SWII Users Manual Intercomp Co. 3839 County Road 116 Minneapolis, MN 55340 (763)-476-2531 1-800-328-3336 Fax 763-476-2613 www.intercompracing.
SWII Users Rev I, May 2009 Table of Contents INTRODUCTION .......................................................................................................................................................3 SPECIFICATIONS .........................................................................................................................................................3 Controls..........................................................................................................................
SWII Users Rev I, May 2009 Introduction This manual contains specifications and operating instructions for Intercomp's SWII Scale System. Specifications Controls General: Channel selection: Display: Indicators: On, Off, %/WGT, TEST/ZERO, Left Front, Right Front, Left Rear, Right Rear Any combination 4 digit, LCD (0.
SWII Users Rev I, May 2009 Physical 4” heavy duty Weigh Pad Dimensions: Weight: Leveling: 4” Weigh Pad Dimensions: Weight: Leveling: 2” Weigh Pad Dimensions: Weight: Weight: Indicator 15” x 15” x 4” per pad 35 lb / 15.9 kg adjustable feet for leveling on uneven surfaces 15” x 15” x 4” per pad 35 lb / 15.9 kg adjustable feet for leveling on uneven surfaces 15” x 15” x 2” per pad 23 lb / 10.
SWII Users Rev I, May 2009 Setup System System setup configuration 1. Place the four pads near their appropriate car tire: LF by left front, RF by right front and so on. 2. Connect one end of each cable to a pad: LF-Red cable, RF-Green cable, LR-White cable, RR-Black cable. 3. Connect the free end of each cable to the control box: LF-Red cable, RF-Green cable, LR-White cable, RR-Black cable. 4. Turn the indicator on. 5. Jack the car onto each pad. .
SWII Users Rev I, May 2009 Operations Display Left Front Low Battery Right Front 8888 Left Rear Selected % Right Rear Controls ON Turns system on. OFF Turns system off.
SWII Users Rev I, May 2009 % / WGT When pressed the display will show the selected weight percentage and the % indicator will be “on”. This value is the weight percentage of the selected pads vs. the total weight of the car. If a specific pad indicator is “on” it means that weight is selected and will be added into the total and percentage shown. A percentage will be displayed if no wheel weights are negative and the total weight is not zero.
SWII Users Rev I, May 2009 FRONT TOTAL By pressing LEFT FRONT and RIGHT FRONT simultaneously, the weight of the front end is displayed. REAR TOTAL By pressing LEFT REAR and RIGHT REAR simultaneously, the weight of the rear end is displayed. CROSS By pressing LEFT REAR and RIGHT FRONT or LEFT FRONT and RIGHT REAR simultaneously, the cross weight is displayed. TOTAL By pressing all pad select keys together, the total weight of the car is displayed.
SWII Users Rev I, May 2009 Serial Output Connector Pin Designations: PT Connector A: NC B: NC C: Ground (- Charging Voltage) D: NC E: +Charging Voltage F: NC G: TXD H: Ground (signal) Protocol The serial output is RS-232 and in the following format: 1200 Baud 8 data bits 1 start bit 2 stop bits no parity Page 9 of 11
SWII Users Rev I, May 2009 Error messages dise OE Eepe The weight is too large to fit on the display. This message will blink if weight present on the pad exceeds the pads capacity, or the pad is not plugged in, or the pad may have failed. EEPROM error. The scale has lost saved information or its calibration information was corrupted. Scale will require calibration.
SWII Users Rev I, May 2009 How to reach Intercomp Service Things to know: 1. 2. 3. 4. The service is for a SWII scale system. When did you purchase your scale? What is your serial number? Whom did you purchase the scale through? For Intercomp Service call or fax: FAX # (763)-476-2613 (763)-476-2531 1-800-328-3336 or fill out Service Support form at: www.intercompcompany.
