as82 of CD Control Module E 2.
Contents CD Control Module Installation Connection panel 2 3 4 Cabling & Setup Blu-ray Player Cabling Volume control Setup 5 5 5 6 7-9 Analogue inputs IN1 – IN3 Cabling Setup: Edit Name 10 10 11 General operation 12-13 Multiroom operation 14 Technical data Warranty 15 15 1
CD Control Re:source CD Control Module The CD Control module is a universal audio interface with a serial communication port. Blu-ray player specifications Company: Oppo / USA Model: BDP-93xx xx = Country code; e.g. EU, CH ... http://www.oppodigital.com/ Unlike the Re:system M51 and M100, the Re:system M10 device does not have an internal CD player.
CD Control Re:source INSTALLATION The CD-Control Module is equipped with the latest electronics and should be handled with care. Loosen the two screws with the TORX screwdriver supplied and remove the blanking plate. Before you install the card, the M51/M10 must be switched off and separated from the power supply, by plugging the unit out. Before removing the module from its packaging, you should make sure that you do not have any static electricity.
CD Control Re:source Connection panel 9-Pin Pin 2 Pin 3 Pin 5 ⇒ ⇒ ⇒ ⇒ 9-Pin Pin 3 Pin 2 Pin 5 Max. RS232 cable length: 10 m Audio connections The CD Control module independent audio inputs: IN 1 IN 2 IN 3 IN 4 for for for for has 4 Aux-1 Aux-2 Aux-3 BDP-93 Blu-ray player Devices such as external tuners, CD players, MiniDisc players or SAT receivers can be connected to the analogue line inputs IN1 to IN3.
CD Control Re:source Cabling & Setup Blu-ray Player: Input IN 4 + RS232 Two connections have to be made between the BDP-93 Blu-ray player and the CD Control module. 1.) Audio connection input IN 4 (CD Control module) with the audio output FLFR (BDP-93) using a stereo cinch cable. If a 5.1 Decoder module is available in the Re:system M51/M10, a digital audio connection can be established in addition - see "Configuring the digital input". 2.) RS232 control connection with a serial null modem cable.
CD Control Re:source Volume control Compared with the internal Multiroom sources from the M series, the signal level on the audio output (cinch socket FL/FR) on the BDP-93 Blu-ray player, is too high. The output level of the Blu-ray player has to be reduced, in order to achieve a uniform volume for all sources. The level adjustment is done through the Vol +/- buttons on the remote control and the correct output level setting is 85 (from 100).
CD Control Re:source Setup CD Control Configuring the digital input The basic settings for the CD Control module are made in Setup. When installing the CD Control module in a Re:system M51 or M10 with an installed 5.1 Decoder module, you have the option to use the digital audio signal from the Blu-ray player in the main room. In this case, the digital output (Coaxial/Optical) is connected to the digital input on the 5.1 decoder module at the M51.
CD Control Re:source Configuring the digital input Hiding analogue inputs You can now select whether and which of the 5.1 decoder digital inputs should receive the digital signal, using the Dig. Input function. On the second page of the Setup (Menu softkey), the CD Control module offers the option of hiding the Aux-1, Aux-2 and Aux-3 analogue sources, if required. This option is only available in the CD source Setup menu - [Source CD > Setup > Source].
CD Control Defining the behaviour Re:source CD switch-off Power Off: System Off After the CD has been paused or stopped, the Blu-ray player stays in this state. Only when all rooms including the main room are switched off, does the Blu-ray player switch to standby mode. In standby mode, the Blu-ray player needs 0.5 watts. If required, the Blu-ray player can be turned off completely through the serial interface. You have 3 different switch off [Power Off] options to choose from.
CD Control Re:source Analogue input IN1 IN2 IN3 Connect the three analogue inputs IN1 – IN3 using a cinch stereo cable with your external device. The inputs are shown in the source menu as Aux-1 – Aux-3. The analogue inputs IN1 – IN3 are not suitable for connecting a record deck. In this case, you should use the I/O module, which supports both MM and MC sound systems. Both modules, the CD Control module and the I/O module, can be used together in the M51/ M10.
CD Control Re:source Setup Aux-1 / 2 / 3 Edit source name The display names of the three inputs and the CD source can be freely defined. Simply give a name that you can assign clearly. The Cursor softkeys move the [ ] cursor left and right respectively. The Delete softkey deletes a character where the [ ] cursor is positioned. Select the input from the SOURCE menu whose name you want to edit. CD, Aux-1, Aux-2, Aux-3 The Insert softkey inserts a character to the left of the [ ] cursor.
CD Control Re:source General operation CD Menu If a CD Control module is installed, the sources Aux-1, Aux-2, Aux-3 and CD appear in the Source menu of the Re:system M51 and M10 devices. In a Multiroom system, the new sources have to be assigned to the corresponding remote buttons in the Remote menu, so that they can be called up in the side room. You will find a description of the Remote menu in the Re:system Device Startup Guide.
CD Control Re:source CD Control A) Display operation The following control functions are available at the device or through the Revox App through the display operation: • Play • Pause • Stop • Track (forwards/back) • Search 1-5 (fast search with 5 speeds) • Shuffle • Repeat: Repeat Track/ Disc • Open/close CD drawer C) M208 Remote control IR control through the CD Control module The M208 Project Manager offers the device control "Revox CD Oppo" in the [Revox] database, which makes the following CD play c
CD Control Re:source Multiroom operation Change/display track You can operate the CD function of the Blu-ray player from each side room, with the Revox Multiroom System. If the M217 wall-mounted display is installed, the track number and the status are displayed. Using the two buttons (shown with black/white squares) on the wallmounted operating panel, you can switch within the CD to the previous or the next track. Multiroom configuration The wall-mounted display shown below is showing the CD menu.
CD Control Re:source Technical data Audio connections: IN1 Cinch stereo input Cinch stereo input IN2 Cinch stereo input IN3 IN4 Cinch stereo input Max. cable length 10 m * Digital data connections: RS 232 Sub-D 9-pin - crossover cabling Plug-Plug * Dependent on cable environment and quality E&OE Warranty Scope of delivery Warranty covers a period of 24 months from the purchasing date. Your specialist dealer is your first contact if you need service help.
CD Control Re:source CD-Control module Operating manual / Part no.: 10.30.
