Owner`s manual

Ii_o_Wl:l=r_R.=r.) il,v,
During AUTO SETUP
l....i:::'.... ._.'{"' l'P.Ji"ii%li:::'i:::u'=iir'r'i"l".'...q".' i ....'IC:'i:::' I:ron[ L/R ch;{nneI signals ;Ire not detected. Check the l'r()nt L/R speaker connections. 14
i....i:::'":*.=:,=,," li"ii%.p.J..., ,...q ...F..c:'iliPiD ==....q'::'D A surround channel signal is not detected. (heck the stlrround speaker connections. I4
E3 ',',i"i0 i:::'i:;I:i'E;,, !!!;F:' A presence channel signal is not detected. Check tile presence speaker connections. 14
i....i:::''""i"T"' -.q...q",4::'i::MD......""':__::'i....'_..'_.. Onl} ri_ht_ surround back channel si_nal_ is Connect tile surround back speaker to tile
detected. LEFT SURROUND BACK SPEAKERS
I4
terminal iI you only ha_e one surround
back speaker.
l....i:::''"i::::....'"' I 'P...'i"i ¢=1a.T-.'*:::'i.ii Background noise is too loud. "Fry rtlnning %UTO SETUP" ill a quiet
en*,ironment.
Turn ofi noisy electric equipment like air
conditioners or moxe them awa> from tile
optimizer microphone.
i:::'.....,:::,, _".i...ii:::T'.i...',:::'iEl:::, Surf(rand back speakers are connected. ( onnect sLtrrotlndspeakers when ,.ou use
though surround L/R speakers are not. surround back speakers.
_....i:::'-"::_,,H,...,"i..i,'-___._.,....i"ii' ,'-. Tile optimizer microphone was unpklgged Connect tile supplied optimizer microphone
during tile %UTO SETUP" procedure, to tile OI TIMIZER MIC.jack on tile Iront 32
panel.
E-',!!!{',',{".i0 '!!!i]i(!_H{:::Ii.... Tile optimizer i;_ticrophonedoes not detect (heck tile microphone setting. 32
test tones.
Check tile speaker connections and 14
placement.
i:::'.....,:::_,, ii,:::'i::'i:::,,".,"_i..h".i::'i Tile _'AUTOSETUP" procedure was Run %UTO SETUP" a_ain.
i.... ..=.,, *...,....,,...a...,....,..'.,i.,,....,...a _ 32
cancelled due to user actixit}.
i:::'_... '{ I'::i ,, T ir.F'I"i:::'I::M..IF'ii i:::'i:::'i:::'i'=li:::' All internal error occtlrred. Rm/_AUTO SETUP" a_ain. 32
i.... .{**:..i, .{.H i i....F..HF'H...= i....F..F.J...,F..
After AUTO SETUP
*.'.'i'i""._.'{,,,, *...''..._{"ii r'i") *...,i{"i ill:" lillM"i{"i'712:'ii r"l ....,i Speaker polarity is not correct. This (heck tile speaker connections l'or proper
message m% appear depending on tile polarity (+ or ). 14
speakers exen when tile speakers are
connected correctly.
kl-:,::*=',',UUkA',:'. :,::*='::{.r"!_:.::::',I::J'V'I:..) Tile distance between tile speaker and the Bring tile speaker closer to tile listening
listening position is oxer z4 Ill {g0 ft/. position.
*.,.,i'i":_=....,,,"_....i...='..."_....i....ii:::"iii:::'i i...a'..v..,...,_'..i::"i:::'i:::'¢=_i:::' Tile difference oI *,olume lexel at;ion_ Readjust tile speaker installation so that all
speakers is excessixe, speakers are set in locations with similar
conditions.
(heck tile speaker connections.
Use speakers ol simitar quality.
Adjust tile output xolume oi tile subwooler.
14
32
• If the "ERROR" or "WARNING" screens appears, check the cause of the problem, then run "AUTO SETUP" again.
• If warning "W- 1" appears, corrections arc made, but they may not be optimah
• If warning "W-2" or "W-3" appears, no corrections arc made.
• If error "E- 10" occurs repeatedly, please contact a qualified YAMAHA service center.
129 En