Owner`s manual

• Speaker impedance ,::[,i:::,i:::.,..=li.Fi:::.i:::, Ti.,.ii:)....q L,,r_i'=.L,,l',, a, I u ::
Use this feature to set tile speaker impedance of this unit
st) that it matches tbat of your speakers.
Cboices: 8_QMIN, 6_QMIN
• Select "Sf2M1N" to set the speaker impedance to 8 f!.
• Select "6L)MIN" to set tbe speaker impedance to 6 L).
The impedance of each
Front speaker must be 8 tl or
highm:
8t)M[N
Center
The impedance of each
Surround speaker must be 8 _ or
higher.
Surround back
The impedance of each
Front speaker must be 4 _1_or
higher.
6t)M[N
Center
The impedance of each
Surround speaker must be 6 t_ or
higher.
Surround back
• User presets U:!!;ERF::'RE:!!;ET
Use this feature to reset all the parameters of this unit to
the initial factory settings (see page 130).
Choices: CANCEL, RESET
• Select "CANCEL" not to reset any parameters of this
unit.
• Select "RESET" to reset the parameters of this unit.
• This setting completely resets all the parameters of this unit
including the "SET MENU" parameters. However, the
advanced setup menu parameters will not be initialized.
• The initial factory settings are acuvated next time you turn on
this unit.
• Remote sensor REi40TE SEi.E!:0F;?.
Use this feature to activate or deactivate the signal-
receiving capability of the remote control sensor on the
front panel of this unit.
Choices: ON, OFF
• Select "ON" if you want to activate the signal-
receiving capability of the remote control sensor.
• Select "OFF' if you want to deactivate the signal-
receiving capability of the remote control sensor.
Note
We recommend setting the parameter to "ON" in most cases.
• Wake on RS-232C access
Use this feature to set this unit to transmit data via the P,S-
232C interface when this unit is in tbe standby mode.
Choices: YES, NO
Initial setting:
[U.S.A. and Canada models]: YES
[Otber models]: NO
• Select "YES" to set tbis unit to transmit data via tbe
RS-232C interface.
• Select "NO" to set tbis unit not to transmit data via tbe
RS-232C interface.
• Remote control AMP ID
F;?£:AI"iF' ]:[:'
Use this feature to set the AMP ID of this unit for remote
control recognition (see page 104).
Choices: ID1, ID2
• Select "IDI" when the remote control AMP ID library
code is set to "2001".
• Select "ID2" when the remote control AMP ID library
code is set to "2002".
Noto
You need to set the corresponding remote control AMP library
code lor the remote control (see page 104).
• Remote control TUNER ID
i2M"' Ti iMi:::'iD T i"=
Use this feature to set the TUNER ID of this unit for
remote conm)l recognition (see page 121 ).
Cboices: ID1, tD2
• Select "IDI" wben the remote c(mtrol TUNER ID
library code is set to "2602".
• Select "ID2" when tbe remote c(mtrol TUNER ID
library code is set to "2603".
You need to set the corresponding remote control TUNER library
code lor the remote control (see page 121).
• Remote control XM ID _:::,,-.:'..'i',=i'ri".,
F,,,,,.. :"H I a, L,'
(U.S.A. and Canada models only)
Use this feature to set the XM ID of tbis unit for remote
control recognition (see page 121).
Cboices: 1131, tD2
• Select "IDI" when the remote conm)l XM ID library
code is set to "2604".
• Select "ID2" when the remote conm)l XM ID library
code is set to "2605".
You need to set the corresponding remote control XM library
code lot the rentote control (see page 121).
118 En