www.vip-vision.com MODEL: NVR4PROPACK Professional IP Surveillance Pack Network Video Recorder with 4 Security Cameras ‘QUICK INSTALLATION GUIDE’ N517 NVR 4 x IP Day/Night Cameras - Advanced H.264 Video Compression Technology - High Quality 1.
Package Contents (Before installation, please ensure you have all the parts listed below). 1 x Network Video Recorder with 1TB Hard Disk Drive ● Advanced H.264 Video Compression Technology for High Quality Images ● Easy to Operate ● Can be Connected to a PC Network for Remote Viewing & Backup (Software on Disc) 4 x Day/Night Weatherproof Colour Cameras with Infrared LEDs - 20m Range ● IR LEDs for Viewing in Total Darkness up to 20m (B&W Mode) ● 720p Resolution, 1.
Installation Before installing this unit, please read through the following points: • Do not place cords from the AC adapter where they can be pinched or stepped on. • Leave at least 50mm of space between the NVR and other objects to allow air circulation. • Do not expose the NVR or Cameras to excessive heat, cold, or moisture. • Never immerse any component in water, and do not spray cleaners of solvents on the unit. Unplug units before cleaning. When cleaning, use a damp, lint-free cloth only.
Connection Guide 1. 2. 3. 4. 5. 6. 7. Mount the 4 Cameras as required and connect them to the in-built POE Network Switch using the supplied Network Cables. Connect the 48V Power Supply to the in-built POE Network Switch portion. Connect the 12V Power Supply to the NVR portion. Plug both power adaptors into a Power-point. Switch NVR on from back of device. Hold Power button for 3 seconds.
Main Screen Once booted, you will be presented with the screen below. Each camera view will have one or more symbols from below: 1 2 Currently Recording Motion Detected 3 4 Video Loss Camera Lock NVR4PROPACK only supports four cameras. System Menu • • • • Right Clicking anywhere on the screen will bring up the System Login screen. Once Logged In, right clicking again will bring up a menu. Selecting “MAIN MENU” will show the system menu.
Set the Time and Date When using your NVR for the first time, you will have to set the SYSTEM TIME. • Right clicking anywhere on the screen will bring up the password menu. Use the mouse to enter the NVR admin password with the on-screen keypad. Default: The default username is admin, the password is also admin. (Users can alter the password later.
To Connect Cameras NOTE: The NVR will most likely automatically configure the IP address of a camera connected to the dedicated POE Ports on the back of the device. • • • Right click to open the menu and select “MAIN MENU”. Select “SETTING” Select “REMOTE DEVICE” Adding new Cameras 1. Click IP Search, this will list all cameras connected in the upper panel. 2. Click on the camera you wish to connect and click ‘Add’ Manual Adding 1. Click Manual Add 2.
To Set Up Recording Rates Record Times: The NVR4PROPACK system is capable of storing 2 weeks of recorded footage based on 1Tb of storage and the 4 included 1.3MP Cameras set to 720P @ 15fps and VBR @ Quality 5. • • • Right click to open the menu and select “MAIN MENU”. Select “SETTING” Select “ENCODE” We recommend: That each camera be set to H.264 with a maximum of 1280x720 resolution, 15fps, Bit Rate: VBR with Quality set to 5.
Motion Detection Motion detect recording is set per camera, per time period and can also be set to detect in certain portions of the screen. • • • Right click to open the menu and select “MAIN MENU”. Select “SETTING” Select “DETECT” • • • • • Select ‘Motion Detect’ from Event Type Select channel from Channel drop down Check the Enable box Ensure Record Channel is checked, and a Region has been selected. Click Save.
Playback • • Right click to open the menu and select “MAIN MENU”. Select “SEARCH” 1. Playback Controls • Click to begin playback, pressing it again will pause playback. • Click to stop playback. • Click to begin backwards playback • Click or to skip to the next session, or while paused to skip backward/forward a single frame. • Click during playback to play slower. • Click during playback to play faster. • Click to do a smart search. • Use • Click to control the volume.
2. Seek Control This shows the recorded data for the selected day. Normal recording in green, Alarm recording in red and Motion recording in yellow. Clicking on any part of the recorded data will jump to that time. This control is made up of 1-4 bars, which correspond to each camera channel currently viewed. 3. Playback Mode Display only recordings of the selected type(s). 4. Search Type Select whether to search from hard drive or external source. Select whether to search recordings or snapshots. 5.
Networking Important: Before setting up remote access for your NVR, you will need to have a good understanding of computer networking. Otherwise please seek the assistance of a qualified I.T. person. • • • Right click to open the menu and select “MAIN MENU”. Select “SETTING” Select “NETWORK” The device comes pre-configured to DHCP. If not, you need only to check the DHCP box and click save, settings will be allocated automatically. If this does not suit your needs, see the example below.
DMSS Mobile App App available for Android, iOS, Blackberry, Symbian, Windows Mobile and Windows 7 mobile From your compatible Smartphone, access the App Marketplace and download the free “DMSS Lite” App. This will be listed as: iDMSS for iOS gDMSS for Android DMSS for other Setting Up: • Enter “Device manager” and select “ADD”. • Enter in your devices details: Name may be anything, refer to your network settings for Address and TCP Port.
Troubleshooting Please refer to the FAQ table below for easy troubleshooting. The table below describes some typical problems and their solutions. Please consult these guides before contacting your NVR dealer. PROBLEM SOLUTION No power - Check power cord connection. - Confirm that there is power from the outlet. - Ensure that the 12V 5A is connected to the NVR Motion Detection not working - Ensure that motion detection is enabled for that channel in the “DETECT” menu.
Limited Warranty Cornick Pty Ltd (Seller) warrants its products to be in conformance with its own plans and specifications and to be free from defects in materials and workmanship under normal use and service for forty eight months from the date of original purchase.
PLEASE CUT OUT & RETURN THIS INFORMATION WITHIN 14 DAYS OF PURCHASE TO: RhinoCo Technology 9 Hannabus Place McGraths Hill NSW 2756 Australia M o d e l : N V R 4 P R O PA C K P r o f e s s i o n a l S u r v e i l l a n c e P a c k Wa r r a n t y C a r d Name Address Suburb State Postcode Email Date of Purchase Invoice Number Daytime Phone Where did you purchase your NVR4PROPACK? Store Location This information will only be used by the manufacturer and will not be sold to any third parties.
