Envelope See p.32 “When Copying onto Envelopes”.
TABLE OF CONTENTS Manuals for This Machine ......................................................................................i What You Can Do with This Machine..................................................................iii Types of Duplex Copies ............................................................................................ iii Combining Multiple Pages onto a Single Page .......................................................... v Copying Originals Such as Books......................
3. Appendix Combination Chart...............................................................................................59 Supplementary Information ................................................................................60 INDEX.........................................................................................................
How to Read This Manual Note ❒ For proper use of this product, be sure to read About This Machine first. ❒ Supplementary information about the copier mode is described in “Supplementary Information”. Reference p.60 “Supplementary Information” Symbols This manual uses the following symbols: Indicates important safety notes. Ignoring these notes could result in serious injury or death. Be sure to read these notes. They can be found in the “Safety Information” section of About This Machine.
Functions Requiring Optional Configurations Certain functions require special machine configuration and extra options. See the table below.
Display This section explains how to read the display and how to use the selection keys on the copy display. Note ❒ The copy display is set as the default screen when the machine is turned on. Reading the Display ❖ Initial copy display AAX024S AAI024S 1. Displays operational status and messages. 2. Displays the current paper tray and selected items that appear in brackets. 3. Displays the number of copies set. 4. Displays frequently used functions.
Using the Keys on the Control Panel ARB039S 4 1. Selection keys 2. {Escape} key Correspond to items at the bottom line on the display. Example: initial copy display Press to cancel an operation or return to the previous display. • When the instruction “press [100%]” appears in this manual, press the left selection key. • When the instruction “press [R/E]” appears in this manual, press the center selection key.
User Tools Menu (Copier Features) This section describes items you can set in the copier feature. The copier features screen can be displayed by pressing the {User Tools/Counter} key. For details about how to set up these items, see General Settings Guide. Item Description APS/ Auto R/E Priority You can select [Auto Paper Select Priority] (APS Priority) or [Auto R/E Priority] (Auto Reduce/Enlarge Priority).
6
1. Placing Originals This chapter describes the types of originals you can set and how to place originals. Originals This section describes the types of originals that can be placed, paper sizes that are automatically detected, and missing image area. Sizes and Weights of Recommended Originals The following describes recommended paper sizes and weights, and non-recommended originals for the ADF or ARDF.
Placing Originals Non-compatible originals for the ADF or ARDF Placing the following types of originals in the ADF or ARDF can cause paper misfeeds or light and black lines, or result in damage to the originals. Place these originals on the exposure glass instead.
Originals Sizes Detectable by Auto Paper Select Sizes detectable from the exposure glass, and ADF or ARDF are: 1 ❖ Metric version Size A3L Location of the original B4 JIS *1 L A4KL B5 JIS *1 L B5 JIS *1 K A5KL × Exposure glass 81/2" × 13" L × *2 ADF / ARDF : Detectable × : Undetectable *1 *2 JIS: Japanese Industrial Standard If you want to make A5K paper detectable, contact your service representative.
Placing Originals Maximum scanning area ❖ Exposure glass 1 CP01AEE ❖ ADF or ARDF ARB051S Note ❒ When you copy custom size originals, make sure you specify the size of the originals. If not, the image may not be copied properly. Reference p.16 “Specifying the Original Size When a Paper Tray is Selected” p.18 “Specifying the Original Size When the Bypass Tray is Selected” Sizes difficult to detect It is difficult for the machine to detect the sizes of the following originals.
Originals Missing Image Area Even if you correctly place originals in the ADF or ARDF, or on the exposure glass, margins of a few millimeters on all four sides of the original might not be copied. 1 GCGENK2E 1 0.5 mm (0.02") or more 2 0.5 mm (0.02") or more 3 2 ± 1.5 mm (0.08" ± 0.06") 4 2 ± 1.5 mm (0.08" ± 0.
Placing Originals Placing Originals This section describes the procedure for placing originals on the exposure glass and in the ADF or ARDF. Take care to place originals after any correction fluid and ink has completely dried. Not taking this precaution could cause marks on the exposure glass that will be copied onto paper. 1 Reference p.7 “Originals” Original Orientation You can set the original orientation in the following ways.
Placing Originals Placing Originals on the Exposure Glass Place originals on the exposure glass. 1 Important ❒ Do not lift the exposure glass cover, ADF, or ARDF forcefully. Otherwise, it will be damaged, or the cover of the ADF or ARDF might open. A Lift the exposure glass cover, ADF, or ARDF. Be sure to lift the exposure glass cover, ADF, or ARDF by more than 30 degrees. Otherwise, the size of the original might not be detected correctly. B Place the original face down on the exposure glass.
Placing Originals Placing Originals in the ADF or ARDF Place originals in the ADF or ARDF. Settings should be made when placing custom size originals. 1 ❖ When placing custom size originals: See p.16 “Specifying the Original Size When a Paper Tray is Selected” and p.18 “Specifying the Original Size When the Bypass Tray is Selected”.
Placing Originals A Adjust the document guide to the original size. B Set the aligned originals face up into the ADF or ARDF. Do not stack originals beyond the limit mark. The first page should be on the top. Be sure not to block the sensor or load the original untidily. Doing so may cause the machine to detect the size of the scanned image incorrectly or display a paper misfeed message. Also, be sure not to place originals or other objects on the top cover. Doing so may cause a malfunction.
Placing Originals Specifying the Original Size When a Paper Tray is Selected You can select either regular or custom for the size of the original when a paper tray is selected. 1 Regular sizes When placing regular size originals on the exposure glass, or in the ADF or ARDF, select the size of the originals from the regular sizes shown on the display. A Select a desired paper tray using {U} or {T}. B Press the {q} key. C Select [Regular Size] using {U} or {T}, and then press the {OK} key.
Placing Originals Custom sizes When placing custom size originals on the exposure glass, or in the ADF or ARDF, specify the size of the originals using the number keys. 1 Important ❒ Originals that have a vertical length of 105–297 mm (4.2"-11.6") and a horizontal length of 128-1,260 mm (5.1"-49.6") can be specified. A Select a desired paper tray using {U} or {T}. B Press the {q} key. C Select [Custom Size] using {U} or {T}, and then press the {OK} key.
Placing Originals E Enter the vertical size of the original (Vert.) with the number keys, and then press the {OK} key. 1 The “Programmed” message appears. When the custom size originals settings are registered, on the top of the copy display. appears Note ❒ This function is not available in Auto Paper Select mode. ❒ If you make a mistake in step D or E, press the {Clear/Stop} key, and then enter the value again. ❒ To cancel the size you have set, press the {Clear Modes} key.
Placing Originals C Select [Original Size] using {U} or {T}, and then press the {OK} key. 1 D Select [Regular Size] using {U} or {T}, and then press the {OK} key. When [Auto Detect] is selected, the size of the placed original will be detected automatically. E Select the original size using the scroll keys, and then press the {OK} key. The “Programmed” message appears. When the regular size originals settings are registered, on the top of the copy display.
Placing Originals Custom sizes When placing custom size originals on the exposure glass, or in the ADF or ARDF, specify the size of the originals using the number keys. 1 Important ❒ Originals that have a vertical length of 105–297 mm (4.2"-11.6") and a horizontal length of 128-1,260 mm (5.1"-49.6") can be specified. A Select [Bypass] using {U} or {T}. B Press the {q} key. C Select [Original Size] using {U} or {T}, and then press the {OK} key.
Placing Originals F Enter the vertical size of the original (Vert.) with the number keys, and then press the {OK} key. 1 The “Programmed” message appears. When the custom size originals settings are registered, on the top of the copy display. appears Note ❒ This function is not available in Auto Paper Select mode. ❒ If you make a mistake in step E or F, press the {Clear/Stop} key, and then enter the value again. ❒ To cancel the size you have set, press the {Clear Modes} key.
Placing Originals 1 22
2. Copying This chapter describes procedures for making copies in various modes. Basic Procedure This section describes the basic procedure for making copies. Important ❒ When User Code Authentication is set, enter your user code (up to eight digits) with the number keys so that the machine accepts copy jobs. See “Authentication Information”, General Settings Guide.
Copying F Press the {Start} key. 2 ARB033S The machine starts copying. When placing originals on the exposure glass, press the {q} key after all originals are scanned. Copies are delivered face down. Note ❒ Always log off when you have finished using the machine to prevent unauthorized users from using the machine. ❒ To stop the machine during a multicopy run, press the {Clear/Stop} key. ❒ To return the machine to its initial state after copying, press the {Clear Modes} key.
Copying from the Bypass Tray Copying from the Bypass Tray Use the bypass tray to copy onto OHP transparencies, thick paper, envelopes, and paper that cannot be loaded in the paper trays. Important ❒ Paper that has a vertical length of 90-297 mm (3.55"-11.69") and a horizontal length of 148-600 mm (5.83"-23.62") can be copied from the bypass tray. However, when paper larger than 433 mm (17.1") in size is used, the paper may become wrinkled, may not be fed into the machine, or may cause paper jams.
Copying B Push up the paper guide release lever. 2 ARB017S 1 Paper guide release lever C Insert the paper face down, and then align the paper guides to the paper size. If the guides are not flush against the paper, images might be skewed or paper misfeeds might occur. Swing out the extender to support paper sizes larger than A4L or 81/2" × 11"L. To prevent multiple sheets from being fed at once, fan paper before placing it on the tray.
Copying from the Bypass Tray D Pull down the paper guide release lever. 2 ARB019S 1 Paper guide release lever The bypass tray is selected on the display. E Select the size and type of the paper, if required. Note ❒ If [Bypass] is not selected on the display in step D, select [Bypass] using {U} or {T}, and then press the {q} key. When Copying onto Regular Size Paper Makes copies onto regular size paper from the bypass tray. A Select [Bypass] using {U} or {T}. B Load paper face down on the bypass tray.
Copying E Select [Regular Size] using {U} or {T}, and then press the {OK} key. F Select the paper size using the scroll keys, and then press the {OK} key. 2 The “Programmed” message appears. G Place the originals, and then press the {Start} key. H When the copy job is finished, press the {Clear Modes} key to clear the settings. Reference p.25 “Loading Paper on the Bypass Tray” When Copying onto Custom Size Paper Makes copies onto custom size paper from the bypass tray.
Copying from the Bypass Tray F Enter the horizontal size of the paper (Horiz.) with the number keys, and then press the {OK} key. 2 G Enter the vertical size of the paper (Vert.) with the number keys, and then press the {OK} key. The “Programmed” message appears. H Place the originals, and then press the {Start} key. I When the copy job is finished, press the {Clear Modes} key to clear the settings. Note ❒ If you make a mistake in step F or G, press the {Clear/Stop} key, and then enter the value again.
Copying D Select [Paper Type] using {U} or {T}, and then press the {OK} key. E Select [OHP (Transparency)] using {U} or {T}, and then press the {OK} key. 2 The “Programmed” message appears. F Select the paper size, if required. G Place the originals, and then press the {Start} key. H When the copy job is finished, press the {Clear Modes} key to clear the settings. Note ❒ Printing on OHP transparencies is slower than printing on plain paper. Reference p.
Copying from the Bypass Tray D Select [Paper Type] using {U} or {T}, and then press the {OK} key. E Select [Thick Paper] using {U} or {T}, and then press the {OK} key. 2 The “Programmed” message appears. F Select the paper size, if required. G Place the originals, and then press the {Start} key. H When the copy job is finished, press the {Clear Modes} key to clear the settings. Note ❒ Printing on thick paper is slower than printing on plain paper. Reference p.
Copying When Copying onto Envelopes When copying onto envelopes, select the envelope size in Paper Size, and [Thick Paper] in Paper Type. Important ❒ Before loading envelopes, use a pen or similar to flatten their edges.
Copying from the Bypass Tray ❖ Printable area The following areas of envelopes can be printed on: 2 ARB024S 1 Feeding direction 2 Printable area 3 20 mm (0.79") 4 10 mm (0.40") 5 5 mm (0.20") ❖ Orientation of Originals and Envelopes Originals and envelopes must be placed in the same orientation. To minimize waste and time, check that originals and envelopes are loaded in the same orientation. ARB025S The illustration shows the orientation of originals and envelopes.
Copying A Select [Bypass] using {U} or {T}. B Load envelopes face down on the bypass tray. 2 ARB020S 1 Paper guide release lever C Press the {q} key. D Select [Paper Size] using {U} or {T}, and then press the {OK} key. E Select [Regular Size] using {U} or {T}, and then press the {OK} key. F Select the envelope size using {U} or {T}, and then press the {OK} key. The “Programmed” message appears. G Press the {q} key.
Copying from the Bypass Tray H Select [Paper Type] using {U} or {T}, and then press the {OK} key. I Select [Thick Paper] using {U} or {T}, and then press the {OK} key. 2 The “Programmed” message appears. J Place the original, and then press the {Start} key. K When the copy job is finished, press the {Clear Modes} key to clear the settings. Reference p.
Copying Copy Functions Adjusting Image Density You can adjust the image density in five levels. If you want darker or lighter copies, adjust the image density accordingly. 2 A Press the {Lighter} or {Darker} key to adjust the image density. The density indicator “ ” moves.
Copy Functions Original Type Setting Select one of the following original types to match your originals: ❖ Text Select this mode when your originals contain only text (no pictures). ❖ Photo Delicate tones of photographs and pictures can be reproduced with this mode. • When copying developed photographs • When copying photographs or pictures that are printed on paper (e.g. magazines) • When copying originals generated by color copiers 2 A Press the {Original Type} key to select the original type.
Copying Selecting Copy Paper There are two ways to select paper: ❖ Auto Paper Select The machine selects a suitable size of paper automatically based on the original size and reproduction ratio. 2 ❖ Manual Paper Select Choose a tray containing the paper you want to copy onto: the paper trays or the bypass tray. See the following table for paper sizes and orientations that can be used with Auto Paper Select (when copying at a ratio of 100%).
Copy Functions Auto Paper Select The machine selects a suitable size of paper automatically based on the original size and the reproduction ratio. A Make sure that [Auto Paper Select] is selected. 2 Note ❒ If [Auto Paper Select] is not selected, select [Auto Paper Select] by using {U} or {T}. ❒ Paper placed in the bypass tray will not be selected with Auto Paper Select. Manual Paper Select Choose a tray containing the paper you want to copy onto: the paper trays or the bypass tray.
Copying Note ❒ This function works when Auto Paper Select or Auto Reduce/Enlarge is selected. ❒ The default setting for Auto Tray Switching is [On]. You cannot use the Rotated Copy function if this setting is changed to [Off]. ❒ You cannot use the Rotated Copy function when enlarging onto A3 or B4 JIS, or 11" × 17" or 81/2" × 14" size paper. In this case, place your original in the L orientation.
Copy Functions ❖ Base Point The base point of Reduce/Enlarge differs depending on how the original is scanned. When the original is set on the exposure glass, the upper left corner will be the base point. When it is set in the ADF or ARDF, the bottom left corner of the original will be the base point. The figure below is the resulting copy images that differ depending on how the original is scanned.
Copying Zoom You can change the reproduction ratio in increments of 1%. 2 Selecting a ratio using the scroll keys Select a ratio using {U} or {T}. A Press [R/E]. B Select a preset ratio which is close to the desired ratio with [Enlarge] or [Reduce] and then press [Zoom]. C Specify a ratio using {U} or {T}, and then press the {OK} key. Pressing {U} or {T} changes the ratio in increments of 1%. Pressing and holding down the relevant key changes the ratio in increments of 10%.
Copy Functions Note ❒ If you make a mistake in step C, readjust it using {U} or {T}. Entering a ratio with the number keys Select a ratio using the number keys. A Press [R/E]. 2 B Press [Zoom]. C Enter the desired ratio with the number keys, and then press the {OK} key. The “Programmed” message appears. D Place the original, and then press the {Start} key. Note ❒ If you make a mistake in step C, press the {Clear/Stop} key, and then enter the value again.
Copying Auto Reduce/Enlarge The machine automatically selects an appropriate reproduction ratio based on the paper and original sizes you select. 2 Important ❒ You cannot use the bypass tray with this function.
Copy Functions B Select the paper size using {U} or {T}. C Place the originals, and then press the {Start} key. 2 The machine automatically selects an appropriate ratio and then begins copying. Reference p.10 “Sizes difficult to detect” Sort The machine assembles copies as sets in sequential order. Important ❒ To use the Rotate Sort function, two paper trays loaded with paper of the same size and type, but in different orientation (KL), are required. See “Paper Type: Tray 1-4”, General Settings Guide.
Copying A Press the {Sort} key. 2 ARB047S The indicator goes on. B Select [Sort] or [Rotate Sort] using {U} or {T}, and then press the {OK} key. The “Programmed” message appears. C Enter the number of copy sets using the number keys. D Place the originals. When placing originals on the exposure glass, start with the first page to be copied. When placing originals in the ADF or ARDF, set the first page on the top. E Press the {Start} key.
Copy Functions Changing the number of sets You can change the number of copy sets during copying. Important ❒ This function can only be used when the Sort function is turned on. A While "Copying..." is displayed, press the {Clear/Stop} key. B Press [Sets]. 2 C Enter the number of copy sets with the number keys, and then press [Resume]. Copying starts again. Note ❒ The number of sets you can enter in step C differs depending on when the {Clear/Stop} key is pressed.
Copying ❖ 2 Sided → 2 Sided Copies 1 two-sided page to 1 two-sided page. 2 Note ❒ An optional ARDF is required to scan two-sided originals. Original orientation and completed copies The resulting copy image will differ according to the orientation in which you place the originals (vertical K or horizontal L). The table shows the orientation of images on the front and back of copies, not the orientation of delivery.
Copy Functions A Press the {Duplex} key. 2 ARB048S The indicator goes on. B Select the duplex mode using {U} or {T}, and then press the {OK} key. C Select the original orientation using {U} or {T}, and then press the {OK} key. D Select the duplex orientation using {U} or {T}, and then press the {OK} key. The “Programmed” message appears. E Place the originals. When placing originals on the exposure glass, start with the first page to be copied.
Copying Note ❒ The paper weight that can be used with duplex copying is 64-90 g/m2 (20-24 lb.) ❒ To cancel the Duplex function in step A, press the {Duplex} key again. Make sure the indicator goes off. ❒ To display the screens in steps C and D , select [Always Specify] for [Orientation] with Copier Features in User Tools. If [Do not Specify] is selected, proceed to step E. ❒ You can change the margins of duplex copies.
Copy Functions ❖ 2 Sided 1 Page → Combine 1 Side Copies 1 two-sided original to one side of a sheet. 2 GCSHVYOJ ❖ 2 Sided 2 Pages → Combine 1 Side Copies 2 two-sided originals to one side of a sheet. GCSHVYBJ Note ❒ An optional ARDF is required to scan two-sided originals.
Copying Placing originals (originals placed in the ADF or ARDF) • Originals read from left to right Combine5 2 • Originals read from top to bottom Combine6 A Press the {Combine/Series} key. ARB049S The indicator goes on. B Select the combine mode using {U} or {T}, and then press the {OK} key. C Select the original orientation using {U} or {T}, and then press the {OK} key. The “Programmed” message appears.
Copy Functions D Select the paper size using {U} or {T}, and then press the {OK} key. E Place the originals, and then press the {Start} key. 2 Note ❒ To cancel the One-Sided Combine function in step A, press the {Combine/Series} key again. Make sure the indicator goes off. ❒ To display the screen in step C, select [Always Specify] for [Orientation] with Copier Features in User Tools. If [Do not Specify] is selected, proceed to step D.
Copying ❖ 1 Sided 8 Pages → Combine 2 Sides Copies 8 one-sided originals to one sheet with four pages per side. 2 GCSHVYAE 1 Front 2 Back ❖ 2 Sided 2 Pages → Combine 2 Sides Copies 2 two-sided originals to one sheet with two pages per side. GCSHVY1E ❖ 2 Sided 4 Pages → Combine 2 Sides Copies 4 two-sided originals to one sheet with four pages per side.
Copy Functions A Press the {Combine/Series} key. 2 ARB049S The indicator goes on. B Select the combine mode using {U} or {T}, and then press the {OK} key. C Select the original orientation using {U} or {T}, and then press the {OK} key. D Select the duplex orientation using {U} or {T}, and then press the {OK} key. The “Programmed” message appears. E Select the paper size using {U} or {T}, and then press the {OK} key. F Place the originals, and then press the {Start} key.
Copying Note ❒ An optional ARDF is required to scan 2-sided originals. ❒ To cancel the Two-Sided Combine function in step A, press the {Combine/Series} key again. Make sure the indicator goes off. ❒ To display the screens in steps C and D, select [Always Specify] for [Orientation] with Copier Features in User Tools. If [Do not Specify] is selected, proceed to step E.
Copy Functions ❖ Book → 1 Sided Copies two facing pages of a bound original (book) to two separate pages. 2 CP2B0100 ❖ 2 Sided→1 Sided Copies each side of a two-sided original to two separate pages. A Press the {Combine/Series} key. ARB049S The indicator goes on. B Select [Series: Book Orig.] or [Series:2Sided Orig.] using {U} or {T}, and then press the {OK} key. When selecting [Series: Book Orig.], proceed to step D.
Copying C Select the original orientation using {U} or {T}, and then press the {OK} key. 2 The “Programmed” message appears. Proceed to step E. D Select the paper size using {U} or {T}, and then press the {OK} key. E Place the originals, and then press the {Start} key. Note ❒ An optional ARDF is required to scan 2-sided originals. ❒ To cancel the Series Copies function in step A, press the {Combine/Series} key again. Make sure the indicator goes off.
3. Appendix This chapter describes the copy machine's specifications and the function compatibility. Combination Chart The combination chart given below shows which modes can be used together. Blank : These modes can be used together. × : These modes cannot be used together. The first mode selected will be the mode you are working in. : These modes cannot be used together. The second mode selected will be the mode you are working in. The following shows the combinations of functions.
Appendix Supplementary Information The following describes the detailed specifications of the respective functions. ❖ Bypass Tray Copy • The following paper sizes can be selected.
Supplementary Information ❖ Inch version Ratio (%) Original → Paper size 200 (enlarge area by 4) 51/2" × 81/2" → 11" × 17" 155 *1 (enlarge area by 2) 51/2" × 81/2" → 81/2" × 14" 129 *1 81/2" × 11" → 11" × 17" 121 *1 81/2" × 14" → 11" × 17" 93 *1 -- 85 8" × 13" → 81/2" × 11" 78 *1 81/2" × 14" → 81/2" × 11" 73 11" × 15" → 81/2" × 11" 65 *1 11" × 17" → 81/2" × 11" 50 *1 (reduce area by 1/4) 11" × 17" → 51/2" × 81/2" *1 3 Default settings • You can select a ratio regardless of the size
Appendix ❖ Duplex (Type 2 only) • The following paper sizes and orientations can be duplexed. A3L, B4 JISL, A4KL, B5 JISKL, A5KL, 11" × 17"L, 81/2" × 14"L, 81/2" × 13"L, 81/2" × 11"KL, 81/4" × 14"L, 81/4" × 13"L, 8" × 13"L, 71/4" × 101/2"KL, 8KL, 16KKL • You cannot use the following paper with this function: • Paper smaller than A5 (71/4" × 101/2") • Paper thicker than 90 g/m2 (24 lb.) • Paper thinner than 64 g/m2 (17 lb.
INDEX 1 Sided 2 Pages to Combine 1 Side, 50 1 Sided 4 Pages to Combine 1 Side, 50 1 Sided 4 Pages to Combine 2 Sides, 53 1 Sided 8 Pages to Combine 2 Sides, 53 1 Sided to 2 Sided, 47 2 Sided 1 Page to Combine 1 Side, 50 2 Sided 2 Pages to Combine 1 Side, 50 2 Sided 2 Pages to Combine 2 Sides, 53 2 Sided 4 Pages to Combine 2 Sides, 53 2 Sided to 1 Sided, 56 2 Sided to 2 Sided, 47 A ADF, 1, 9, 14 Adjusting Image Density, 36 APS/ Auto R/E Priority, 5 ARDF, 1, 2, 9, 14 Auto Document Feeder, 1 Auto Paper Select
M Manual Paper Select, 38, 39 Maximum scanning area, 9 Max.
In accordance with IEC 60417, this machine uses the following symbols for the main power switch: a means POWER ON. c means STAND BY. Trademarks Acrobat® is a registered trademark of Adobe Systems Incorporated. Other product names used herein are for identification purposes only and might be trademarks of their respective companies. We disclaim any and all rights to those marks.
Operating Instructions Copy Reference Type for 9016/DSm716/LD316/Aficio MP 1600 Type for 9021d/DSm721d/LD320d/Aficio MP 2000 EN USA B843-7550
