as82 of CD Control Module Joy E2.
Contents CD Control Module Joy Installation Connection panel 2 3 4 Cabling RS232 connection Audio connection 5 5 6 Setup Configuring the digital input Hiding analogue inputs Defining the CD switch-off behaviour 7 8 8 9 Analogue inputs IN 1-IN 3 Cabling Setup: Edit Name 10 10 11 General operation 12-13 CD control 14-16 Technical data Warranty 17 17 1
CD Control Re:source CD-Control Module Joy CD Player specifications Manufacturer: Revox Type: Joy CD Player The CD Control module is a universal audio interface with a serial communication port. Unlike the Re:system M51 and M100, the Re:system M10 device does not have an internal CD player. Working together with the Revox Joy CD Player, it is now possible to integrate a CD Player into a Multiroom system, which can be controlled from all side rooms.
CD Control Re:source INSTALLATION The CD-Control Module is equipped with the latest electronics and should be handled with care. Loosen the two screws with the TORX screwdriver supplied and remove the blanking plate. A suitable TORX screwdriver is supplied with the Re:system M51 and M10. Before you install the card, the M51/M10 must be switched off and separated from the power supply, by plugging the unit out.
CD Control Re:source Connection panel RS232 Serial interface with Sub D9 socket for controlling the Revox Joy CD Player. Audio connections The CD Control module independent audio inputs: IN 1 IN 2 IN 3 IN 4 for for for for has 4 Aux-1 Aux-2 Aux-3 Revox Joy CD Player Devices such as external tuners, MP3 players or SAT receivers can be connected to the analogue line inputs IN1 to IN3. Input IN 4 is connected with the audio outputs on the Joy CD Player.
CD Control Re:source CABLING RS232 connection The following cabling solutions are possible for the transfer between the CD Control Module and the Joy CD Player: A) For lengths up to 10m Normal multi-core cable with complete screening. B) For lengths up to 25m CAT7 cable. One pair of wires for each connection RX, GND, TX. The screening is connected to GND. C) With Revox prefabricated cable Length 1,5 m (Part number 1.561.020.
CD Control Re:source Audio connection: Input IN 4 The CD Player's audio output is connected to the IN 4 audio input (CD Control module) using a high quality stereo cinch cable. If a 5.1 Decoder module is available in the Re:system M51/M10, a digital audio connection can be established in addition - see the Chapter Configuring the digital input, Page 7.
CD Control Re:source SETUP CD-CONTROL Configuring the digital input The basic settings for the CD Control module are made in Setup. When installing the CD Control module in a Re:system M51 or M10 with an installed 5.1 Decoder module, you have the option to use the digital audio signal from the CD Player in the main room. In this case, the digital output (Coaxial/ Optical) is connected to the digital input on the 5.1 decoder module at the M51.
CD Control Re:source Configuring the digital input Hiding analogue inputs You can now select whether and which of the 5.1 decoder digital inputs should receive the digital signal, using the Dig. Input function. On the second page of the Setup (Menu softkey), the CD Control module offers the option of hiding the Aux-1, Aux-2 and Aux-3 analogue sources, if required. This option is only available in the CD source Setup menu - [Source CD > Setup > Source].
CD Control Defining the behaviour Re:source CD switch-off Power Off: System Off After the CD has been paused or stopped, the CD Player stays in this state. Only when all rooms including the main room are switched off, does the CD Player switch to standby mode. In standby mode, the CD Player needs 0.5 watts. If required, the CD Player can be turned off completely through the serial interface. You have 3 different switch off [Power Off] options to choose from.
CD Control Re:source Analogue input IN1 IN2 IN3 Connect the three analogue inputs IN1 – IN3 using a cinch stereo cable with your external device. The inputs are shown in the source menu as Aux-1 – Aux-3. The analogue inputs IN1 – IN3 are not suitable for connecting a record deck/ player. In this case, you should use the I/O module (article no.: 1.551.081.00), which supports both MM and MC sound systems. Both modules, the CD Control module and the I/O module, can be used together in the M51/ M10.
CD Control Re:source Setup Aux-1 / 2 / 3 Edit source name The display names of the three inputs and the CD source can be freely defined. Simply give a name that you can assign clearly. The Cursor softkeys move the [ ] cursor left and right respectively. The Delete softkey deletes a character where the [ ] cursor is positioned. Select the input from the SOURCE menu whose name you want to edit. CD, Aux-1, Aux-2, Aux-3 The Insert softkey inserts a character to the left of the [ ] cursor.
CD Control Re:source GENERAL OPERATION CD Menu If a CD Control module is installed, the sources Aux-1, Aux-2, Aux-3 and CD appear in the Source menu of the Re:system M51 and M10 devices. In a Multiroom system, the new sources have to be assigned top the corresponding remote buttons in the Remote menu, so that they can be called up in the side room. You will find a description of the Remote menu in the Re:system device Startup Guide.
CD Control Re:source Menu page 3 Here, the following functions are available: • [Pause/ Play] • [Repeat Disc/ Track] • [Shuffle] • [Search] Now you can search for a specific track using the Select and Page softkeys or start to play the first track immediately. In both cases, playback is started with the Play softkey. You can toggle between the 3 menu pages with the More softkey.
CD Control Re:source CD CONTROL Change/display track A) Multiroom Operation You can operate the CD function of the CD Player from each side room, with the Revox Multiroom System. If the M217 wall-mounted display is installed, the track number and the status are displayed. Using the two buttons (shown with black/white squares) on the wallmounted operating panel, you can switch within the CD to the previous or the next track.
CD Control Re:source B) Direct CDPlayer Operation The following functions can be executed through the glass front panel of the CD Player, in parallel to the control through the Communication Module: Sensor buttons Function Short press: Long press: switch on/off (OFF: min 0.5 sec.) Complete reset - (min. 5 sec.
CD Control Re:source C) Remote Control The CD Player can be remotely controlled through the CD Control module with the M208 System remote control or the RC M100. In the case of the M208, the M208 Project Manager offers the device control "Revox Joy CD Player" in the [Revox] database, which makes the following CD play control commands available via infrared: • • • • • • Switch on/off Play Pause Stop Track (forwards/ back) Search These commands can also be executed with an RC M100.
CD Control Re:source Technical data Audio connections: IN1 Cinch stereo input IN2 Cinch stereo input IN3 Cinch stereo input IN4 Cinch stereo input Max. cable length 10 m * CD Control Max. number of tracks: 100 Supports CD text in the most commonly used formats * Dependent on cable environment and quality E&OE Warranty Scope of delivery Warranty covers a period of 24 months from the purchasing date. Your specialist dealer is your first contact if you need service help.
CD Control Re:source User manual Joy CD-Control-Module / Article no.: 10.30.
