Owner`s manual

Graphic equalizer ,:::_::v,
Use to match the tonal quality of the center, surround L/R
and surround back L/R, surround back, presence L/R
speakers and the subwoofer with that of the fl'ont L/R
speakers. YOU can adjust 7 frequency bands (63Hz,
160Hz, 400Hz, lkHz, 2.5kHz, 6.3kHz, 16kHz).
Choices: -6.0 to +6.0 dB
Control step: 0.5 dB
÷ C:HlqlJl4Fl.* ,,I:RL-II4T L
+
63Hz 7Z;]j27Z I_%I_ldB
1L:,EIqZ .. @.. Et E_dl?
4W!Hz .. ql_ .. _. _2!dB
[.£] ['iF] ; UF q?OI,q'l
[ ,J,i] [> ] _gd iust
Press A / _ to select a frequency band and <51/ _> to adjust the
selected lrequency band.
Note
The "GEQ" parameter can be adjusted only when "GEQ" is
selected in "SELECT".
Test tone "i"i::,:::'"i""FI",Mi::
p¢,3===d'==11?_;r=Fi
H..'D;.!L]HLb'2B_.
C:HI:IIJlIL--I...FROIIT L
+
16kHz: C1,,EIdB
•_ TEST "TOIE .... CIFF
[,&] ["_]_i_lF [',::,kq-t
r _] r> ] _gd Just
Use this feature to make adjustments of "GEQ" while
listening to a test tone. To select "TEST TONE", press V
repeatedly in the graphic equalizer screen.
Choices: OF[::, ON
• Select "OFF" to stop test tones and output the currently
selected source component.
• Select "ON" to output test tones from the selected
speakers.
• Low-frequencyeffect level
i3::'LF:rEi..°i!![i...iEi..
Use this feature to adjust the output level of the LFE (low-
frequency effect) channel according to the capacity of
your subwoofer or headphones. The LFE channel carries
low-frequency special effects which are only added to
certain scenes. This setting is effective only when this unit
decodes Dolby Digital or DTS signals.
Control range: 20 to 0 dB
Control step: 1 dB
ii,,= I I Ii1=1
D,,'U"BL%IBL
÷ SPEF4KER...... _,:_l?
HEI:IDPHOIE .... F_dB
[ &] '['ta'] _UF [:,ol,ln
Speaker :!!!;F:'EAi::]!![F?.
Adjusts the speaker LFE level.
Headphone HE{:::IDF'HOI"E
Adjusts the headphone LFE level.
Depending on the settings of "LFE/BASS OUT" (see page 87),
some signals lllay not be output at the SUBWOOFEI ), OUTPUT
jack.
• Dynamic range C...'i:;,Ybil::iHi C RI:::Ii¢3E
Use this feature to select the amount of dynamic range
compression to be applied to your speakers or
headphones. This setting is effective only when this unit is
decoding Dolby Digital and DTS signals.
Choices: MIN, STD, MAX
• Select "MIN" (minimum) if'you regularly listen at low
volume levels.
• Select"STD" (standard) for general use.
• Select "MAX" (maximum) to preserve the greatest
amount of dynamic range.
_='.,= IH==IM?== }_l=l_ll=,_
.,,, _,,H,,.., ,r,,_,,,_g
+ SI:'= 1'1ii{ ':7,T[:,H,1FtX
HP_ 1'1114 ETE:,tH'II:I:
[&] ['g] _ UP [h::,kq-i
[4] [> ]_ Se iect
Speaker :!!!;F:'
Adjusts the speaker compression.
Headphone HF'
Adjusts the headphone compression.
92 En