Installation manual

Configuration/Dealer Settings 23
Auto
adjusting
Spec
Min Max
0000: 3.46 4.00
0001: 3.00 3.46
0010: 2.59 3.00
0011: 2.25 2.59
Spec Min Max
0100: 1.95 2.25
0101: 1.69 1.95
0110: 1.46 1.69
0111: 1.27 1.46
Spec Min Max
1000: 1.09 1.27
1001: 0.95 1.09
1010: 0.82 0.95
1011: 0.71 0.82
Spec Min Max
1100: 0.61 0.71
1101: 0.53 0.91
1110: 0.46 0.53
1111: 0.40 0.46
32 1010 Calibration/Default
Spec/Spec 142
Mode Protected by
Span
0: Yes
1: No
Low Battery (turn on
annunciator)
0: Yes
1: No
Auto Exit from Part
Accumulation and
Reduction Mode
0: No
1: Yes
Scale Connected to
the Cable Port 2
Connector
0: No
1: Yes
CAUTION: If you are
not connecting a scale
to this connector,
make sure that you
select No. Selecting
Yes can damage the
console’s electronic
components.
33 0____ Over Weight Mask
at:
0: +1d
1: +9d
Weight Decimal Point Position (Cable Port 2, Scale 2 or 3)
000: 00000 011: 00.000
001: 0000.0 100: 0.0000
010: 000.00
34 0000 (For Scale 1)
0: For std/normal load
cell
1: For abnormal load
cell with too large
offset
A/D Board (Scale 1) Vibration Sensitivity
Settings
00: Normal
01: Prevent from small vibration/fast change in
display
10: Prevent from medium vibration
11: Prevent from large slow change in display
35 0000 (For Scale 2)
0: For std/normal load
cell
1: For abnormal load
cell with too large
offset
A/D Board (Scale 2) Vibration Sensitivity
Settings
00: Normal
01: Prevent from small vibration/fast change in
display
10: Prevent from medium vibration
11: Prevent from large slow change in display
36 __00 Minimum Display (Cable Port 2, Scale 2 or 3)
00: 2 01: 1
10: 5 11: 10
A/D Board (Cable Port 2, Scale 2 or 3) Vibration
Sensitivity Settings
00: Normal
01: Prevent from small vibration/fast change in
display
10: Prevent from medium vibration
11: Prevent from large slow change in display
37 1001 Load Cell Sensitivities Selection (mV/V)—Cable Port 2, Scale 2 or 3
Spec
Min Max
0000: 3.46 4.00
0001: 3.00 3.46
0010: 2.59 3.00
0011: 2.25 2.59
Spec
Min Max
0100: 1.95 2.25
0101: 1.69 1.95
0110: 1.46 1.69
0111: 1.27 1.46
Spec
Min Max
1000: 1.09 1.27
1001: 0.95 1.09
1010: 0.82 0.95
1011: 0.71 0.82
Spec
Min Max
1100: 0.61 0.71
1101: 0.53 0.91
1110: 0.46 0.53
1111: 0.40 0.46
Specification Default Bit 3 Bit 2 Bit 1 Bit 0
Table 5-2. Applicable IQ9500 Weight and Measurement Specifications (142 Settings) (Continued)