Owner`s manual

YOUcan at!just tile output level of each speaker while
listening to a music source. This is also possible when
playing sources input at the MUUH CH 1NPUF,jacks.
Note
This operation will override the lexel adjustments made in
"AUTO SETUP" (see page 32) and "SP LEVEL" (see page 90).
Set the operation mode selector to AMP and
then press LEVEL on the remote control
repeatedly to select the speaker you want to
adjust.
_) LEVEL
S_JRCE
li2HDl"d"r'vi'..*...,i".,_ li Front leit speaker
' ="'" ="".... C p k
,...q..._.i_i..._.., enter s ea el"
li::'i:::'_"d"r'vF..*...'l".'_ l',,i:::' Front right speaker
,::7i ii:::, i:::, Summnd right speaker....-...q'.. :: F..
....,:::'i:::,,_...,_i.... Surround back right speaker
....,::=i:::,,_...,_i:::".. S un'ound back lelt speaker
,::7i ii:::, i Sun'ound lelt speaker
,::7i, i i:::'i:::, Sub'_o()ler
....-.,.q F..
ii:::'i:::'_"i'::rv.a.i....,i_.... Presence lelt speaker
i::,D]..E,::'V,H....,v.]:::' Presence right speaker
-#.
• Once you press LEVEL on the remote control, you can
also select the speaker by pressing _ / V.
• Instead of "SB R" and "SB L', "SB" is displayed if "SUR.
B L/R SP" is set to either "SMLx 1" or "LRGx 1" (see
page 89).
Press <1 / E>on the remote control to adjust
the speaker output level.
• Press ) to increase the value.
• Press ( to decrease the value.
Control range: 10 dB to +10 dB
PRESET/_H
A E/CAI'_. "-
YOUcan mix down multi-channel sources to 2 channels
and enjoy playback in 2-channel stereo.
1 Set the operation mode to AMP and then
press STEREO on the remote control
repeatedly to select "2ch Stereo".
STEREO
_UR_
¢5
,'% -. L. l'_ J.............
• You can use a subwoofer with this program when "LFE/BASS
OUT" is set to "SWFR" or "BOTH" (see page 87).
• Yon can also select the "2ch Stereo" mode by rotating the
PROGRAM selector on the fi'ont panel.
2 Press PARAMETER and then <1/ C>to set the
"DIRECT" parameter.
pRESEW_H
A E/CA_I ',
Choices: AUTO, OFF
• Select "AUTO" to bypass the decoders, DSP
processors and the tone control circuitry only when
"BASS" and "TREBLE" are set to 0 dB (see
page 50).
• Select "OFF" not to bypass the decoders, DSP
processors and the tone control circuitry when
"BASS" and "TREBLE" are set to 0 dB.
• When multi-channel signals (Dolby Digital and DTS) are
inpm, they are downmixed to 2 channels and output l]'om
the front lell and right speakers.
• The low-frequency signals input from the front lell and
right speakers arc redircctcd to the subwoofcr in the
lollowing cases:
-"LFE/BASS OUT" is set to "BOTH" (see page 87).
-"FRONT SP" is set to "SMALL" (see page 88) and
"LFE/BASS OUT" is set to "SWFR" (see page 87).
• Press PARAMETER again to exit from the parameter
setting mode.
51 En