User Manual

ManualsBrandsRGBlink ManualsCamcordersRGB3X-EPTZ-BK Educational Tracking Camera - EDUCATIONAL CAMERA WITH TRACKING AND 3X DIGITAL ZOOM

Table Of Contents

EPTZ Educational Tracking Camera

RGB3X-EPTZ-BK

User Manual

Summary of content (40 pages)

PAGE 1
EPTZ Educational Tracking Camera RGB3X-EPTZ-BK User Manual
PAGE 2
Content Declarations................................................................................................................................................................ 3 FCC/Warranty........................................................................................................................................................... 3 Operators Safety Summary....................................................................................................................................
PAGE 3
6.4 Pelco-P Protocol Command List...................................................................................................................33 6.5 Terms & Definitions......................................................................................................................................... 34 6.6 Revision History...............................................................................................................................................
PAGE 4
Thank you for choosing our product! This User Manual is designed to show you how to use this camera quickly and make use of all the features. Please read all directions and instructions carefully before using this product. Declarations FCC/Warranty Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC rules.
PAGE 5
To avoid personal injury, do not remove the top cover. Do not operate the unit without the cover installed. Power Source This product is intended to operate from a power source that will not apply more than 230 volts rms between the supply conductors or between both supply conductor and ground. A protective ground connection by way of grounding conductor in the power cord is essential for safe operation. Grounding the Product This product is grounded through the grounding conductor of the power cord.
PAGE 6
adequate power, ventilation, and space for all components. Electric Safety Installation and operation must accord with electric safety standard Polarity of power supply The power supply of the product is DC12V, the max electrical current is 2A .Polarity of the power supply as the following drawing. Careful of installation Never move the camera by seizing the camera head. Don’t rotate camera head by hand; otherwise, mechanical trouble will occur.
PAGE 7
Chapter 1 Your Product 1.1 Product Overview Educational tracking camera integrates with industry leading 4K ultra-definition imaging technology, image encoding and decoding technology, video analysis technology and electronic PTZ control technology, and realizes a single camera to output close-ups main stream, close-up sub-stream, panoramic main stream, panoramic sub-stream and blackboard stream at the same time.
PAGE 8
1.3 Interface 1. Camera Lens 2. Tripod Screw Hole 3. Tripod Screw Hole 4. USB3.0 Interface 厦门视诚科技有限公司 5.SDI Interface 6. LAN Interface 7. Reset button 8. A-IN 9. RS232/ RS485 10. Power Interface 11. Power Indicator 地址：厦门市火炬高新区创业园伟业楼 S601 网址：www.rgblink.
PAGE 9
1.4 Dimension 厦门视诚科技有限公司地址：厦门市火炬高新区创业园伟业楼 S601 网址：www.rgblink.
PAGE 10
Chapter 2 Install Your Product 2.1 System Connection Installation Layout Teacher tracking camera is installed at place 1.6-2.1m from ground (distance from panoramic lens to ground), and the distance from the blackboard is 5-9m. Teacher tracking camera should be installed near central axis of the classroom as much as possible to get the best result of tracking camera shooting.
PAGE 11
厦门视诚科技有限公司地址：厦门市火炬高新区创业园伟业楼 S601 网址：www.rgblink.
PAGE 12
Chapter 3 Use Your Product 3.1 Browser Login and Track Setup Process 3.1.1 Connecting Mode Direct connection: Connect the camera via network cable to external Internet access of the PC Internet connection mode: Connect the camera to Internet by Router or Switch and user can log in the device by browser. Note: Please do not put the power and network cable in places where can be easily touched to prevent video quality lowered by unstable signal transmission due to poor contact of cables.
PAGE 13
3.2 Browser Login 1) Web Client Login Input the IP address 192.168.5.163 of the device in the address filed of browser and click Enter button to enter into Web Client login page as below picture. User can login as administrator and normal user.
PAGE 14
3.4 Browser Configuration Click Configuration to enter into the device parameters setting page There are the following options: audio configuration, video configuration, network configuration and system configuration, detailed description see the following table. Menu Audio configure Video configure Network configure System configure Explanation Including audio compressing format, sampling frequency, sampling precision, compressing code rate settings etc.
PAGE 15
optional; panoramic sub-stream default 512Kb/s, 64-40960Kb/s optional; and broadcast code stream default 4096Kb/s, 64-40960Kb/s optional). Frame rate (F/S): Set the video frame rate (close-up main stream, close-up sub-stream, panoramic main stream, panoramic sub-stream, and broadcast code stream default 25F/S, main stream 5-30F/S optional).
PAGE 16
White balance modes: Set the white balance mode (the default automatic, 2400K-7100K, manual, One-push optional). Note: Click the “Correction” button when selected the One-push white balance mode. Red fine-tuning: default 0, -10~10 (only available in automatic mode) Blue fine-tunable: default 0, -10~10 (only available in automatic mode) Saturation: Set the saturation (default 60%, 70%, 80%, 90%, 100%, 110%, 120%, 130%, 140%, 150%, 160%, 170%, 180%, 190%, 200% optional).
PAGE 17
3.4.
PAGE 18
3.4.4 System Configuration 1) Device Properties Device Name: Set the device name (the default Camera1, user can add their own). Device ID: Set the device ID (default 1, Read-Only). System Language: Set the system language (default Simplified Chinese, English optional).Need to re-login after modify and save the setting. Click on the "Save" button, it will be valid when display "Save successful".
PAGE 19
automatically and restore factory setting. 6) Reboot Click on the pop-up "Reboot" button and choose “yes” or “no”, then the device will restart automatically. 3.5 Logout Point "Logout" pop-up "Confirmation" dialog; select "Yes" or "No", choose “Yes” to exit the current page and return to the user login interface again. 3.
PAGE 20
1. Click stop tracking 2. Preset setting of the platform The operation interface for setting the preset position is shown in Figure below. By controlling the position and ZOOM value of the PTZ, the camera Angle and position are adjusted to the preset position and saved. The description of the preset position of the podium is as follows. 厦门视诚科技有限公司地址：厦门市火炬高新区创业园伟业楼 S601 网址：www.rgblink.
PAGE 21
Platform preset: Control teacher tracking camera to make platform (we suggest that teachers stand in the middle of platform, if any) get desired visual result in camera image, then click and save platform preset. During normal tracking, size of teacher’s image in the picture uses Platform preset as a reference. When tracking target disappears, it can select close-up lens to go back to platform preset. 3.
PAGE 22
4. Area settings (ON: show the mask area; OFF: hide the mask area) 5. Platform area: It is the area tracked once close-up lens start up tracking. It is blackboard area on platform generally so as to ensure that when teacher is on platform, his upper body is displayed within setting area, and it will not exceed lower margin of platform area when students in the first row sit down. See Figure below. 6.
PAGE 23
Track mode (Three for option): Real-time Tracking Mode Movie Mode Area Tracking Mode Tracking sensitivity: It means in teacher tracking mode, how much the action range is required to trigger tracking camera when the tracking target changes from stationary state to motion state. The higher the action sensitivity, the smaller movement of tracking target that will trigger camera’s tracking motion. Tracking speed: It means speed of tracking camera for horizontal tracking.
PAGE 24
Target lost time(s): It means how much time is required (0s by default) for tracking camera to perform “target lost action” when target is lost (default: return to panoramic preset). Inter PGM: It is chosen default. Student IP address: Fill in the IP of the student tracking camera here. When the director stream is obtained, the close-up of the teacher tracking camera and the panoramic switch of the student tracking camera can be realized. 3.7 Description of Recording and Broadcasting Host 3.7.
PAGE 25
2. Configuration of action code Modify action code as needed via web browser. Click Advanced settings -> action code; After modification, click save, as shown below: 厦门视诚科技有限公司地址：厦门市火炬高新区创业园伟业楼 S601 网址：www.rgblink.
PAGE 26
Chapter 4 Ordering Code 4.1 Product 981-0011-18-0 厦门视诚科技有限公司 RGB3X-EPTZ-BK Educational Tracking Camera 地址：厦门市火炬高新区创业园伟业楼 S601 网址：www.rgblink.
PAGE 27
Chapter 5 Support 5.1 Contact us 厦门视诚科技有限公司地址：厦门市火炬高新区创业园伟业楼 S601 网址：www.rgblink.
PAGE 28
Chapter 5 Appendix 6.1 Specification Model Number Teacher Tracking Camera Camera/ Lens Parameters Image Sensor 1/2.8 inch High Quality 4K CMOS Sensor Effective pixels 8.28 megapixel, 16: 9 SDI output: 1080P@30fps/25fps;720P@60fps/50fps/30fps/25fps; U3 output:1920X1080P30 fps /25 fps;1280X720P60 fps /50 fps /30 fps /25 Video Format fps ;960X540P30 fps;800X600P30 fps;640X360P30 fps;640X480P30 fps;352X288P30 fps; USB3.0 can be compatible with USB2.0 output View Angle 57.2°（D）/47°（H）/36°（V） Focus f=7.
PAGE 29
6.2 VISCA Protocol List 6.2.1 Camera Return Command Ack/Completion Message ACK Completion z = camera address + 8 Error Messages Command packet z0 41 FF z0 51 FF Command packet Syntax Error z0 60 02 FF Command Not Executable z0 61 41 FF Note Returned when the command is accepted. Returned when the command has been executed.
PAGE 30
Command Function Reset Up Down Direct Reset Up Down Direct Full Auto Manual Command packet 8x 01 04 03 00 FF 8x 01 04 03 02 FF 8x 01 04 03 03 FF 8x 01 04 43 00 00 0p 0q FF 8x 01 04 04 00 FF 8x 01 04 04 02 FF 8x 01 04 04 03 FF 8x 01 04 44 00 00 0p 0q FF 8x 01 04 39 00 FF 8x 01 04 39 03 FF Shutter priority 8x 01 04 39 0A FF Iris priority 8x 01 04 39 0B FF Bright Reset Up Down Direct Reset Up Down Direct Gain Limit Reset Up Down Direct On Off Reset Up Down Direct On Off Reset Up Down Direct CAM_NR（2D）
PAGE 31
Command CAM_Memory CAM_LR_Reverse CAM_PictureFlip CAM_ColorSaturatio n Function Up Down Direct Reset Set Recall On Off On Off Direct 8x 01 04 49 00 00 00 0p FF ON OFF ON OFF On 8x 01 04 22 0p 0q 0r 0s FF 8x 01 04 06 06 02 FF 8x 01 04 06 06 03 FF 8x 01 06 08 02 FF 8x 01 06 08 03 FF 8x 01 7D 01 03 00 00 FF Off 8x 01 7D 01 13 00 00 FF Reset Direct Direct OFF Flip-H Flip-V Flip-HV 8x 01 04 A0 10 FF 8x 01 04 A1 00 00 0p 0q FF 8x 01 04 A2 00 00 0p 0q FF 8x 01 04 A4 00 FF 8x 01 04 A4 01 FF 8x 01 04 A4 0
PAGE 32
Command Function Right Upleft Upright DownLeft DownRight Stop AbsolutePositio n RelativePosition Home Reset Set Pan-tiltLimitSet Clear Command packet 8x 01 06 01 VV WW 02 03 FF 8x 01 06 01 VV WW 01 01 FF 8x 01 06 01 VV WW 02 01 FF 8x 01 06 01 VV WW 01 02 FF 8x 01 06 01 VV WW 02 02 FF 8x 01 06 01 VV WW 03 03 FF 8x 01 06 02 VV WW 0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF 8x 01 06 03 VV WW 0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF 8x 01 06 04 FF 8x 01 06 05 FF 8x 01 06 07 00 0W 0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF 8x 01 06 07 01 0W 07 0F 0F 0F 0
PAGE 33
CAM_FlickerModeInq 8x 09 04 55 FF y0 50 0p FF CAM_ApertureInq 8x 09 04 42 FF CAM_PictureEffectModeInq 8x 09 04 63 FF y0 50 00 00 0p 0q FF y0 50 00 FF y0 50 04 FF CAM_MemoryInq 8x 09 04 3F FF SYS_MenuModeInq 8x 09 06 06 FF CAM_LR_ReverseInq 8x 09 04 61 FF CAM_PictureFlipInq 8x 09 04 66 FF CAM_ColorSaturationInq 8x 09 04 49 FF y0 50 00 00 00 0p FF CAM_IDInq 8x 09 04 22 FF IR_ReceiveInq 8x 09 06 08 FF y0 50 0p FF y0 50 02 FF y0 50 03 FF y0 07 7D 01 04 00 FF y0 07 7D 01 04 07 FF y0 07 7D
PAGE 34
7:1080P25 ww: Pan Max Speed Pan-tiltMaxSpeedInq 8x 09 06 11 FF y0 50 ww zz FF Tilt Max Speed y0 50 0w 0w 0w 0w wwww: Pan Position Pan-tiltPosInq 8x 09 06 12 FF 0z 0z 0z 0z FF Tilt Position Note:[X] in the above table indicates the camera address to be operated,【y】=【x + 8】. zz: zzzz: 6.
PAGE 35
Zoom In 0xA0 Address 0x00 0x20 0x00 0x00 0xAF XOR Zoom Out 0xA0 Address 0x00 0x40 0x00 0x00 0xAF XOR Stop 0xA0 Address 0x00 0x00 0x00 0x00 0xAF XOR Focus Far 0xA0 Address 0x01 0x00 0x00 0x00 0xAF XOR Focus Near 0xA0 Address 0x02 0x00 0x00 0x00 0xAF XOR Set Preset 0xA0 Address 0x00 0x03 0x00 Preset ID 0xAF XOR Clear Preset 0xA0 Address 0x00 0x05 0x00 Preset ID 0xAF XOR Call Preset 0xA0 Address 0x00 0x07 0x00 Preset ID 0xAF XOR Query Pan
PAGE 36
definition signal/data interface (U-SDI) for transmitting 4K and 8K signals using a single optical cable. The interface was standardized as the SMPTE ST 2036-4. ●HDMI ： High Definition Multimedia Interface: An interface used for the transmission of uncompressed high definition video, up to 8 channels of audio, and control signals, over a single cable. ●HDMI 1.3: released on June 22 2006, and increased the maximum TMDS clock to 340 MHz (10.2 Gbit/s).
PAGE 37
simplicity in design comes along with great durability and affordable prices. ● LC：(Lucent Connector) is a small factor connector (uses only a 1.25mm ferrule diameter) that has a snap coupling mechanism. Because of its small dimensions, it is the perfect fit for high-density connections, XFP, SFP, and SFP+ transceivers. ● FC :(Ferrule Connector) is a screw type connector with a 2.5mm ferrule.
PAGE 38
protection of video during transmission between devices. ●HDBaseT: A video standard for the transmission of uncompressed video (HDMI signals) and related features using Cat 5e/Cat6 cabling infrastructure. ●ST2110: A SMPTE developed standard, ST2110 describes how to send digital video over and IP networks. Video is transmitted uncompressed with audio and other data in a separate streams.
PAGE 39
data. OSC is transported via UDP packets between devices connected on an Ethernet. ●Brightness：Usually refers to the amount or intensity of video light produced on a screen without regard to colour. Sometimes called black level. ●Contrast Ratio ： The ratio of the high light output level divided by the low light output level. In theory, the contrast ratio of the television system should be at least 100:1, if not 300:1. In reality, there are several limitations.
PAGE 40
●EDID: Extended Display Identification Data. EDID is a data structure used to communicate video display information, including native resolution and vertical interval refresh rate requirements, to a source device. The source device will then output the provided EDID data, ensuring proper video image quality. 6.6 Revision History The table below lists the changes to the camera User Manual. Format Time V1.