Owner`s manual

Use this menu to adjust the optional system parameters.
,4 ¢¢WT¢_Li MI"%tH 4 ,-"t
UF iUJh i'igZ'iU i, r'4
+ iq)bIEPLJ:f,' SFT
B)HEHOR',' gCgflRb
C)I:ILID10 EELECT
D)[)ECCI[ER IqCI[,E
[.,_,] ["_] _:OF 'Dc,_,!n
[ EHTER ] : Enter
A I_=W'CT:_iLJ i,,,ii"_iii i #'t ,,,"t
UF{iU!'! , ...,,'..,4,' 4
+ E)F'gRIqN, IHi
F?ZONESET
G)',:,H RgDIO SET
H) DOC:K SET
[&]' ['_] aLI_:'Do_,Jn
[ ENTER ] _Enter
• Display settings ,",'.,r'.,'r(::'D_,"v..,,:::c'"r'
Use the "V-RESET" in "ADVANCED SETUP" to set the
parameters in "DISPLAY SET" (except "DIMMER', "SHOI_I"
MESSAGE", "ON SCREEN" and "FL SCROLL") to the factory
presets (see page 119).
:=/,r Y==t_,!,_!¢1_=YT
H,,'L,i JFL, ,, Jg{
+ DIHI1ER .......... @
OSD SHIFT ....... @
GRF]','BJ%-:I:.... PUTO
O C:OI4H,,_ ....... 014
[.A] [',r] _Lh= Dc,_,_n
[ 4] '[> ] H_dJ us{
Dimmer 1:::,i HHER
Use this feature to adjust the brightness of"the front panel
display.
Control range: 4 to 0
Control step: 1
• Press <1 to make the front panel display dimmer.
• Press C:>to make the front panel display brighter.
OSD shift O:!!!;[):!!!;i'4i F'"[
Use this feature to adjust the vertical position of the OSD.
Control range: 5 (upward) to +5 (downward)
Control step: 1
Initial setting: 0
• Press <1 to raise the position of the OSD.
• Press C:>to lower the position of the OSD.
Gray back I':::i:::,l"li..ii::'l"u"'i.."
*,,,ll',J",, i l,Jr"l,,,,,l',,
Use this feature to display a gray background in your
video monitor when there is no video signal being input.
Choices: AUTO, OFF
• Select "AUTO" to display a gray background in your
video monitor when there is no video signal being
input.
• Select "'OFF" not to display a gray background in your
vide() monitor.
• Depending on the xideo signals being input or the system
setting ol your ddeo monitor (NTSC or PAL), the OSD may be
displayed abnormally. In such cases, set "GRAY BACK" to
"OFF".
• Even when "GRAY BACK" is set to "OFF", the OSD may not
be displayed correctly depending on the conditions ol the
picture.
Video conversion i i ,"',",kii i
Use this feature to set whether to convert the video signals
input at the VIDEO, S VIDEO and COMPONENT
VIDEO .jacks.
Choices: ON, OFF
• Select "ON" to convert composite, S-video and
component video signals interchangeably and up-
convert composite and S-video and component video
signals to HDMI video signals.
• Select "OFF" not to convert any signals.
• This unit does not convert 480 line vide() signals and 576 line
video signals intercbangeably.
• The analog component video signals with 480i (NTSC)/576i
(PAL) of resolution are converted to the s-video or composite
video signals and output at the S VlDEO MONlTOR OUT and
VIDEO MONITOR OUT jacks.
• The converted video signals are only output at the MONITOR
OUT jacks. When recording a video source, you must make the
same type of vide() connections between each component.
• When composite video or S-video signals from a VCR are
converted to component video signals, the picture quality may
suffer depending on your VCR.
• Set "V CONV." to "ON" to display the sound field parameter
display and short message display.
• Unconventional signals input at the composite video or S-video
jacks cannot be converted or may be output abnormally. In such
cases, set "V CONV." to "OFF".
• When non-standard vide() signals (such as vide() signals from a
game console) are input, this unit may not convert the signals
even if you set "V CONV." to "ON".
97 En