Owner`s manual

Make sure of the following check points
before starting the AUTO SETUP operations.
• Speakers are connected appropriately.
• Supplied optimizer microphone is connected to this
unit and placed appropriately.
• Headphones are disconnected fi'om this unit.
• The room is sufficiently quiet.
• The video monitor connected to this unit is turned on.
Set the operation mode selector to AMP and
then press SET MENU to enter "SET MENU".
The top "SET MENU" display appears in the OSD.
=_FT k4FL IiI
2¢,i H_i'!U
+ .gUTO SETLIF'
.MI_IqUFILSETUP
.SIGH#L IMEO
E.,k]/ ['t_']_Ug,'Dc,kuq
EEMTER ]; En<:er
Press ENTERto enter "AUTO SETUP".
The "AUTO:MENU" display appears in the OSD.
,MJ_L_=i']r_i'9o,i PJi'?="l_ k_P_ Ii i
+ SETLIP ....... I:IUT0
i,]IR IM g ..... EHEC:K
DISTPMEE, _ _C:HEC:K
SIZE ....... EHEEK
EQ ....... I_glTLIR#L
LEUEL. ..... CHEEK
STPRT
I ,,k]/I"_'] _U_-/ [/ot,!n
['<]/[_'] ;SeiecL
Press < / _> to select "SETUP".
PRESETmH
A E/CA_ ',
Choices: AUTO, RELOAD
• Select "AUTO" to automatically run the entire
"AUTO SETUP" procedure.
• Select "RELOAD" to reload the last "AUTO
SETUP" settings and override the previous
settings. When you select "RELOAD", the
previous auto setup result appears in the OSD. See
step 7 on page 34 and carry out the operations.
"I_.ELOAD" is available ( nl 3 when you haxe previously run
"AUTO SETUP" and confirmed the resuhs.
7 Press A/ _7repeatedly to select "WIRING",
"DISTANCE", "SIZE", "EQ", or "LEVEL".
H_ i = =,,iL =I
SETLIP ....... I:IUTO
+ klIRIlqG..... EIqEC:K
D [STIOI4C;E...C:IqEC:I{
SIZE ....... EHEC:K
EQ ....... 14glTLIIRJ_L
LEUEL. ..... C:HEC:K
STPRT
[,,k]/[',_' ] _UF, [icik,q
[,_]/[i_]: Seiec%
This unit performs the following checks:
Speaker wiring i.di Ri ii(!!i
Checks which speakers are connected and the
polarity of each speaker.
Speaker distance [:,]ISFf::IM(];i!!!I
Checks the distance of each speaker from the
listening position and at!justs the timing of each
channel.
Speaker size :!!!;i Zi!!!i
Checks the frequency response of each speaker and
sets the appropriate low-frequency crossover for each
channel.
Choices: CHECK, SKIP
• Select "CHECK" to automatically check and adjust
the item.
• Select "SKIP" to skip the item and perform no
acljustments.
Parametric equalizer level i!!!);!
Adjusts the frequency and the parametric equalizer
level of each channel to reduce coloration across the
channels and create a cohesive sound field. This is
particularly important if"you use different brands or
sizes of speakers for some channels or have a room
with unique sonic characteristics. In addition, the
fi'equency response of each channel is adjusted in
accordance with the sound output fi'om your fi'ont
speakers.
Choices: NATURAL, FLAT, FRONT, SKIP
• Select "NATURAL" to average out the fi'equency
response of all speakers with higher fi'equencies
being less emphasized. Recommended if the FLAT
setting sounds a little harsh.
• Select "FLAT" to average the fi'equency response
of all speakers. Recommended if all of your
speakers are of similar quality.
• Select "FRONT" to adjust the fi'equency response
of each speaker in accordance with the sound of
your fi'ont speakers. Recommended if your fi'ont
speakers are of much higher quality than your other
speakers.
• Select "SKIP" to skip the selected item and
perform no adjustments.
33 En