VSP 1314 User’s Manual Manual #：RGB-RD-UM-V1314 E001 Revision:V1.
VSP 1314·User’s Manual Thank you for choosig our products! In order to allow you to learn how to use the video processor quickly, we bring you the detailed user’s guide. You can read the introduction and directions before using the video processor, please read all the information we provide carefully to use our products correctly. Copyright ©2012 All rights reserved by RGBLINK. This document is done by Xiamen RGBlink Science & Technolog Co.,Ltd independently.
be informed immediately in writing of any complains. The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of commissioning, at latest 30 days after the transfer of risks. In the event of justified notice of compliant, RGBlink can repair the fault or provide a replacement at its own discretion within an appropriate period.
Company address RGBlink Science & Technology Co., Ltd. Headquarter: S603~604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C Shenzhen office: Building 3, A Baiwang Plaza, Xili Nanshan District Shenzhen, Guangdong Province, P.R.C Beijing office：Room 410, Building 3, Dongyi International Business Park, No.8 Gaojing Culture Garden, Chaoyang District, Beijing, P.R.C Shanghai office:Building 3, 1358 Nong, Tongpu Road, Shanghai,P.R.
Operators Safety Summary The general safety information in this summary is for operating personnel. Do Not Remove Covers or Panels There are no user-serviceable parts within the unit. Removal of the top cover will expose dangerous voltages. To avoid personal injury, do not remove the top cover. Do not operate the unit without the cover installed.
Terms In This Manual and Equipment Marking WARNING Highlights an operating procedure, practice, condition, statement, etc, which, if not strictly observed, could result in injury or death of personnel. Note Highlights an essential operating procedure,condition or statement. CAUTION The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Change History The table below lists the changes to the Video Processor User’s Guide. Format Time ECO# Description Principal V1.
CONTENT CONTENT .........................................................................................8 1. Introduction ........................................................................... 12 Chapter Structure ........................................................................... 13 How to Use This Manual ................................................................. 14 Terms and Definitions ...................................................................... 15 System Overview .......
OUTPUT Interface .................................................................................... 25 12.13.22.23: Gigabit copper port............................................................ 25 14.24：Power supply port of Sending Card ......................................... 25 15.25：USB control port of sending card ............................................. 25 16.26：DVI Input ....................................................................................... 25 20：DVI Output .................
MENU---Output.......................................................................................... 39 MENU---Split .............................................................................................. 41 MENU---View ............................................................................................. 42 MENU---USB Setting ................................................................................ 42 MENU---Test Pattern ..............................................................
How to select switching effect ......................................................... 57 How to set input matrix .................................................................... 59 How to set DVI3 as background ..................................................... 60 How to splicing with DVI3 ................................................................ 62 How to use BLACK .......................................................................... 65 How to use Test Pattern ........................
1. Introduction This chapter is designed to introduce you to the VSP 1314 User’s Manual.
1.Introduction Chapter Structure Chapter Structure The following chapters provide instructions for all aspects of VSP1314 operations.
1.Introduction How to Use This Manual How to Use This Manual Following are important tips for streamlining your use of this User’s Manual in its electronic ―PDF form. Navigating Use Acrobat Reader’s ―bookmarks to navigate to the desired location. All chapter files have the same bookmark structure for instant navigation to any section. Please note: Extensive hyperlinks are provided within the chapters.
1.Introduction Terms and Definitions Terms and Definitions The following terms and definitions are used throughout this guide. “ASCII”: American Standard for Information Interchange. The standard code consisting of 7-bit coded characters (8 bits including parity check) used to exchange information between data processing systems, data communication systems, and associated equipment. The ASCII set contains control characters and graphic characters.
1.Introduction Terms and Definitions most commonly used color bars are eight full field bars. In the computer, the most commonly used color bars are two rows of reversed color bars. “Color burst”: In color TV systems, a burst of subcarrier frequency located on the back porch of the composite video signal. This serves as a color synchronizing signal to establish a frequency and phase reference for the chroma signal. Color burst is 3.58 MHz for NTSC and 4.43 MHz for PAL.
1.Introduction Terms and Definitions primarily in consumer electronics for the transmission of uncompressed high definition video, up to 8 channels of audio, and control signals, over a single cable. HDMI is the de facto standard for HDTV displays, Blu-ray Disc players, and other HDTV electronics. Introduced in 2003, the HDMI specification has gone through several revisions. “HDSDI”: The high-definition version of SDI specified in SMPTE-292M.
1.Introduction Terms and Definitions “Polarity”: The positive and negative orientation of a signal. Polarity usually refers to the direction or a level with respect to a reference (e.g. positive sync polarity means that sync occurs when the signal is going in the positive direction). “RJ-45”: Registered Jack-45. A connector similar to a telephone connector that holds up to eight wires, used for connecting Ethernet devices.
1.Introduction Terms and Definitions correct time. For example, horizontal sync determines exactly when to begin each horizontal scan line. Vertical sync determines when the image is to be refreshed to start a new field or frame. There are many other types of sync in video system.(Also known as ―sync signal‖ or ―sync pulse.‖) “TCP/IP”: Transmission Control Protocol/Internet Protocol. The communication protocol of the Internet.
1.Introduction System Overview System Overview The VSP 1314 is a 3 layers seamless switcher and scale that accepts a wide variety of video signals,including RGB computer-video, HDTV, which support 4 composite (CVBS),2 VGA, 2 DVI (compatible with HDMI1.3),2 USB inputs and 2 DVI3(background window). It combines truly seamless, glitch-free switching with advanced scaling technology to meet the requirement of high quality,high resolution video presentation.
1.Introduction Application Questions Application Questions RGBlink offers solutions to demanding technical problems. Any application questions, or required further information, please contact with our Customer Support Engineers. Refer to Appendix B for contact details.
2. Hardware Orientation In This Chapter This chapter provides detailed information about the VSP 1314 hardware.
2.Hardware Orientation VSP 1314 Rear Panel VSP 1314 Rear Panel This chapter provides detailed information about the VSP 1314 hardware. The following topics are discussed: NO. INTERFACE NO. INTERFACE 1 USB Input 12.13.21.23 Gigabit copper port 2~5 CVBS Input 14.24 Power supply port of Sending card 6. 7 VGA Input 15.25 USB control port of sending card 8 Dial Switch 16~19.26 DVI Input 9 10/100M Interface 20.
2.Hardware Orientation VSP 1314 Rear Panel 2~5：CVBS Input CVBS 1/2/3/4 input. Can receive standard video signal from players, cameras etc. Input supported resolution 480i and 576i via BNC. Supported standards include: PAL, NTSC and SECAM. 6.7: VGA Input VGA 6/7 Input Interface, input the video signal from HD player and Computer, etc. Compatible with YPbPr signal, input signal via the DB9 interface. 17.18.19：DVI Input DVI 17/18 input.
2.Hardware Orientation VSP 1314 Rear Panel 11.RS232 Interface Used to connect the computer. OUTPUT Interface 12.13.22.23: Gigabit copper port Gigabit copper port, connect to LED screen. 14.24：Power supply port of Sending Card Power has been already supplied by video processor itself, don’t need external power supply. 15.25：USB control port of sending card 16.26：DVI Input Input the DVI out originating from other video processors.
2.Hardware Orientation VSP 1314 Rear Panel Switch and Power 27.28：Power Interface and Switch AC 90-264V 3.
2.Hardware Orientation VSP 1314 Front Panel VSP 1314 Front Panel Insert power cord and push power to ON position. LCD module on the front panel will show RGBLINK and go into self verification before it load last setting config and send processed image to the target monitor. For the first setup, DVI input is default source. With front panel keyboard, user can operate VSP 1314 through the menus on LCD panel.
2.Hardware Orientation VSP 1314 Front Panel VSP 1314 front panel as following: LCD panel Used to show the key and communication interactive menu. Menu Buttons Color operation panel: Green light means on work； Red light means optional choice for work; MENU/EFFECT：Menu and Effect function multiplexing button; Press it and light up green to enter to Menu function,the LCD panel shows content of MENU,rotate and press the adjust knob select MENU.Press again to reback the last Menu.
2.Hardware Orientation VSP 1314 Front Panel Detail please refer to How to select switching effect. PIP1/PIP2：PIP mode multiplexing button； Press button and light up green,that means is1/2 mode;layer 1 above layer2； Press button and light up red,that means is 2/1 mode;layer 2 above layer1 LCD showss as following: PIP A/B Detail please refer to How to set picture in picture.
2.Hardware Orientation VSP 1314 Front Panel save.LCD will show Load From,after finish loading, the button which selected will light out,and other 9 lights light up still.It means can load other infomation .Press button again the red light light out it means have exit Load mode.
2.
2.
2.
3. Hardware Installation In This Chapter This chapter provides comprehensive installation instruction for VSP 1314 hardware： Following is the size of VSP 1314 for your reference.
Safety Precautions For all VSP 1314 processor installation procedures, please observe the following important safety and handling rules to avoid damage to yourself and the equipment. To protect users from electric shock, ensure that the chassis connects to earth via the ground wire provided in the AC power Cord. The AC Socket-outlet should be installed near the equipment and be easily accessible. Unpacking and Inspection Before opening VSP 1314 process shipping box, inspect it for damage.
4. Menu Orientation In This Chapter This chapter describes all VSP 1314 processor menus, including how they are accessed, the functions that are available, and descriptions of each menu tree (in block diagram format).
4.Menu Orientation MENU MENU Press MENU/EFFECT, button light up green light,that is you can enter the main menu,as following: rotate the adjust knob can select the up and down menuitem;When the munuitem added to a blue bar ,it means is in a selecred state,press knob to make sure and enter to the corresponding menu to set or view.
4.
4.Menu Orientation MENU MENU---Input Press MENU/EFFECT ,it light up green to enter to MENU and rotate the adjust knob to select Input and press to make sure.LCD panel show the information of input resolution and input matrix ;As picture above,If user need to change input signal source ,rotate the adjust knob to select the matrix,press knob can enter the corresponding channel setting;Channel 1 and Channel 2 can input 1 or input 2,Channel 3 can select test picture or input DVI3.
4.Menu Orientation MENU When input signal to the large screen,boundary appear black side,can use this function to adjust to make full screen display. Select DVI1,rotate the adjust knob can choice the HDMI/DVI interface,Default interface is DVI output.If you need HDMI output,please select HDMI. Select DVI1 also can choice color format,Color range of video format is 16-235,Color range of image format is 0-255. The same method can be applied to set the DVI2 output.
4.Menu Orientation MENU In addition need to adjust the numerical range at 0~174，other at 0~255. Background： rotate the adjust knob can choice the background,TP is Test Picture,DVI3 is Background input . Note Background resolution of image is the same with output resolution； Detail please refer to How to set DVI3 as background.
4.Menu Orientation MENU MENU---View Delay Call Save: Set delay the output time,When more than one equiment power on,and the processor is the end equipment in order to improve question that can’t identify the input signal and phenomenon that LED screen appear messy code and flash screen,now need to delay the input time. MENU---USB Setting USB Photo Play Time;Use this when you need play photo for o long time.
4.Menu Orientation MENU Authorized setting：This product have been useing time limited by our company,if it is service life and need to continue to use,you must to contact with our sales or service to get the password. State：Authorized and unauthorized； MENU--- OLED Luminance Enter can set the luminance of font； MENU--- Video Firmware Update User can update video firmware via USB1~USB4.
4.
5. System Setup and Operation In This Chapter This chapter provides detailed information about the control communication software.
5.System Setup and Operation How to connect equipment How to connect equipment NO INTERFACE NO INTERFACE 1 USB Input Interface 12.13.21.23 Gigabit nets connector 2~5 CVBS Input Interface 14.24 Send card power source 6. 7 VGA Input Interface 15.25 Send card USB control connector 8 Dial Switch 16~19.26 DVI Input Interface 9 10/100M Interface 20.21 DVI Input Interface 10 USB Interface 27 Power 11 RS232 Control Interface 28 Switch 20.
5.System Setup and Operation How to connect equipment preview signal.Output signal via DVI-I interface（Preview adopt standard DVI-I interface,compatible with VGA output,switch VGA output via terminil.
5.System Setup and Operation How to make equipment normal operation How to make equipment normal operation 1. Make sure equipment normal operation; 2. After power on equipment starts self state,fan starts,scan button; 3. After scanning,LCD will show as following: AVDSP Series VSP 1314 Seamless Switcher & Scaler System Initializing 100% CH1:DVI1 NO INPUT CH2:DVI2 NO INPUT 3 Output: 1 A F V1 V2 1024X768 60Hz 4.
5.System Setup and Operation How to preview input signal source How to preview input signal source Make sure equipment normal operation.Detail please refer to :How to make equipment normal operation Operation as following： 1. The signal of green light output from Program,can check output if connect monitor or LED screen send card; 2. The signal of yellow light output from Preview,can check output if connect monitor; 3. The signal of red light can preview switching,can check image at preview output; 4.
5.System Setup and Operation How to adjust output resolution How to adjust output resolution Make sure equipment normal operation.Detail please refer to :How to make equipment normal operation Operation as following: 1. Press light up green light to enter to MENU; 2. LCD shows the menu mode,rotate the adjust knob to select OUTPUT; Input Output Split View 3. Press knob to make sure,Enter to OUTPUT to select Output Format; Output Format Output Adjust Screen Aspect Ratio 4.
5.System Setup and Operation How to adjust size and position of image How to adjust size and position of image Make sure equipment normal operation.Detail please refer to : How to make equipment normal operation Operation as following: Three button combination operation as following: SCALE： 1. Press SCALE/CROP，light up green light-SCALE setting; 2.
5.System Setup and Operation How to adjust size and position of image DVI2 Scale HSize Scale HPos Scale VSize Scale VPos <1024> < 0> < 768> < 0> 4. Press V SIZE/V POS ,light up green light-Width setting,rotate the adjust knob can adjust the weith of image; DVI2 Scale HSize Scale HPos Scale VSize Scale VPos <1024> < 0> < 768> < 0> 5.
5.System Setup and Operation How to scale image How to scale image Make sure equipment normal operation.Detail please refer to : How to make equipment normal operation Operation as following: Three button combination operation as following: CROP: 1. Press SCALE/CROP，light up red light-scale setting; 2. Press H SIZE\H POS,light up green light-Height setting,rotate the adjust knob can adjust height of image; DVI2 Crop HSize Crop HPos Crop VSize Crop VPos < 100> < 50> < 100> < 50> 3.
5.System Setup and Operation How to scale image 4. Press V SIZE/V POS,light up green light-width setting,rotate the adjust knob can just width of image; DVI2 Crop HSize Crop HPos Crop VSize Crop VPos < 100> < 50> < 100> < 50> 5.
5.System Setup and Operation How to switch signal of single image How to switch signal of single image Make sure equipment normal operation.
5.System Setup and Operation How to set picture in picture How to set picture in picture Make sure equipment normal operation.Detail please refer to :How to make equipment normal operation PIP Functional description: Before press, make sure signal firstly; Such as want set VGA1 as big picture,size is::960x672，and set DVI2 as small picture,size is:384x384,position is:X-288,Y-144 Operation as following: 1. Set VGA1 as Preview output,scale to:960x672； 2. Press TAKE to switch VGA1 as Program output; 3.
5.System Setup and Operation How to select switching effect How to select switching effect Make sure equipment normal operation.Detail please refer to :How to make equipment normal operation Operation description: TAKE is the effect switch button. The switching effect must be setted in menu.After setting,press TAKE to switch. Operation as following: 1.Press and button light up red;Rotate the 2.adjust knob to select switch effect.
5.System Setup and Operation How to select switching effect 3.
5.System Setup and Operation How to set input matrix How to set input matrix Make sure equipment normal operation.Detail please refer to :How to make equipment normal operation Operation description: This function can support 2 or 3 layers to play the same videos,to meet various requirements. Operation as following: 1.Press and light up green; 2.LCD shows the MENU,rotate the adjust knob to select Input; Input Output Split View 3.Press the adjust knob to ensure,and rotate the adjust knob to select 3.
5.System Setup and Operation How to set DVI3 as background How to set DVI3 as background Make sure equipment normal operation.Detail please refer to :How to make equipment normal operation Operation description: The system default background for test pattern,There are two ways to use background:One is to use own test pattern,anther one is to use DVI3 inout signal;It must make sure the input resolution of DVI3 is the same with equipment before set DVI3 as background; Operation step as following: 1.
5.System Setup and Operation How to set DVI3 as background 5.
5.System Setup and Operation How to splicing with DVI3 How to splicing with DVI3 Make sure equipment normal operation.
5.System Setup and Operation How to splicing with DVI3 Split Switch： Split Mode： Split Output Channel: Display Width： ON H 1/2 DVI1 1024 6. Press the adjust knob and rotate it to select Split Output Channel,press to enter it.There are DVI1 and DVI2.
5.System Setup and Operation How to splicing with DVI3 8.Repeat above operation step to adjust the output image,That is adjust the size and position of output image; Screen Height： Screen Local X： Screen Local Y： Config Update (Push OK) 768 0 0 9.Parameter correction,If splicing is stagger or there is a flower on screen,because of DVI3 input interrupt or unstable,can correct the parameter.
5.System Setup and Operation How to use BLACK How to use BLACK Make sure equipment normal operation.Detail please refer to :How to make equipment normal operation BLACK： Black signal is a special effect which in order to set background directlly in the special scene. VSP1314 default layer 3 as background,That is button 0 is the background; Operation step as following: 1.Press and light up yellow ,at preview can 2.check the image; 3.If is not background,please press and light up green.LCD shows the 4.
5.System Setup and Operation How to use Test Pattern How to use Test Pattern Make sure equipment normal operation.Detail please refer to :How to make equipment normal operation Test Pattern: If there is no signal source from outside,the equipment have own test pattern,like as a video generator, can meet different scene; Operation step as following: 1.If is not background please press and light up green,rotate the adjust knob to select Test Pattern; USB Setting Test Pattern Language System 2.
5.System Setup and Operation How to save parameter How to save parameter Make sure equipment normal operation.Detail please refer to :How to make equipment normal operation User save user can load diferent scene directly There are 10 group of save; Operation step as following: 1.Press and light up green; 2.Button1，2，3，4，5，6，7，8，9，10 light up green at the same time; 3.
5.System Setup and Operation How to load parameter How to load parameter Make sure equipment normal operation.Detail please refer to :How to make equipment normal operation User can load saving directly.There are 10 groups of load; Operation step as following: 1.Press and light up red; 2.Button1，2，3，4，5，6，7，8，9，10 light up red at the same time; 3.Select the position of load,press that button and button light off; 4.
A.Specification CVBS Input Number of inputs 4 Connector Standard BNC Socket Supported PAL/NTSC Standard Signal 1Vpp±3db Supported 480i,576i (0.7V Video+0.3v Sync ) 75 ohm Resolution VGA Input Number of inputs 2 Connector Standard DB9 Socket Supported VGA-UXGA Standard Signal Level R、G、B、Hsync、Vsync:0 to1Vpp±3dB (0.7V Video+0.
Connector Standard DVI-I Socket Supported VESA：800×600×60Hz，1024×768×60Hz，1280×768×60Hz， Resolution 1280×1024×60Hz，1600×1200×60Hz，1920×1080×60Hz Signal Level TMDS pwl，single pixel input，165MHz bandwidth Standard DVI 1.
B.Contact Information Warranty： RGBlink Science & Technology Co., Ltd policy is 1 year warranty and 3-year labor warranty since delivery day for the main components (basic motherboard, internal power supply, keyboard, LCD module, VGA input module, CVBS input module, DVI input module, sending card, etc.). Within the guaranteed maintenance period, customers can send back the products if malfunction, and freight users from themselves.
C.Firmware Upgrade Function Firmware Upgrade 1. Firstly, connect device and computer with reticle; input network address of VSP 1314 firmware upgrade in the address bar: 192.168.0.100; 2. Input your user name admin in the popup dialog box, rgblink: 123 password. 3.
4.press【browse„】choose upgrade document, the name of document must be:xxx.bin or xxx.fon； 5.
6. It will show :Upgrade Font Success after finish.And restart the equipment to check whether operation is normal. Image Firmware Upgrade All the two USB interface must be upgraded.Because it can improve the image quality,the upgrade etepsare as following: 1、Input USB enter to USB interface. 2、After start equipment enter to the menu,and find the menu of（Video fireware Updata），can select USB1 and USB2.
Communication Firemware Upgrade Shut the power device, switch the direction of arrow of the two dial switch which download IP board to ON state. As shown in figure: Connect one end of RJ11 download line to RS232 .control Connector of video processor end access and the other end access PC serial port.
When download is finish, quit, shut the power equipment, reset two dial code reset (as shown in figure), restart the power equipment, check whether the equipment operate or not. Note Flash Magic software download website: http://www.flashmagictool.com/download.html&d =FlashMagic.
