CS200 Users Manual Intercomp Co. 3839 County Road 116 Medina, MN 55340 U.S.A. (763)-476-2531 1-800-328-3336 Fax: 763-476-2613 www.intercompcompany.
CS200, Users August, 2009 Table of Contents INTRODUCTION .......................................................................................................................................................3 SPECIFICATIONS .....................................................................................................................................................3 CONTROLS ..............................................................................................................................
CS200, Users August, 2009 Introduction This manual contains specifications and operation instructions for Intercomp's model CS200 Crane Scale. Specifications Controls General: Display: Zero, backlight, On/Off. 4 digit LCD. Electrical Batteries: Resolution: Auto-Zero: Battery life: Low battery indication: 1 (9-volt) size disposable alkaline or rechargeable NickelCadmium cell. 14 bit A/D delivers over 16,000 internal counts.. Automatically zeros off errors of zero-load.
CS200, Users August, 2009 Operations Operating Practices Warning: The crane scale will be operated by qualified designated persons, trainees under the direct supervision of designated persons, maintenance and test personnel when in performance of their assigned duties, or lifting device inspectors. Warning: Do not exceed the rated load limit of the crane scale. Warning: The crane scale shall be applied to the load in accordance with the instruction manual.
CS200, Users August, 2009 Warning: Stay clear of suspended loads. Warning: Do not lift loads higher than necessary. Warning: Do not make alterations or modifications to the crane scale. Warning: Ensure all portions of the human body are kept clear of all device involved with the rigging during the lift. Controls On/Off Press this button to turn the CS200 on. The unit tests itself; when these tests have completed successfully, the system begins weighing. Press this button again to turn the unit off.
CS200, Users August, 2009 Units Switching (lb and kg) The CS200 can toggle between lb and kg. To switch units simultaneously press and hold the ZERO and backlight keys. After pressing and holding these keys for a few seconds, the unit will momentarily display: 1) “kgS kgS”, kgS if you have now switched to display in kgs. 2) “lbS lbS”, lbS if you have now switched to display in lbs.
CS200, Users August, 2009 To adjust the sample rate: Access the options menu. Press ZERO until the display reads “S S rt”. rt Simultaneously press the ZERO and backlight keys and release. Enter the sample rate. The display will momentarily display “SavE SavE” SavE and return to normal mode. Sleep The sleep mode is designed to conserve battery life. The sleep mode time is how long the scale's display will remain ON without any activity (a key being pressed or a change in weight).
CS200, Users August, 2009 Maintenance Periodic Inspection The crane scale and all associated adaptive devices require periodic inspection and maintenance. The frequency and recording of the inspection requirements are found in service categories below and are dependant on the type of service that the equipment is used in as described below. Service Categories Normal Service – Crane scale is operated at less than 85% of it’s capacity except for isolated instances.
CS200, Users August, 2009 3. Inspect for excessive wear of linkages and other mechanical parts. 4. Inspect for excessive wear at hoist hooking points and load support clevices or pins. 5. Inspect for any visible bends or twists of all used rigging devices. 6.
CS200, Users August, 2009 10% through 100% of the scales capacity. Press the ON switch. The display does a lamp test; during this time the scale does a quick check of itself. Then the weighing system starts weigh mode. Intercomp recommends that you allow the electronics to operate for three minutes after first turning power on. This allows the electronics to become stable for maximum accuracy before you check the calibrations. Make sure no weight is on the hook. Press the ZERO switch.
CS200, Users August, 2009 How to calibrate the CS200 The following details the calibration procedure for the Intercomp CS200 crane scale. There are four parameters that can be set before entering the actual calibration. When changing a value, advance at least to “save save” save before turning off so that your changes are saved.
CS200, Users August, 2009 scale, but will also use the battery life more quickly. Press Zero until the desired read rate is displayed. (see cal menu table above) Enter the read rate (1 to 7). Press ZERO and BACKLIGHT together and release to enter the number 6. The scale shows “azt azt”. azt Press ZERO and BACKLIGHT together and release. Enter (0) to turn the auto-zero tracking off, enter (1) to turn it on. When on, small loads (+/- 3 divisions) will automatically be zeroed off after a few seconds.
CS200, Users August, 2009 Weight Calibration 10. The scale shows “CAL CAL”. CAL Press ZERO and backlight keys together and release. The recommended calibration type is 3 point linear. Enter “0101”. Otherwise enter “1” for a 1 point calibration. 11. The scale shows “LL00 LL00”. LL00 With no weight on the pad, press ZERO and BACKLIGHT together and release. This reads the pad zero. 12. The scale shows “LL01 LL01”. LL01 Apply the first weight/force. Press the ZERO and BACKLIGHT keys together and release.
CS200, Users August, 2009 Error Messages dISP EEPE OE OvEr BATT Display error, the scale is unable to display the number completely. If no weight on the scale, press zero to return the weight reading to zero. EEPROM error, the scale has had it's calibration corrupted or destroyed; the scale will require calibration. The scale is over capacity or outside the A/D converter range. Reduce the load to the scale.
CS200, Users August, 2009 How to reach Intercomp Things to know: The service is for a CS200. When did you purchase your CS200? What is your serial number? Whom did you purchase the CS200 through? For Intercomp Service call or fax: FAX # (763)-476-2613 (763)-476-2531 1-800-328-3336 or fill out the Service Support form at: www.intercompcompany.
